SUNNY WEBBOX - User Manual - SMA Solar Technology AG

More documents

Recommendations

Info

Service Functions SMA Solar Technology AG Resetting the Sunny WebBox via the User Interface 1. Log into the Sunny WebBox as an installer. 2. Select "WebBox > Info" on the user interface. 3. Select "Factory settings". ☑ A window containing a security question opens. 4. Click [Confirm]. ☑ The Sunny WebBox is now reset to its factory settings and switches off the Web server. 5. If the "POWER" LED is green and all other LEDs are red, disconnect the plug-in power supply from the power outlet. 6. Wait 15 seconds. 7. Reconnect the plug-in power supply to the power outlet. ☑ The Sunny WebBox will now start with the factory settings. Resetting the Sunny WebBox via the Reset Button Beginning with Sunny WebBox version E1, the hole for the Reset button is found on the rear panel of the Sunny WebBox under the upper left foot. Only press the reset button when the Sunny WebBox is switched on. 1. If the Sunny WebBox is mounted on a top-hat rail, remove it from the top-hat rail. If the Sunny WebBox is mounted directly to a wall, push the Sunny WebBox upwards slightly and remove the Sunny WebBox from the top hat rail. Resetting specific Sunny WebBox settings. Depending on how long you press the Reset button, the Sunny WebBox performs the actions listed in the following table. Time Action 1 − 5 seconds Resetting the passwords to the factory setting. All other settings (event memory, network settings, modem settings, and portal settings) will remain intact. 5 − 15 seconds Resetting the network settings to the factory setting. All other settings (event memory, modem settings, portal settings and passwords) will remain intact. 15 − 30 seconds Resets all settings (event memory, network settings, modem settings, Sunny Portal settings and passwords) of the Sunny WebBox to the default values. The Sunny WebBox deletes the plant data and plant settings completely. 76 SWebBox-BEN111033 User Manual
SMA Solar Technology AG Service Functions 2. Insert a pointed object (such as a paper clip) into the hole and press the reset button. ☑ The Sunny WebBox is now reset. 11.6 Deleting Device Descriptions 1. Log into the Sunny WebBox as an installer. 2. Select "WebBox > Info" on the user interface. 3. Select [Delete device descriptions]. ☑ The unit descriptions of all devices will be erased. When the Sunny WebBox is restarted, all unit descriptions will be detected again automatically. User Manual SWebBox-BEN111033 77
Page 1:
Device for Plant Monitoring SUNNY W
Page 4 and 5:
Table of Contents SMA Solar Technol
Page 6 and 7:
Table of Contents SMA Solar Technol
Page 8 and 9:
SMA Solar Technology AG 8 SWebBox-B
Page 10 and 11:
Information on this Manual SMA Sola
Page 12 and 13:
Sunny WebBox SMA Solar Technology A
Page 14 and 15:
Safety SMA Solar Technology AG 3.2
Page 16 and 17:
Unpacking SMA Solar Technology AG I
Page 18 and 19:
Device Overview SMA Solar Technolog
Page 20 and 21:
Commissioning SMA Solar Technology
Page 22 and 23:
Page 24 and 25:
Page 26 and 27: Commissioning SMA Solar Technology
Page 44 and 45: Logging in and out of the Sunny Web
Page 46 and 47: Operation SMA Solar Technology AG 8
Page 48 and 49: Operation SMA Solar Technology AG 8
Page 50 and 51: Managing Plant Data SMA Solar Techn
Page 60 and 61: Settings SMA Solar Technology AG 10
Page 64 and 65: Settings SMA Solar Technology AG 3.
Page 72 and 73: Service Functions SMA Solar Technol
Page 74 and 75: Service Functions SMA Solar Technol
Page 78 and 79: Maintenance and Care SMA Solar Tech
Page 80 and 81: Troubleshooting SMA Solar Technolog
Page 86 and 87: Appendix SMA Solar Technology AG 15
Page 92 and 93: Appendix SMA Solar Technology AG 4.
Page 94 and 95: Appendix SMA Solar Technology AG Es
Page 96 and 97: Technical Data SMA Solar Technology
Page 98 and 99: Contact SMA Solar Technology AG 18
Page 100: ��
show all

SUNNY WEBBOX - User Manual - SMA Solar Technology AG

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?