Liebert Challenger 3000 with iCOM

More documents

Recommendations

Info

Installation (Applicable to all Models)Figure 8Piping connections for water/glycol and GLYCOOL units - Downflow modelsiCOM ControlPanelCondensate Drain3/4" FPTField pitch a minimumof 1/8" (3.2mm) per ft. (305mm).The drain line must comply withall applicable codesHumidifier Water Supply Line1/4" OD CUPIPING OUTLET LOCATIONS(See Cabinet and Floor PlanningDimensional Data for PipingOpening Sizes.)Condenser Supply Line7/8" OD CU on Models BF046WG/BF045WG1-1/8" OD CU on Models BF071WG/BF070WGCondenser Return Line7/8" OD CU on Models BF046WG/BF045WG1-1/8" OD CU on Models BF071WG/BF070WGHot Water Return5/8" OD CU (optional)Hot Water Supply5/8" OD CU (optional)DPN000364Rev. 0114
Installation (Applicable to all Models)Figure 9Piping connections for water/glycol and GLYCOOL units - Upflow modelsPiping outlet locations through the plenumthe same as the unit. See below fordescriptions and connection sizes.Humidifier Water Supply Line1/4" OD CUCondenser Return Line7/8" OD CU on Models BU046WG/BU045WG1-1/8" OD CU on Models BU071WG/BU070WGCondensate Pump Line1/2" OD CUUsed only if optional condensatepump is ordered.Hot Water Return5/8" OD CU (optional)Condenser Supply Line7/8" OD CU on Models BU046WG/BU045WG1-1/8" OD CU on Models BU071WG/BU070WGHot Water Supply5/8" OD CU (optional)Liebert iCOMControlCondensate Drain3/4" FPTField pitch a min. of 1/8" (3.2mm) per ft. (305mm). Units withouta condensate pump have a factory-supplied trap in the unit, so afield trap should not be added. Units with a condensate pump willrequire a field-supplied trap downstream from the pump. Thedrain line must comply with all applicable codes. (If condensatepump is ordered piping is out top of unit).PIPING OUTLET LOCATIONS(See Cabinet and Floor PlanningDimensional Data for PipingOpening Sizes.)DPN000363Rev. 0115
Page 1: Precision CoolingFor Business-Criti
Page 5 and 6: 7.5 Centrifugal Air-Cooled Condensi
Page 7 and 8: IMPORTANT SAFETY INSTRUCTIONSSAVE T
Page 9 and 10: Introduction1.0 INTRODUCTION1.1 Sys
Page 11 and 12: Installation (Applicable to all Mod
Page 19: Installation (Applicable to all Mod
Page 23 and 24: Figure 11 Piping connections for ch
Page 29 and 30: 3.0 AIR-COOLED MODELS—SELF-CONTAI
Page 31 and 32: Air-Cooled Models—Self-Contained
Page 39 and 40: Figure 17 General arrangement—Air
Page 41 and 42: 4.0 WATER-COOLED MODELS—SELF-CONT
Page 43 and 44: Figure 20 General arrangement diagr
Page 45 and 46: Water-Cooled Models—Self-Containe
Page 47 and 48: Glycol/GLYCOOL-Cooled Models—Self
Page 49 and 50: NOTICEGlycol/GLYCOOL-Cooled Models
Page 51 and 52: 5.5.2 Glycol SolutionsGlycol/GLYCOO
Page 57 and 58: Figure 27 General arrangement—GLY
Page 59 and 60: 5.5.4 Motor Ball Valve—Digital Sc
Page 61 and 62: Chilled Water ModelsFigure 30 Chill
Page 63 and 64: 7.2.2 Low VoltageSplit System Model
Page 65 and 66: Split System ModelsTable 24 Line co
Page 67 and 68: Table 26Horizontal air discharge ca
Page 69 and 70: Table 28Split System ModelsCabinet
Page 71 and 72:
Split System Models7.5 Centrifugal
Page 73 and 74:
Figure 36 3-ton centrifugal air-coo
Page 75 and 76:
Split System ModelsFigure 38 5-ton
Page 77 and 78:
Split System ModelsFigure 40 Split
Page 79 and 80:
7.6.4 Glycol SystemsSplit System Mo
Page 81 and 82:
Split System ModelsFigure 43 5-ton
Page 83 and 84:
R407C Refrigerant8.0 R407C REFRIGER
Page 85 and 86:
R407C RefrigerantNOTES79
Page 88:
Ensuring The High AvailabilityOf Mi
show all

Liebert Challenger 3000 with iCOM

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?