Liebert Challenger 3000 with iCOM

More documents

Recommendations

Info

Split System ModelsFigure 37 3-ton centrifugal air-cooled condensing unit (con't.)Field-supplied unit disconnectswitch when optional disconnectis not provided in unitSingle- or three-phaseelectric servicenot by LiebertField-supplied 24VNEC Class 2 wiringto fan/coil unitLine voltage electric powersupply conduit entranceOptional factory-installeddisconnect switchFactory-wiredto componentson electric panelSingle- or three-phaseelectric servicenot by LiebertConnection terminalfor field-suppliedgrounding wireLow-voltage electricpower supply entranceWire connections from evaporatormod:1. 24V ground2. 24V supply3. High-pressure alarm (optional)4. Hot gas bypass connection(only on units with hot gasbypass)Heat rejection connection.Field-supplied 24V NECClass 2 wiring. See NOTE 2.DPN000207Rev0NOTES:1. Refer to specification sheet for full load amp. and wire size amp. ratings.2. Control voltage wiring must be a minimum of 16 GA (1.6mm) for up to 75' (23m)or not to exceed 1 volt drop in control line.68
Split System ModelsFigure 38 5-ton centrifugal air-cooled condensing unit dimensional dataCustomer-suppliedthreaded rods formodule supportfrom ceiling (typ. 4)54"(1371.6mm)CabinetDimension48"(1219.2mm)1-5/8"(41.1mm)32"(812.8mm)CabinetDimension15-3/4"(400mm)8-15/16"(227mm)3-3/8"(85.7mm)21-1/4"(539.8mm)14-1/2"(368.3mm)24"(610mm)CabinetDimension1-3/4"(44.5mm)33-5/8"(854.1mm)Threaded RodCenters1/2" (12.7mm) dia. holes forthreaded rods (typ. 2 each end)51-13/16"(1316mm)Threaded RodCentersHangerBracketNOTE: Unit is spaced evenly inreference to threadedrod centers.Shaded area indicates arecommended clearance of30" (762mm) for componentaccess and removal.7/8" (22.2mm) & 1-1/8" (28.6mm)dia. knockouts electrical entrance for highvoltageconnection (Single Point Power Kit)7/8" (22.2mm) & 1-1/8" (28.6mm)dia. knockouts electrical entrancefor high-voltage connectionSingle Point Power Kitconnection to EvaporatorAir InletLiquid Line male quickconnect locationAirOutletSuction Line male quickconnect location7/8" (22.2mm) dia. knockoutelectrical entrance for alternatecontrol panel low-voltage routing7/8" (22.2mm) dia.electrical entrancefor low voltage connectionSL-11087 Pg. 469
Page 1:
Precision CoolingFor Business-Criti
Page 5 and 6:
7.5 Centrifugal Air-Cooled Condensi
Page 7 and 8:
IMPORTANT SAFETY INSTRUCTIONSSAVE T
Page 9 and 10:
Introduction1.0 INTRODUCTION1.1 Sys
Page 11 and 12:
Installation (Applicable to all Mod
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24: Figure 11 Piping connections for ch
Page 25 and 26: Installation (Applicable to all Mod
Page 27 and 28: Installation (Applicable to all Mod
Page 29 and 30: 3.0 AIR-COOLED MODELS—SELF-CONTAI
Page 31 and 32: Air-Cooled Models—Self-Contained
Page 39 and 40: Figure 17 General arrangement—Air
Page 41 and 42: 4.0 WATER-COOLED MODELS—SELF-CONT
Page 43 and 44: Figure 20 General arrangement diagr
Page 45 and 46: Water-Cooled Models—Self-Containe
Page 47 and 48: Glycol/GLYCOOL-Cooled Models—Self
Page 49 and 50: NOTICEGlycol/GLYCOOL-Cooled Models
Page 51 and 52: 5.5.2 Glycol SolutionsGlycol/GLYCOO
Page 57 and 58: Figure 27 General arrangement—GLY
Page 59 and 60: 5.5.4 Motor Ball Valve—Digital Sc
Page 61 and 62: Chilled Water ModelsFigure 30 Chill
Page 63 and 64: 7.2.2 Low VoltageSplit System Model
Page 65 and 66: Split System ModelsTable 24 Line co
Page 67 and 68: Table 26Horizontal air discharge ca
Page 69 and 70: Table 28Split System ModelsCabinet
Page 71 and 72: Split System Models7.5 Centrifugal
Page 73: Figure 36 3-ton centrifugal air-coo
Page 77 and 78: Split System ModelsFigure 40 Split
Page 79 and 80: 7.6.4 Glycol SystemsSplit System Mo
Page 81 and 82: Split System ModelsFigure 43 5-ton
Page 83 and 84: R407C Refrigerant8.0 R407C REFRIGER
Page 85 and 86: R407C RefrigerantNOTES79
Page 88: Ensuring The High AvailabilityOf Mi
show all

Liebert Challenger 3000 with iCOM

Create successful ePaper yourself

Delete template?

Save as template?