Dunkermotoren Motors Gearboxes and Controllers

More documents

Recommendations

Info

BGE 42 | 3004 A, Controller for BG 32 | BG 42/ Regelektroniken für BG 32 | BG 42 » There is an integrated potentiometer for setting the speed » Two connection leads can be used to provide both a start/ stop and a clockwise/ counter-clockwise function » By supplying an analog target voltage in the range 0...+10 V, the speed of rotation can be set in a range from 500 rpm to 5000 rpm » Lower speeds, down to ca. 200 rpm, are possible where less smooth rotation can be tolerated » Various protection functions, such as low-voltage cut-off, reversepolarity protection, over-temperature cut-off, and stall protection, guarantee high operational reliability » A signal with 4 pulses (2x 2 pulses) per revolution generated from the integrated Hall sensors will be provided » Die Drehzahl kann über ein integriertes Potentiometer fest vorgegeben werden » Über zwei Anschlusslitzen kann sowohl eine Start/ Stopp- als auch eine Rechts/ Links-Umschaltung erfolgen » Durch Vorgabe einer analogen Sollwertspannung von 0...+10 V kann die Drehzahl im Bereich von 500 rpm bis 5000 rpm eingestellt werden » Kleinere Drehzahlen bis ca. 200 rpm sind mit eingeschränkter Rundlaufgenauigkeit möglich » Verschiedene Schutzeinrichtungen wie Unterspannungsabschaltung, Verpolschutz, Übertemperaturabschaltung und Blockierschutz garantieren eine hohe Betriebssicherheit » Ein Signal mit 4 Pulsen (2x 2 Pulse) pro Umdrehung, generiert von den integrierten Hall Sensoren, wird ausgegeben Please note: The connection between motor and electronics must be as short as possible. The maximum length of the connection cable should be not longer than 2m. For avoiding of any failures it is recommended to use a separated cable routing for phase and sensor. (Please note that, for the BGE 3004 A, the matching motor connector must also be ordered.) Hinweis: Die Verbindung ist zwischen Motor und Elektronik möglichst kurz zu halten. Die maximale Länge der Motoranschlussleitung sollte 2m nicht überschreiten. Zur Vermeidung von Störungen empfiehlt sich eine getrennte Kabelführung von Phasenleitungen und Sensorleitungen. (Bitte beachten Sie, dass bei der BGE 3004 A der Gegenstecker zum Motor mitbestellt werden muss.) 2 1 1 12-40 IO mode Speed mode Block commutation Digital inputs Digital outputs Analog inputs Supply voltage versions Data/ Technische Daten BGE 42 BGE 3004 A Design/ Bauart attached/ angebaut external/ extern Operating voltage/ Betriebsspannung VDC 12 ... 40 12 ... 40 Voltage range/ Max. zulässiger Spannungsbereich VDC 11.2 ... 44 11.2 ... 44 Continuous current/ Max. zulässiger Dauerstrom A 4* 4* Peak current/ Max. zulässiger Spitzenstrom A 34 34 Ambient temperature/ Umgebungstemperatur °C -10 ... +40 -10 ... +40 Weight/ Gewicht kg 0.04 0.04 * 20°C 32 kHz PWM BGE 42/3004A Controller / Regelelektroniken Dimensions in mm BGE Dimensions 42 for BG in mm 42/ BGE Maßzeichnung 42 / Maßzeichnung in mm in BGE mm 42 BGE für 42BG 42 BG 42 3.5±0.5 36.8±1 Colour/ Farbe Signal red + black - yellow R/L green Start/ Stop brown n grey Hall 5 +1 verzinnt 300±30 ab Motor 55±0.8 40±0.5 Pin assignment / Pinbelegung Colour / Farbe Signal Colour / Farbe Signal red + green Start/Stop black - brown n yellow R/L grey Hall Dimensions in mm BGE 3004A / Maßzeichnung in mm BGE 3004A 176 | Visit www.dunkermotoren.com for further product information/ Besuchen Sie www.dunkermotoren.de für weitere Produktinformationen 300 ±30 Ø2.79
