ProMatic - Hormann.fr

ENGLISHLED:Cause:Elimination:Note:Acknowledgement:LED:06.2004 TR10A014 REflashes 2 x in 4 secondsA photocell or closing edge safety device connectedto terminals 20 and 74 has been interruptedor activated. It is possible that a safetyreturn has been initiated.Remove the obstruction in question, check thephotocell and / or closing edge safety device,and if necessary replace.If no photocell or closing edge safety device isconnected to terminals 20 and 74, check whetherthe factory assembled resistance of 8,2 kΩ betweenterminals 20 and 74 is present – if necessaryconnect.Another impulse is generated via an externalbutton, the remote control or the transparentbutton – the door travels in the opposite directionto that last travelled.flashes 3 x in 5 secondsLED:Cause:Elimination:Cause: The CLOSE force limit has been activated –the door has carried out a safety return.Elimination: Remove the obstruction. If a safety return hastaken place for no recognisable reason, checkthe door mechanics. It may be necessary todelete the door data and reprogramme.Acknowledgement:Another impulse is generated via an externalbutton, the remote control or the transparentbutton – the door opens.Acknowledgement:LED:flashes 4 x in 6 secondsThe STOP or emergency-OFF circuit is openor was opened during a travel cycle (seesection 3.5.3)Close the STOP or emergency-OFF circuit(see section 3.5.3)Another impulse is generated via an externalbutton, the remote control or the transparentbutton – the door travels in the opposite directionto that last travelled.flashes 5 x in 7 secondsLED:Cause:flashes 6 x in 8 secondsOperator faultElimination:Cause: The OPEN force limit has been activated –the door has stopped whilst opening.Elimination: Remove the obstruction. If the door has cometo a halt for no recognisable reason, check thedoor mechanics. It may be necessary to deletethe door data and reprogramme.Acknowledgement:Another impulse is generated via an externalbutton, the remote control or the transparentbutton – the door closes.Acknowledgement:LED:Cause:Elimination/Acknowledgement:LED:Cause:Elimination/Acknowledgement:Note:It may be necessary to delete the door data. Ifthe operator fault re- occurs, replace the operator.Generate an impulse via an external button,the remote control or the transparent button –the door opens (OPEN reference cycle).flashes 7 x in 9 secondsThe operator has not yet been programmed(this is merely being pointed out – it is not afault/error).Initiate learn operation for the CLOSE directionvia the transparent button.flashes 8 x in 10 secondsThe operator requires a reference cycle (this ismerely being pointed out – it is not a fault/error).Initiate a reference cycle in the OPEN directionvia an external button, the remote control orthe transparent button.This is the normal state following a power failurewhen no door data is stored or this has beendeleted and/or the last door position is notsufficiently well known.4 Terms and Conditions of the WarrantyGuarantee PeriodIn addition to the statutory guarantee provided by thedealer, we provide the following guarantee of parts fromthe date of purchase:a) 5 years on operator mechanics, motor and motorcontrolsb) 2 years on radio, impulse generators, accessoriesand special systemsThere is no guarantee on consumables (e.g. fuses,batteries, lighting devices).Claims made under the guarantee do not extend theguarantee period. Following the supply of replacementparts the guarantee period is six months; or at least,the remainder of the guarantee period.ConditionsA claim under this guarantee is only valid for the countryin which the equipment was bought. The product musthave been purchased through authorised distributionchannels. A claim under this guarantee exists only fordamage to the product in the contract itself. Reimbursementof expenditure for dismantling and installation,testing of corresponding parts, as well as demands forlost profits and compensation for damages, are excludedfrom the guarantee. The receipt of purchase substantiatesyour right to claim under the guarantee. ➤43