User Manual - MBS Survey Software Ltd.

More documents

Recommendations

Info

DGBFIEPNLDKSNFINJCNROKPLHRUSCZvalue is adopted. Aim at the lower point andpress this button to trigger the measurement(3). The result is displayed in the summary line, thepartial results in the secondary lines.Indirect measurement - determining a chainvalue using 3 measurements1 2e.g. determining the height between point 1 andpoint 2 using three target points.Press this button six times; the display showsthe following symbol . The laser is switched on.Aim at the upper point (1).Press this button and trigger the measurement.After the first measurement the value is adopted. Thedisplay flashes (2).3Triggers the measurement. After the secondmeasurement the value is adopted. The displayflashes (3).Press and hold down this button to triggercontinuous measurement. Sweep the laser up anddown over the ideal target point.Press this button to end continuous measurement.The result is displayed in the summary line, thepartial results in the secondary lines.Storage of constants/historicalstorageStorage of a constantYou can store and recall a frequently used value e.g.height of a room. Measure the desired distance,press and hold the button until the device beepsto confirm storage.Recalling the constantPress this button once to recall the constantand make it available for further calculations bypressing button .Adjusting the constantPress the button for longer to change the constant- the constant flashes, you can now change theFunctions18Leica DISTO D3a BT 776750 gb
constant to the required value using the orbutton. Press the button to save the constant.Historical storagePress this button twice and the previous 20results (measurements or calculated results) areshown in reverse order.The and buttons can be used for navigation.Press this button to use a result from thesummary line for further calculations.Pressing the and buttons at the sametime erases all the values in historical storage.Timer (self-triggering)Press this button to set a 5-second time delay.orPress and hold down this button until thedesired time delay is reached (max. 60 seconds).WorkingOnce the key is released the remaining seconds untilmeasurement (e.g. 59, 58, 57...) are displayed in acountdown. The last 5 seconds are counted downwith a beep. After the last beep the measurement istaken and the value is displayed.The timer can be used for all measurements.with BLUETOOTH®Switching on BLUETOOTH® /sending measurementsA quick press on the - key starts DISTO BLUE-TOOTH®. The data connection must then be establishedout from a Pocket PC / PC by the applicationsoftware. A BLUETOOTH® - icon will appear in thedisplay until this has been successfully completed.BLUETOOTH® automatically switches off if theconnection to the Pocket PC / PC is not establishedwithin 240 sec from when the BLUETOOTH® wasswitched on.Whilst the first connection between thePocket PC/PC and the DISTO is being established, aprompt for the Pin-code of the DISTO may bedisplayed. In this case, enter the code 0000 into yourPocket PC/PC.Switching off BLUETOOTH®BLUETOOTH® switches off as soon as the DISTO isswitched off.DGBFIEPNLDKSNFINJCNROKPLHRUSCZLeica DISTO D3a BT 776750 gb19 Working with BLUETOOTH®
Page 1 and 2: User ManualEnglishCongratulations o
Page 3 and 4: • To understand the safety instru
Page 5 and 6: • Do not use the product near you
Page 7 and 8: Changing the reference point(multif
Page 9 and 10: Menu functionsSettingsThe menu allo
Page 11 and 12: Reset - returning the instrument to
Page 13 and 14: Laser continuousPress and hold down
Page 15 and 16: Triangular areaThe area of a triang
Page 17: Indirect measurement - determining
Page 21 and 22: Cause245 2nd button pressedalthough
Page 23 and 24: CareDo not immerse the instrument i
Page 25: Leica Geosystems AG, Heerbrugg, Swi

User Manual - MBS Survey Software Ltd.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?