Understanding API ICP653 Reading 7-Worksheet-04 Part1

More documents

Recommendations

Info

Notes: 1. Depending on the specific gravity of the content used to determine tmin, Ht may be less than H. Testing the tank to H may yield the corroded area. 2. If Ht is less than H, owner/operator shall determine the consequence and acceptability of operating the tank to H, its maximum design liquid level. Repairs to shell sections above H, shall comply with the requirements of 12.3.2. 3. For reconstructed tanks, St shall be per the current applicable standard. Charlie Chong/ Fion Zhang
Sample problem for maximum allowable fill height of a welded tank shell. What is the hydrostatic test height of a welded tank 112’ diameter, that has a minimum thickness of .115 inches in the first course? (Shell material unknown) (E=1). Ht = SEt/(2.6D) +1 = 26000x .115/(2.6x 112) +1 = 11.26’ Charlie Chong/ Fion Zhang
Page 1 and 2:
Understandings API ICP653 Reading 7
Page 3 and 4:
Charlie Chong/ Fion Zhang
Page 5 and 6: Ctrl + Shift + S = save a copy Ctrl
Page 7 and 8: Charlie Chong/ Fion Zhang Fion Zhan
Page 9 and 10: API 653 Exam Administration -- Publ
Page 11 and 12: • API Recommended Practice 575, I
Page 13 and 14: Charlie Chong/ Fion Zhang
Page 15 and 16: Charlie Chong/ Fion Zhang http://gr
Page 17 and 18: Charlie Chong/ Fion Zhang
Page 19 and 20: 闭门练功 Charlie Chong/ Fion
Page 21 and 22: 1.1 General 1.1.1 This standard cov
Page 23 and 24: 1.4 Safe Working Practices Safety p
Page 25 and 26: c. An owner or operator of one or m
Page 27 and 28: 3.9 critical zone: The portion of t
Page 29 and 30: 3.16 repair organization: An organi
Page 31 and 32: organizations Charlie Chong/ Fion Z
Page 33 and 34: 3.21 as-built standard: The standar
Page 35 and 36: 3.23 major alteration or major repa
Page 37 and 38: g. Removing and replacing part of t
Page 39 and 40: SECTION 4 - SUITABILITY FOR SERVICE
Page 41 and 42: 4.2 Tank Roof Evaluation (General)
Page 43 and 44: 4.2.4 Change of Service 4.2.4.1 Int
Page 45 and 46: 4.3.1.3 Shell corrosion occurs in m
Page 47 and 48: EXAMPLE: A tank 38 feet tall, 150 f
Page 49 and 50: 4.3.3 Minimum Thickness Calculation
Page 51 and 52: G = Highest specific gravity of the
Page 53 and 54: Sample problem for minimum thicknes
Page 55: Maximum Allowable Fill Height Calcu
Page 59 and 60: Joint Efficiency for the plate For
Page 61 and 62: For Riveted Tank E is 1.0 for shell
Page 63 and 64: Table 4.3—Joint Efficiencies for
Page 65 and 66: B. Tank Shells 1. See prior comment
Page 67 and 68: 4.3.6 Flaws cracks and laminations
Page 69 and 70: 4.4 Tank Bottom Evaluation 4.4.1 Ge
Page 71 and 72: 4.4.6 Bottom Measurements Methods (
Page 73 and 74: 4.4.7.4 Critical zone thickness is
Page 75 and 76: 4.4.8 Minimum "t" - Annular Plate R
Page 77 and 78: Quiz: Annular Plate t min Annular p
Page 79 and 80: API653: Table 4.5—Annular Bottom
Page 81 and 82: API653: Table 4.4—Bottom Plate Mi
Page 83 and 84: 4.5.2 and 4.5.3 General a. For repa
Page 85 and 86: 5.2.1 Reported conditions involving
Page 87 and 88: 5.3 Assessment Procedure 5.3.1 - 5.
Page 89 and 90: 6.2.2 The interval between inspecti
Page 91 and 92: 6.3.3 In-service UT "t" measurement
Page 93 and 94: API651: 11.3 Cathodic Protection Su
Page 95 and 96: CP Survey 11.3 Cathodic Protection
Page 97 and 98: 6.4.2 Inspection Intervals 6.4.2.1
Page 99 and 100: 6.4.2.1.2 As an alternative to esta
Page 101 and 102: 6.4.2.2 Subsequent Internal Inspect
