Liebert Challenger 3000 with iCOM

More documents

Recommendations

Info

Split System ModelsFigure 34 Electrical field connections, prop fan condensing moduleField-supplied unitdisconnect switchTOP AIRDISCHARGE MODELS(5-Ton High Ambient& 5-Ton Quiet-Line)HORIZONTAL AIR DISCHARGE MODELSField-supplied 24V NECClass 2 wiring toevaporator moduleSingle- or3-phase electricservice; not byLiebertSL-11081Pg. 8AField-supplied 24VNEC Class 2 wiringto evaporatormoduleSingle- or3-phaseelectricservice; notby LiebertElectric serviceconnection to contactoror terminal blockFactory-wiredto components onelectric panel.Single- or 3-phaseelectric service; notby LiebertHigh-voltage electricpower supply entranceLow-voltage electricpower supply entranceEarth ground connectionterminal for field wiring.SL-11081 Pg. 8NOTE: Refer to specification sheet for full load ampand wire size amp ratingsHeat rejection connection. Fieldsupplied 24V NEC class 2 wiring.Wire connections from evaporator module:1. 24V GND2. 24V Supply3. High Pressure Alarm4. Hot Gas Bypass Connection(only on units with hot gas bypass.If no hot gas bypass, connection isprovided in the evaporator module.Connect wire 4 with wire 2 to the24V supply).64
Split System Models7.5 Centrifugal Air-Cooled Condensing Units7.5.1 Installing the Indoor Condensing UnitRefer to drawings for unit dimensions and component locations.! WARNINGRisk of heavy unit falling from supports. Can cause equipment and building damage, injuryand death.Be sure the supporting roof structure is capable of supporting the weight of the unit(s) andthe accessories during installation and service. (See Table 30 - Indoor centrifugalcondensing unit.)Be sure to securely anchor the top ends of the suspension rods. Make sure all nuts are tight.The indoor condensing unit is usually mounted above the ceiling and must be securely mounted to theroof structure. The ceiling and ceiling supports of existing buildings may require reinforcements. Besure to follow all applicable codes. Use field-supplied threaded suspension rods and 3/8"-16 factoryhardware kit.The indoor condensing unit must be located at the same level or above the Liebert Challenger 3000unit. It must NOT be located below the Liebert Challenger 3000.Recommended clearance between ceiling grids and building structural members is unit height plusthree inches.Install the four field-supplied rods by suspending them from suitable building structural members.Locate the rods so that they will align with the four mounting holes in the flanges that are part of theunit base.Using a suitable lifting device, raise the unit up and pass the threaded rods through the fourmounting holes in the flanges that are part of the unit base.Attach the threaded rods to the unit flanges using the supplied nuts and grommets. (See Figure 35 -Detail of ceiling hanging bracket, Threaded Rod and Hardware Kit Installation). The rubbergrommets provide vibration isolation.1. Use the plain nuts to hold unit in place. Adjust these nuts so that the weight of the unit issupported evenly by the four rods, does not rest on the ceiling grid, and is level.NOTEThe units must be level in order to operate properly.2. Use the Nylock nuts to “jam” the plain nuts.Table 30 Indoor centrifugal condensing unitModel60 Hz 50 HzNet Weightlb (kg)MC_40A MC_39A 240 (109)MC_65A MC_64A 449 (204)65
Page 1:
Precision CoolingFor Business-Criti
Page 5 and 6:
7.5 Centrifugal Air-Cooled Condensi
Page 7 and 8:
IMPORTANT SAFETY INSTRUCTIONSSAVE T
Page 9 and 10:
Introduction1.0 INTRODUCTION1.1 Sys
Page 11 and 12:
Installation (Applicable to all Mod
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20: Installation (Applicable to all Mod
Page 23 and 24: Figure 11 Piping connections for ch
Page 29 and 30: 3.0 AIR-COOLED MODELS—SELF-CONTAI
Page 31 and 32: Air-Cooled Models—Self-Contained
Page 39 and 40: Figure 17 General arrangement—Air
Page 41 and 42: 4.0 WATER-COOLED MODELS—SELF-CONT
Page 43 and 44: Figure 20 General arrangement diagr
Page 45 and 46: Water-Cooled Models—Self-Containe
Page 47 and 48: Glycol/GLYCOOL-Cooled Models—Self
Page 49 and 50: NOTICEGlycol/GLYCOOL-Cooled Models
Page 51 and 52: 5.5.2 Glycol SolutionsGlycol/GLYCOO
Page 57 and 58: Figure 27 General arrangement—GLY
Page 59 and 60: 5.5.4 Motor Ball Valve—Digital Sc
Page 61 and 62: Chilled Water ModelsFigure 30 Chill
Page 63 and 64: 7.2.2 Low VoltageSplit System Model
Page 65 and 66: Split System ModelsTable 24 Line co
Page 67 and 68: Table 26Horizontal air discharge ca
Page 69: Table 28Split System ModelsCabinet
Page 73 and 74: Figure 36 3-ton centrifugal air-coo
Page 75 and 76: Split System ModelsFigure 38 5-ton
Page 77 and 78: Split System ModelsFigure 40 Split
Page 79 and 80: 7.6.4 Glycol SystemsSplit System Mo
Page 81 and 82: Split System ModelsFigure 43 5-ton
Page 83 and 84: R407C Refrigerant8.0 R407C REFRIGER
Page 85 and 86: R407C RefrigerantNOTES79
Page 88: Ensuring The High AvailabilityOf Mi
show all

Liebert Challenger 3000 with iCOM

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?