Liebert Challenger 3000 with iCOM

More documents

Recommendations

Info

Installation (Applicable to all Models)Figure 6Piping connections for split system fan coil units - Downflow modelsLiebert iCOMControlPIPING OUTLET LOCATIONS(See Cabinet and FloorPlanning Dimensional Datafor Piping Opening Sizes.)Condensate Drain3/4" FPTField pitch a minimumof 1/8" (3.2mm) per ft. (305mm).The drainline must complywith all applicable codes.HumidifierWater Supply Line1/4" OD CULiquid Refrigerant Line#6 Quick Connect on Models BF036E/BF035E1/2" OD CU on Models BF060E/BF059ESuction Refrigerant Line#11 Quick Connect on Models BF036E/BF035E1-1/8" OD CU on Models BF060E/BF059EHot Water Return5/8" OD CU (optional)Hot Water Supply5/8" OD CU (optional)DPN000376Rev. 0112
Installation (Applicable to all Models)Figure 7Piping connections for split system fan coil units - Upflow modelsPiping outlet locations through theplenum are the same as the unit.See below for descriptions andconnection sizes.Humidifier Water Supply Line1/4" OD CUSuction Refrigerant Line#11 Quick Connect on Models BU036E/BU035E1 1/8" OD CU on Models BU060E/BU059ECondensate Pump Line1/2" OD CU; used onlyif optional condensate pump is ordered.Hot Water Return5/8" OD CU (optional)Liquid Refrigerant Line#6 Quick Connect on Models BU036E/BU035E1/2" OD CU on Models BU060E/BU059EHot Water Supply5/8" OD CU (optional)iCOM ControlPanelCondensate Drain; 3/4" FPTField-pitch a min. of 1/8" (3.2mm) per ft. (305mm). Units withouta condensate pump have a factory-supplied trap in the unit, so afield trap should not be added. Units with a condensate pump willrequire a field-supplied trap downstream from the pump. Thedrain line must comply with all applicable codes. (If condensatepump is ordered, piping is out top of unit).PIPING OUTLET LOCATIONS(See Cabinet and Floor PlanningDimensional Data for PipingOpening Sizes.)DPN000375Rev. 0113
Page 1: Precision CoolingFor Business-Criti
Page 5 and 6: 7.5 Centrifugal Air-Cooled Condensi
Page 7 and 8: IMPORTANT SAFETY INSTRUCTIONSSAVE T
Page 9 and 10: Introduction1.0 INTRODUCTION1.1 Sys
Page 11 and 12: Installation (Applicable to all Mod
Page 17: Installation (Applicable to all Mod
Page 23 and 24: Figure 11 Piping connections for ch
Page 29 and 30: 3.0 AIR-COOLED MODELS—SELF-CONTAI
Page 31 and 32: Air-Cooled Models—Self-Contained
Page 39 and 40: Figure 17 General arrangement—Air
Page 41 and 42: 4.0 WATER-COOLED MODELS—SELF-CONT
Page 43 and 44: Figure 20 General arrangement diagr
Page 45 and 46: Water-Cooled Models—Self-Containe
Page 47 and 48: Glycol/GLYCOOL-Cooled Models—Self
Page 49 and 50: NOTICEGlycol/GLYCOOL-Cooled Models
Page 51 and 52: 5.5.2 Glycol SolutionsGlycol/GLYCOO
Page 57 and 58: Figure 27 General arrangement—GLY
Page 59 and 60: 5.5.4 Motor Ball Valve—Digital Sc
Page 61 and 62: Chilled Water ModelsFigure 30 Chill
Page 63 and 64: 7.2.2 Low VoltageSplit System Model
Page 65 and 66: Split System ModelsTable 24 Line co
Page 67 and 68: Table 26Horizontal air discharge ca
Page 69 and 70:
Table 28Split System ModelsCabinet
Page 71 and 72:
Split System Models7.5 Centrifugal
Page 73 and 74:
Figure 36 3-ton centrifugal air-coo
Page 75 and 76:
Split System ModelsFigure 38 5-ton
Page 77 and 78:
Split System ModelsFigure 40 Split
Page 79 and 80:
7.6.4 Glycol SystemsSplit System Mo
Page 81 and 82:
Split System ModelsFigure 43 5-ton
Page 83 and 84:
R407C Refrigerant8.0 R407C REFRIGER
Page 85 and 86:
R407C RefrigerantNOTES79
Page 88:
Ensuring The High AvailabilityOf Mi
show all

Liebert Challenger 3000 with iCOM

Create successful ePaper yourself

Delete template?

Save as template?