GP1670F_1870F Operator's Manual - Furuno USA

More documents

Recommendations

Info

13. INSTALLATION19°-22° transom angle (small aluminum and fiberglass boats): Position theshim with the tapered end up.2º-10ºtransomangle11º transom angleNO SHIM19º-22ºtransomangleshim withtaper downshim withtaper upYES YES YESparallel parallel parallel12º-18º transom angleNO SHIMNO YESNOanglereversedslightangleangle toosteep3. If the bracket has been temporarily fastened to the transom, remove it. Apply amarine sealant to the threads of the three #10 x 1-1/4” self-tapping screws to preventwater seeping into the transom. Screw the bracket to the hull. Do not tightenthe screws completely at this time.4. Repeat step 1 to ensure that the angle of the sensor is correct.Note: Do not position the sensor farther into the water than necessary to avoidincreasing drag, spray, and water noise and reducing boat speed.5. Using the vertical adjustment space on the bracket slots, slide the sensor up ordown to provide a projection of 3 mm (1/8”). Tighten the screws.Cable coverCableclamp50 mm (2")Hull projection 3 mm (1/8")13-10
13. INSTALLATIONHow to attach the sensor to the bracket1. If the retaining cover near the top of the bracket is closed, open it by depressingthe latch and rotating the cover downward.Step 1 Step 2LatchPivotarmRetainingcoverStep 3Step 4Slot2. Insert the sensor's pivot arms into the slots near the top of the bracket.3. Maintain pressure until the pivot arms click into place.4. Rotate the sensor downward until the bottom snaps into the bracket.5. Close the retaining cover to prevent the accidental release of the sensor whenyour boat is underway.How to route the cableRoute the sensor cable over the transom, through a drain hole, or through a new holedrilled in the transom above the waterline.Never cut the cable or remote the connector; this will void the warranty. Always wearsafety goggles and a dust mask.1. If a hole must be drilled, choose a location well above the waterline. Check for obstructionssuch as trim tabs, pumps, or wiring inside the hull. Mark the locationwith a pencil. Drill a hole through the transom using a 19 mm or 3/4” bit (to accommodatethe connector).2. Route the cable over or through the transom.3. On the outside of the hull secure the cable against the transom using the cableclamps. Position a cable clamp 50 mm (2") above the bracket and mark themounting hole with a pencil.4. Position the second cable clamp halfway between the first clamp and the cablehole. Mark this mounting hole.5. If a hole has been drilled in the transom, open the appropriate slot in the transomcable cover. Position the cover over the cable where it enters the hull. Mark thetwo mounting holes.6. At each of the marked locations, use a 3 mm or 1/8” bit to drill a hole 10 mm (3/8”) deep. The prevent drilling too deeply, wrap masking tape around the bit 10 mm(3/8”) from the point.13-11
Page 1 and 2:
GPS PLOTTER/SOUNDERModelGP-1670F/GP
Page 3 and 4:
IMPORTANT NOTICESGeneral• This ma
Page 5 and 6:
SAFETY INSTRUCTIONSCAUTIONDo no tur
Page 7 and 8:
TABLE OF CONTENTS3.2.3 How to enter
Page 9 and 10:
TABLE OF CONTENTS9. MEMORY CARD OPE
Page 11 and 12:
FOREWORDA Word to GP-1670F, GP-1870
Page 13 and 14:
SYSTEM CONFIGURATIONThe environment
Page 15 and 16:
EQUIPMENT LISTSName Type Code no. R
Page 17 and 18:
1. OPERATIONAL OVERVIEW1.1 Controls
Page 19 and 20:
1. OPERATIONAL OVERVIEWTested SD ca
Page 21 and 22:
1. OPERATIONAL OVERVIEW1.2 RotoKey
Page 23 and 24:
1. OPERATIONAL OVERVIEW2D plotter d
Page 25 and 26:
1. OPERATIONAL OVERVIEW1.6 The Curs
Page 27 and 28:
1.8 Home Screen (Display Selection)
Page 29 and 30:
1. OPERATIONAL OVERVIEW5. Select a
Page 31 and 32:
1. OPERATIONAL OVERVIEWWind meter+n
Page 33 and 34:
1. OPERATIONAL OVERVIEWHow to selec
Page 35 and 36:
1. OPERATIONAL OVERVIEWAuto course-