Page 103 and 104: Table 4.4—Bottom Plate Minimum Th
Page 105 and 106: Quiz: Critical Zone t min t minimum
Page 107 and 108:
Quiz: Bottom Plate excluding Critic
Page 109 and 110:
6.8.2 Construction Records May incl
Page 111 and 112:
6.9 Reports 6.9.1 Recommended repai
Page 113 and 114:
113 Inspection Frequency Considerat
Page 115 and 116:
115 Internal inspection is required
Page 117 and 118:
API 653 Initial Inspection Interval
Page 119 and 120:
119 API 653 Initial Inspection Inte
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
125 API 653 Subsequent Inspection I
Page 127 and 128:
Page 129 and 130:
129 Steps for corrosion rate calcul
Page 131 and 132:
131 Finally ‐ Calculate Subsequen
Page 133 and 134:
API 653 Subsequent Inspection Inter
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
139 Factors to Consider in a RBI As
Page 141 and 142:
141 RBI Inspection • RBI Assessme
Page 143 and 144:
143 Comparison Direct Measurements
Page 145 and 146:
145 Questions ?
Page 147 and 148:
7.3.1.2 If plates are not identifie
Page 149 and 150:
8.5 Shell Penetrations 8.5.1 New/re
Page 151 and 152:
9.2 Removal and Replacement - Shell
Page 153 and 154:
9.2.3 Weld Joint Design 9.2.3.1 Rep
Page 155 and 156:
9.3.1.7 Maximum size of lap patch p
Page 157 and 158:
9.3.3 Lapped patch plates may be us
Page 159 and 160:
9.7 Repair of Shell Penetrations 9.
Page 161 and 162:
9.10 Repair of Tank Bottoms (Defini
Page 163 and 164:
9.10.2.2 New bearing plates are req
Page 165 and 166:
9.10.3.1 Additional Welded-on Plate
Page 167 and 168:
9.13 Repair/Replacement of Floating
Page 169 and 170:
9.14.5 Installation Procedure 9.14.
Page 171 and 172:
Hot Tapping Charlie Chong/ Fion Zha
Page 173 and 174:
10.3.2 Bottoms 10.3.2.1 Deseam lapw
Page 175 and 176:
10.3.5 Piece Marking 10.3.5.1 Shell
Page 177 and 178:
10.4.2.3 Specific welding notes: a.
Page 179 and 180:
10.4.3 Bottoms 10.4.3.2 Weld shell
Page 181 and 182:
SECTION 11 - WELDING 11.1 Welding Q
Page 183 and 184:
12.1.2 Shell Penetrations 12.1.2.1
Page 185 and 186:
12.1.6 Shell-to Bottom 12.1.6.1 Joi
Page 187 and 188:
12.2.1.4 Each butt-weld annular pla
Page 189 and 190:
12.3.2.2 Shell Repair 12.3.2.2.1 We
Page 191 and 192:
12.5 Measured Settlement (During Hy
Page 193 and 194:
SECTION 13 - MARKING AND RECORD KEE
Page 195 and 196:
13.3 Certification Documentation of
Page 197 and 198:
ANS: ANS: Charlie Chong/ Fion Zhang
Page 199 and 200:
B.2.2.3 Differential Settlement (ou
Page 201 and 202:
B.2.3 Edge settlement B.2.3.1 Occur
Page 203 and 204:
APPENDIX C CHECKLISTS FOR TANK INSP
Page 205 and 206:
APPENDIX E TECHNICAL INQUIRIES This
Page 207 and 208:
G.2.6 qualification test: The demon
Page 209 and 210:
G.3 An explanation of Tank Bottom E
Page 211 and 212:
API 653 CODE QUIZ Charlie Chong/ Fi
Page 213 and 214:
Q3. A condition that exists when it
Page 215 and 216:
Q7. What primary factor determines
Page 217 and 218:
Q11. What type of contour cut (if a
Page 219 and 220:
Q15. API-653 (Section 12) requires
Page 221 and 222:
Q16. Calculate the minimum thicknes
Page 223 and 224:
Q19. A bulge is found on the tank f
Page 225 and 226:
Q16. d (1/2") [Paragraph 4.3.3 page
Page 227 and 228:
Section 2 650 Summary 2007 Charlie
Page 229 and 230:
Charlie Chong/ Fion Zhang
Page 231 and 232:
Good Luck! Charlie Chong/ Fion Zhan
show all

Understanding API ICP653 Reading 7-Worksheet-04 Part1

Create successful ePaper yourself

Delete template?

Save as template?