Bedienungsanleitung KXE - REITZ Ventilatoren

More documents

Recommendations

Info

10.3 Measures in case of prolonged shutdown BWA-<strong>KXE</strong>-Fetteinzelstehlager_englisch_02.doc Fan shutdown When the fan is put out of operation for more than three months the following steps must be taken: - Drive motors and actuators If there are drains, please open them, drain the accumulated water and re-close the openings. Check the terminal box connections for tight screwing. - Protect all bright parts (especially fan shaft and coupling) from corrosion. - for single-bearing housings (fan shaft bearings) press in grease until fresh grease leaks out from the discharge bore and turn the shaft manually several times The grease type that was filled in and the relubrication grease type are indicated on the bearing plate (“Maintenance of bearings”. Do not use another grease type. Note on the time period of the fan shutdown: If the fan is taken out of operation for a period of more than twelve months, check the grease for deoiling or contamination (if condensate water intrudes in the grease, it will change its consistency). The grease has to be exchanged if it is de-oiled or contaminated. 10.2
10.4 Measures in case of recommissioning BWA-<strong>KXE</strong>-Fetteinzelstehlager_englisch_02.doc Carry out the following steps: Fan shutdown - Check the bearings and shaft seals for tightness - Check whether the operating materials like oil or grease have been filled in properly, re-fill or re-grease if necessary or exchange the consumables - Check the V-belts for damage, cracks, ruptures, embrittlement - Check drives and actuators for condensate water in the terminal box and housing, if necessary, drain the water and dry the interior. - Remove the anti-corrosion coating from all bright parts which could affect the functioning (e.g. shaft seal, shaft earthing) It is not permitted to employ damaged or corroded parts or such parts that are unfit for operation. Prior to a new start-up, chapter 4 Start-up must be observed. 10.3
Page 1 and 2:
Translation of the Original instruc
Page 3 and 4:
Table of contents Table of contents
Page 5 and 6:
BWA-KXE-Fetteinzelstehlager_englisc
Page 7 and 8:
1.3 Description 1.4 Intended use BW
Page 9 and 10:
1.6 General remarks BWA-KXE-Fettein
Page 11 and 12:
1.7 Nameplate BWA-KXE-Fetteinzelste
Page 13 and 14:
2.3 Symbols BWA-KXE-Fetteinzelstehl
Page 15 and 16: 2.4 Safety regulations BWA-KXE-Fett
Page 17 and 18: 2.6 Electric connection conditions
Page 19 and 20: 2.9 Personal protective equipment B
Page 21 and 22: 3. Transport, Installation 3.1 Gene
Page 23 and 24: BWA-KXE-Fetteinzelstehlager_englisc
Page 25 and 26: 3.5 Transport BWA-KXE-Fetteinzelste
Page 27 and 28: 3.6 Installation BWA-KXE-Fetteinzel
Page 29 and 30: 3.6.4 Mounting and Alignment 3.6.4.
Page 31 and 32: 3.6.4.3 Alignment of the shafts Fig
Page 35 and 36: 3.7.3 Ducting of fan 3.7.4 Check of
Page 37 and 38: 3.7.7 Electric connection condition
Page 39 and 40: 3.7.9 Seal connection BWA-KXE-Fette
Page 41 and 42: 4.3.2 Check of sense of rotation
Page 43 and 44: 4.4.3 Switching on of the fan BWA-K
Page 45 and 46: 5. Operation, Operating 5.1 General
Page 47 and 48: 6.3 Troubles BWA-KXE-Fetteinzelsteh
Page 49 and 50: 7. Maintenance BWA-KXE-Fetteinzelst
Page 51 and 52: 7.3.1.1 Lubrication instructions an
Page 53 and 54: 7.4 Shaft seal 7.4.1 Standard seal
Page 55 and 56: 7.5 Coupling 7.5.1 Alignment Figure
Page 57 and 58: 7.9 Maintenance schedule BWA-KXE-Fe
Page 59 and 60: 8. Repair work 8.1 General remarks
Page 61 and 62: 9. Annex 9.1 Additional technical i
Page 63 and 64: 9.1.3 Limiting values bearing tempe
Page 65: 10. Fan shutdown 10.1 General remar
show all

Bedienungsanleitung KXE - REITZ Ventilatoren

Create successful ePaper yourself

Delete template?

Save as template?