Power Cable Accessories
Power Cable Accessories
Power Cable Accessories
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
RSTI – Screened, separable T-connection system for gas-insulated switchgear with<br />
bushings according to EN 50181 type C (400/630A), 10 kV, 15 kV, 20 kV and 35 kV<br />
Raychem screened separable connectors<br />
are designed to connect single-core<br />
polymeric insulated cables to gasinsulated<br />
switchgear or other equipment<br />
with bushings according to EN 50181<br />
type C up to 42 kV. Connections can be<br />
made in a right-angle configuration, also<br />
for 2 or 3 cables in parallel, such<br />
configurations require mechanical fixing<br />
of each cable in the switchgear.<br />
For connections to 1250 A rated bushings<br />
with profile according to EN 505181 type<br />
C, parallel connections are possible with<br />
each RSTI rated for max. 630A.<br />
Made of a highly modified silicone rubber<br />
and protected with a thick wall moulded<br />
outer conductive shield connected to<br />
earth, Raychem screened connectors<br />
RSTI are thus suitable for both indoor and<br />
outdoor installations. Oversheath testing<br />
can be performed without removal of the<br />
screened connector<br />
The modern design and material selection<br />
in combination with the Raychem<br />
designed high performance mechanical<br />
lug allows a large application range,<br />
covering most common cable sizes with<br />
just one kit.<br />
The overall and cut back dimensions are<br />
designed for use of minimum space<br />
required in the termination box, even<br />
double connections fit within most<br />
standard boxes.<br />
Raychem screened connectors RSTI are<br />
equipped with a capacitive test point to<br />
determine if the circuit is energised. The<br />
capacitive test point is protected by a<br />
conductive cap.<br />
The screened cable connector<br />
exceeds the requirements of<br />
CENELEC HD 629.1 S1 which includes<br />
BS, VDE and other international<br />
specifications.<br />
Installation<br />
After cable preparation, the lubricated<br />
stress control adapter is simply slid into<br />
place. The high performance multi range<br />
mechanical lugs are quickly installed by<br />
shearing off the bolts. When lubricated,<br />
the screened connector body can easily<br />
be slid onto the cable end and fixed to the<br />
bushing by a threaded pin and nut. The<br />
open end is sealed by a backplug or by a<br />
connection plug, which allows parallel<br />
connection of two cables.<br />
4 2<br />
1<br />
2<br />
3<br />
4<br />
Double connections<br />
For double connections of RSTI-56 series<br />
a T-connector and a coupling connector<br />
(2 T-connectors and a connection plug)<br />
have to be ordered. Installation<br />
dimensions D/d/H of 290 (365)/125 (175)/<br />
285 mm are required.<br />
For double connections of RSTI-76 series<br />
a T-connector and a coupling connector<br />
have to be ordered. Installation dimensions<br />
D/d/H of 325/125/300 mm are<br />
required.<br />
5<br />
Cut-away drawing of<br />
RSTI-56 series T-connector<br />
1Mechanical lug<br />
2 Screened body<br />
3 Stress cone adapter<br />
4 Earthing eye and ground lead<br />
5 Threaded pin<br />
6 Back plug with test point<br />
7 Test point<br />
8 Conductive endcap<br />
D<br />
d<br />
Configuration of RSTI-56 as double<br />
T-connection<br />
6<br />
7<br />
8<br />
H