Dimensions in mm BGE 3004 A for BG 32 | BG 42/ Maßzeichnung in mm BGE 3004 A für BG 32 | BG 42 Colour/ Farbe black red yellow green brown grey Signal GND +V C r / l start / stop N-analog Hall Lead length/ Litzenlänge 300 mm (Plug see accessories/ Anschlussstecker siehe Zubehör) Colour/ Farbe blue white orange black yellow green brown red Signal B A C GND (Hall) H1 H2 H3 +V C (Hall) Controller ■ Preferred series/ Vorzugsreihe ■ Standard product/ Standardprodukt ■ On request/ auf Anfrage See notes page 8/ Hinweise siehe S. 8 Visit www.dunkermotoren.com for further product information/ Besuchen Sie www.dunkermotoren.de für weitere Produktinformationen | 177
Page 1:
BG 75 dPro PN/EC/EI Preliminary Ver
Page 4 and 5:
Who we are/ Wer wir sind Dunkermoto
Page 6 and 7:
Motion control 4.0/ Motion Control
Page 8 and 9:
Product classification/ Produktklas
Page 10 and 11:
GR/G brush type DC/ GR/G-Bürstenbe
Page 12 and 13:
BG brushless DC/ BG-Bürstenlose Gl
Page 14 and 15:
KD/DR AC motors/ KD/DR-Wechsel- Dre
Page 16 and 17:
CASM electric cylinders/ CASM-Elekt
Page 18 and 19:
Operating modes/ Betriebsarten dMov
Page 20 and 21:
Software/ Software Drive Assistant
Page 22 and 23:
Software/ Software Positioning modu
Page 24 and 25:
Software/ Software MotionCode Progr
Page 26 and 27:
Technical information/ Technische I
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Handbook for selection of motors/ F
Page 34 and 35:
Brushed DC motors » Series GR/G Th
Page 36 and 37:
G 30.2 | cont. 4 W, peak 5 W » Mec
Page 38 and 39:
G 30.1 | G 30.1S | cont. 7 W, peak
Page 40 and 41:
G 30.1 | G 30.1S | cont. 7 W, peak
Page 42 and 43:
G 30.0 | G 30.0S | cont. 10 W, peak
Page 44 and 45:
GR 42x25 | cont. 15 W, peak 25 W »
Page 46 and 47:
GR 42x40 | cont. 21 W, peak 38 W »
Page 48 and 49:
GR 53x30 | cont. 39 W, peak 81 W »
Page 50 and 51:
GR 53x58 | cont. 61 W, peak 136 W
Page 52 and 53:
GR 63x25 | cont. 50 W, peak 119 W
Page 54 and 55:
GR 63x55 | cont. 99 W, peak 286 W
Page 56 and 57:
GR 63Sx55 | cont. 126 W, peak 368 W
Page 58 and 59:
GR 80x40 | cont. 128 W, peak 370 W
Page 60 and 61:
GR 80x80 | cont. 221 W, peak 851 W
Page 62 and 63:
Brushless DC motors » Series BG Th
Page 64 and 65:
Overview motors/ Übersicht Motoren
Page 66 and 67:
BGA 22 dCore, 8 - 24 Watt » 3-phas
Page 68 and 69:
BG 32 dCore | cont. 20 W, peak 27 W
Page 70 and 71:
BG 42 dCore | cont. 64 W, peak 156
Page 72 and 73:
BG 45 | cont. 80 W, peak 168 W » H
Page 74 and 75:
Page 76 and 77:
BG 65 | cont. 120 W, peak 260 W »
Page 78 and 79:
BG 65S | cont. 186 W, peak 470 W »
Page 80 and 81:
BG 75 | cont. 530 W, peak 1150 W »
Page 82 and 83:
Page 84 and 85:
BGA 22 dGo BG 32 KI BG 42 KI 2-wire
Page 86 and 87:
BGA 22 dGo, 8 - 24 Watt » 3-phase
Page 88 and 89:
BG 32 KI | cont. 20 W, peak 30.5 W
Page 90 and 91:
BG 42 KI | cont. 64 W, peak 110 W
Page 92 and 93:
BG 45 SI BG 45 PI/MI BG 45 CI/PB/EC
Page 94 and 95:
BG 45 SI | cont. 74 W, peak 122 W
Page 96 and 97:
BG 45 CI/PB/EC | cont. 91 W, peak 1
Page 98 and 99:
BG 45 CI/PB/EC | cont. 91 W, peak 1
Page 100 and 101:
BG 45 PI/MI | cont. 91 W, peak 159
Page 102 and 103:
BG 65 dMove | cont. 274 W, peak 327
Page 104 and 105:
BG 66 dMove | cont. 274 W, peak 327
Page 106 and 107:
BG 66 dPro CO/IO | cont. 270 W, pea
