Bedienungsanleitung KXE - REITZ Ventilatoren

More documents

Recommendations

Info

7.6 Marking, information sign Figure 15 7.7 Waste disposal 7.8 Revison BWA-<strong>KXE</strong>-Fetteinzelstehlager_englisch_02.doc The marking / information signs must be: - cleaned with a rag, - checked for tight fastening and legibility. Maintenance Legend: 1 name plate 2 sense of rotation arrow 3 warning notice inspection opening (optional) 4 sign “Maintenance of the bearings” 5 motor nameplate 6 earthing clamps (optional) 7 sign “danger symbols with explanations” 8 sign “Read operation manual” 9 sign “Attention – do not weld” Figure 15 � Example for markings Collect used oil, used grease or cleaning rags / wool contaminated with oil / grease in containers correspondingly marked and dispose of them in a safe manner consistent with all applicable regulations and in an environmentally compatible way. In general, half-yearly up to yearly revision intervals should be sufficient under the conditions that: - all checks in the course of the commissioning / start-up and the maintenance works were carried out properly and in due time, and - each serious constitutional change that were recognized by the continuous operation monitoring has been systematically investigated and repaired. 7.8
7.9 Maintenance schedule BWA-<strong>KXE</strong>-Fetteinzelstehlager_englisch_02.doc Maintenance Structural component Daily Weekly Quarterly Yearly impeller An inspection of the impeller must be carried out immediately, if � the permissible limiting values (see chapter 9.1.2 Limiting values vibrations) are exceeded, � changed impeller noises occur. Examine the impeller every 5,000 operating hours and check it for alteration (cracks, geometric alterations, balancing condition, wear and sticking material), but at least once a year. Check the impeller e.g. by non-destructive crack testing. Fans that are subject to high dynamical stresses are to be checked in accordance with the additional agreement (maintenance schedule) within the prescribed intervals. bearings An inspection of the bearings must be carried out immediately, if � the permissible limiting values (see chapter 9.1.2 Limiting values vibrations and 9.1.3 Limiting values bearing temperatures) are exceeded, � changed running noises occur � unusual alterations of the lubricant occur. Re-lubrification intervals acc. to plate “Maintenance of the bearings” (see chapt. 7.3.1.2 Lubrication intervals) shaft seal The shaft sealing rings have to be checked and exchanged if the sealing gas consumption or leakage increases. Exchange the shaft seal ring when the rings are worn or damaged. If the seal ring consists of more than one part, replace the full seal ring set. shaft earthing Check the correct functioning of the shaft earthing regularly and in dependence of the operating conditions and replace it, if required. condensate drain Drain the accumulated condense water in regular intervals or when required in a suitable drain receptacle and dispose of it in an environmentally compatible way. coupling If noise levels are changed abruptly and / or vibrations occur abruptly, the coupling must be checked and if required, it must be re-aligned or exchanged. motor pay attention to retighten screws, check motor, if running noises and check bearings required, exchange quiet running, bearings, observe remove sticking maintenance material (e.g. dust), instructions of if required motor manufacturer earthing motor clean inside, clean inside, terminal box tighten screws tighten screws connections for collect measuring check for functiona- check for functiona- check for functiona- monitoring devices and auxiliary equipment values litylitylity flexible connections check at regular intervals and – if check, if required, check, if required, required – after change of the processes. retighten screws retighten screws and if worn-out, and, if worn out, exchange flexible exchange flexible connections connections total fan pay attention to pay attention to check impeller, fan operational noises operational noises bearings and motor and quiet running and quiet running bearings, shaft seal, coupling and flexible connections for wear and, if required, repair or exchange them 7.9
Page 1 and 2:
Translation of the Original instruc
Page 3 and 4:
Table of contents Table of contents
Page 5 and 6: BWA-KXE-Fetteinzelstehlager_englisc
Page 7 and 8: 1.3 Description 1.4 Intended use BW
Page 9 and 10: 1.6 General remarks BWA-KXE-Fettein
Page 11 and 12: 1.7 Nameplate BWA-KXE-Fetteinzelste
Page 13 and 14: 2.3 Symbols BWA-KXE-Fetteinzelstehl
Page 15 and 16: 2.4 Safety regulations BWA-KXE-Fett
Page 17 and 18: 2.6 Electric connection conditions
Page 19 and 20: 2.9 Personal protective equipment B
Page 21 and 22: 3. Transport, Installation 3.1 Gene
Page 25 and 26: 3.5 Transport BWA-KXE-Fetteinzelste
Page 27 and 28: 3.6 Installation BWA-KXE-Fetteinzel
Page 29 and 30: 3.6.4 Mounting and Alignment 3.6.4.
Page 31 and 32: 3.6.4.3 Alignment of the shafts Fig
Page 35 and 36: 3.7.3 Ducting of fan 3.7.4 Check of
Page 37 and 38: 3.7.7 Electric connection condition
Page 39 and 40: 3.7.9 Seal connection BWA-KXE-Fette
Page 41 and 42: 4.3.2 Check of sense of rotation
Page 43 and 44: 4.4.3 Switching on of the fan BWA-K
Page 45 and 46: 5. Operation, Operating 5.1 General
Page 47 and 48: 6.3 Troubles BWA-KXE-Fetteinzelsteh
Page 49 and 50: 7. Maintenance BWA-KXE-Fetteinzelst
Page 51 and 52: 7.3.1.1 Lubrication instructions an
Page 53 and 54: 7.4 Shaft seal 7.4.1 Standard seal
Page 55: 7.5 Coupling 7.5.1 Alignment Figure
Page 59 and 60: 8. Repair work 8.1 General remarks
Page 61 and 62: 9. Annex 9.1 Additional technical i
Page 63 and 64: 9.1.3 Limiting values bearing tempe
Page 65 and 66: 10. Fan shutdown 10.1 General remar
Page 67 and 68: 10.4 Measures in case of recommissi
show all

Bedienungsanleitung KXE - REITZ Ventilatoren

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?