Page 37 and 38:
1. OPERATIONAL OVERVIEW4) Press the
Page 39 and 40:
1. OPERATIONAL OVERVIEWItem Context
Page 41 and 42:
1. OPERATIONAL OVERVIEW1.17 Tide In
Page 43 and 44:
2. TRACKYour boat’s track is plot
Page 45 and 46:
2.7 How to Delete Track by Color2.
Page 47 and 48:
3. POINTS3.1 What is a Point?In nav
Page 49 and 50:
3. POINTS[Hide]: Hide the icon and
Page 51 and 52:
3. POINTS3.5 How to Select Visibili
Page 53 and 54:
4. ROUTES4.1 What is a Route?Often
Page 55 and 56:
4. ROUTES5) After you have entered
Page 57 and 58:
4. ROUTES4. Select [EASY ROUTING] f
Page 59 and 60:
4. ROUTES4.4 How to Insert a Point
Page 61 and 62:
4. ROUTES4.7.2 Functions available
Page 63 and 64:
4. ROUTES4.9 How to Display a Route
Page 65 and 66:
5. NAVIGATIONThis chapter shows you
Page 67 and 68:
5. NAVIGATION• A red line runs be
Page 69 and 70:
6. MAP SETTINGS, 2D PERSPEC-TIVE/3D
Page 71 and 72:
6. MAP SETTINGS, 2D PERSPECTIVE/3D
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
7. FISH FINDER OPERATIONS7.1 How th
Page 79 and 80:
7.3 How to Activate the Fish Finder
Page 81 and 82:
7. FISH FINDER OPERATIONSMarker zoo
Page 83 and 84:
7. FISH FINDER OPERATIONS• The 60
Page 85 and 86:
7.6 Manual Fish Finder Operation7.
Page 87 and 88:
7. FISH FINDER OPERATIONSClutter7.7
Page 89 and 90:
7. FISH FINDER OPERATIONS7.10 How t
Page 91 and 92:
7.14.1 How to set an alarm7. FISH F
Page 93 and 94: 7. FISH FINDER OPERATIONS7.15.2 How
Page 95 and 96: 7.17 FISH FINDER Menu7. FISH FINDER
Page 97 and 98: 7. FISH FINDER OPERATIONSItem[50 kH
Page 99 and 100: 7. FISH FINDER OPERATIONSBottom con
Page 101 and 102: 7. FISH FINDER OPERATIONSPlanktonA
Page 103 and 104: 8. ALARMSThe plotter section has 11
Page 105 and 106: 8. ALARMS8.4 XTE AlarmThe XTE (cros
Page 107 and 108: 8. ALARMS8.8 Anchor AlarmThe anchor
Page 109 and 110: 9. MEMORY CARD OPERATIONSThis syste
Page 111 and 112: 9.6 How to Delete Files from an SD
Page 113 and 114: 9. MEMORY CARD OPERATIONS9.8.3 How
Page 115 and 116: 10. OTHER FUNCTIONS10.1 AIS Operati
Page 117 and 118: 10.2 DSC Message Information10. OTH
Page 119 and 120: 10. OTHER FUNCTIONS10.4 How to Sele
Page 121 and 122: 10. OTHER FUNCTIONS10.5 Engine Disp
Page 123 and 124: 11. CUSTOMIZING YOUR UNITThe defaul
Page 125 and 126: 11. CUSTOMIZING YOUR UNIT11.3 SYSTE
Page 127 and 128: 11. CUSTOMIZING YOUR UNIT[RESTART G
Page 129 and 130: 12. MAINTENANCE,TROUBLESHOOTINGThis
Page 131 and 132: 12. MAINTENANCE, TROUBLESHOOTINGPro
Page 133 and 134: 12. MAINTENANCE, TROUBLESHOOTING12.
Page 135 and 136: 13. INSTALLATION13.1 Installation o
Page 137 and 138: 13. INSTALLATIONin a position where
Page 139 and 140: 13.3.2 Transom mount transducer13.
Page 141 and 142: 13. INSTALLATION3. Wipe off any san
Page 143: 13. INSTALLATIONHow to install the
Page 147 and 148: 13. INSTALLATION8. Launch your boat
Page 149 and 150: 13.5 Wiring13. INSTALLATIONAll wiri
Page 151 and 152: 13. INSTALLATIONHow to extend cable
Page 153 and 154: 13. INSTALLATION13.6 Initial Settin
Page 155 and 156: 13. INSTALLATION13.6.2 CAN bus inpu
Page 157 and 158: 13. INSTALLATIONPGNDescription12748
Page 159 and 160: APPENDIX 1 MENU TREEESC/MENU(long p
Page 161 and 162: APPENDIX 1 MENU TREE11(Con’t from
Page 163 and 164: APPENDIX 1 MENU TREE1(Con’t from
Page 165 and 166: APPENDIX 2 ABBREVIATIONS, SYMBOLSAb
Page 167 and 168: APPENDIX 2 ABBREVIATIONS, SYMBOLSSy
Page 169 and 170: APPENDIX 3 JIS CABLE GUIDECables li
Page 171 and 172: FURUNOGP-1670F/1870FSPECIFICATIONS
Page 173 and 174: PACKING LIST GP-1670F-E 14CW-X-9852
Page 175 and 176: D-1
Page 177 and 178: D-3
Page 179 and 180: D-5
Page 181 and 182: INDEXNumerics2D perspective dispay.
Page 183 and 184: INDEXrecording interval............
Page 185: FURUNO Warranty for North AmericaFU
show all

GP1670F_1870F Operator's Manual - Furuno USA

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?