Page 108 and 109:
BG 66 dPro PN/EC/EI | cont. 270 W,
Page 110 and 111:
BG 75 dPro CO/IO | cont. 450 W, pea
Page 112 and 113:
Page 114 and 115:
BG 95 dPro CO/IO | cont. 1100 W, pe
Page 116 and 117:
Page 118 and 119:
AC motors » Series KD/DR Dunkermot
Page 120 and 121:
KD/DR 52.1-2, 20 - 22 Watt » Rugge
Page 122 and 123:
KD/DR 62.1-2, 34 - 44 Watt » Rugge
Page 124 and 125:
KD/DR 52.1-4 | 62.1-4, 5 - 15 Watt
Page 126 and 127: KD/DR 52.0-2, 25 - 30 Watt » Rugge
Page 132 and 133: Linear products » Series ST | CASM
Page 134 and 135: ST 11 | cont. 19 N, peak 91 N » In
Page 136 and 137: SCA 11 with integrated amplifier |
Page 138 and 139: ST 25 | cont. 90 N, peak 780 N » I
Page 140 and 141: XTR 25 | cont. 108 N, peak 860 N »
Page 142 and 143: XT 38 | cont. 255 N, peak 1860 N »
Page 144 and 145: Servo Tube SA/ SC 38 | cont. 615 N,
Page 146 and 147: Accessories/ Zubehör Brake for STA
Page 148 and 149: Accessories/ Zubehör DME 230x4 »
Page 150 and 151: SM 11 | cont. 19 N, peak 92 N » Se
Page 152 and 153: SM 25 | cont. 90 N, peak 780 N » S
Page 154 and 155: XM 38 | cont. 255 N, peak 1860 N »
Page 156 and 157: LSM 06 | cont. 39 N, peak 200 N »
Page 158 and 159: LSM 13 | cont. 324 N, peak 680 N »
Page 160 and 161: LSG 13 | PLG 52 | cont. 457 N, peak
Page 162 and 163: LSG 13 | SG 62/ 80K | cont. 650 N,
Page 164 and 165: CAHB2M/L | cont. 10.000 N, peak 10.
Page 166 and 167: CASM-32 | cont. 327 N, peak 700 N
Page 172 and 173: CASM-32 CASM-32 Accessories/ Access
Page 174 and 175: Controllers » Series BGE External
Page 178 and 179: BGE 5510 dPro CO/IO » Compact 4-qu
Page 180 and 181: BGE 5510 dPro PN/EC/EI » Compact 4
Page 182 and 183: BGE 6005 A » Very compact 4-quadra
Page 184 and 185: BGE 6010 A | BGE 6015 A » Very com
Page 186 and 187: BGE 6060 A » Compact 4-quadrant co
Page 188 and 189: DME 230x4 » Digital servocontrolle
Page 190 and 191: DME 400x8 » Digital servocontrolle
Page 192 and 193: Gearboxes/ Getriebe » Series/ Baur
Page 194 and 195: PLG 22 HT » Compact high torque pl
Page 196 and 197: PLG 32 » Compact, industry compati
Page 198 and 199: PLG 40 LB » Low backlash servo pla
Page 200 and 201: PLG 42 S » Compact, industry compa
Page 202 and 203: PLG 52 H » High efficiency » Quie
Page 206 and 207: PLG 63 EP » Industry compatible pl
Page 208 and 209: PLG 63 HT » Industry compatible hi
Page 210 and 211: PLG 75 EP » Industry compatible pl
Page 218 and 219: KG 90 » Bevel gearbox with planeta
Page 220 and 221: SG 45 » Housing made of high-tensi
Page 222 and 223: SG 65 » Housing made of high-tensi
Page 224 and 225: SG 85 » Combination with GR 53 and
Page 226 and 227:
SG 120 | SG 120 H | SG 120 K Dimens
Page 228 and 229:
Brakes Brushless motors series BG a
Page 230 and 231:
Brakes/ Bremsen The brakes can be m
Page 232 and 233:
Incremental Encoders/ Inkrementalge
Page 234 and 235:
Absolute encoder/ Absolutwertgeber
Page 236 and 237:
Accessories/ Zubehör | GR Our acce
Page 238 and 239:
Accessories/ Zubehör | BG/BGE BG 3
Page 240 and 241:
Accessories/ Zubehör | BG/BGE 5 Co
Page 242 and 243:
Accessories/ Zubehör | BG/BGE 11 C
Page 244 and 245:
Accessories/ Zubehör | BG/BGE 19 C
Page 246 and 247:
Software/ Software 21 Starter Kit f
Page 250:
Social icon Rounded square Only use
show all

Dunkermotoren Motors Gearboxes and Controllers

Create successful ePaper yourself

Delete template?

Save as template?