Introduction to Microcontrollers Lab Manual - Microchip

More documents

Recommendations

Info

LABS NOTES: DS51963A-page 42 2011 Microchip Technology Inc.
6.1 OBJECTIVE 6.2 PRE-LAB Lab 6. Analog-to-Digital Converter LABS Configure the PIC24FJ256GB110 10-bit A/D converter module to create a simple voltage meter. 6.2.1 Reference Material • PIC24FJ256GB110 Family Data Sheet (DS39897) • 16-Bit MCU and DSC Programmer's Reference Manual (DS70157) • MPLAB IDE User's Guide (DS51519) • PIC24F Family Reference Manual – Section 8. Interrupts (DS39707) • PIC24F Family Reference Manual – Section 17. 10-Bit A/D Converter (DS39705) 6.2.2 A/D Converter The PIC24FJ256GB110 incorporates a 10-bit successive approximation converter. Figure 6-1 illustrates the internal structure of the A/D Converter module. 2011 Microchip Technology Inc. DS51963A-page 43
Page 1 and 2: Introduction to Microcontrollers La
Page 3 and 4: INTRODUCTION TO MICROCONTROLLERS LA
Page 5 and 6: INTRODUCTION INTRODUCTION TO MICROC
Page 7 and 8: 0.1 OBJECTIVE 0.2 PRE-LAB Lab 0. In
Page 9 and 10: 0.3 THE LAB 0.2.5 I/O Ports The abi
Page 11 and 12: 0.3.5 Programming the Device In ord
Page 13 and 14: 1.1 OBJECTIVE 1.2 PRE-LAB Lab 1. Ti
Page 15 and 16: Setup the Simulator processor frequ
Page 17 and 18: FIGURE 1-3: LAB 1 BASIC PROGRAM FLO
Page 19 and 20: 2.1 INTERRUPTS 2.2 PRE-LAB 2.1.1 Ob
Page 21 and 22: FIGURE 2-2: LAB 2 PRIMARY AND ALTER
Page 23 and 24: 2.2.3 IDE Concepts Watch Window It
Page 25 and 26: 3.1 OBJECTIVE 3.2 PRE-LAB Lab 3. UA
Page 27 and 28: 3.2.4 I/O Ports with Peripheral Pin
Page 29 and 30: For example: Mapping Action Map “
Page 31 and 32: 3.3 THE LAB 3.3.1 Objective Program
Page 33 and 34: 4.1 OBJECTIVE 4.2 PRE-LAB Lab 4. Wa
Page 35 and 36: 4.3 THE LAB 4.2.4 Configuration Bit
Page 37 and 38: 5.1 OBJECTIVE 5.2 PRE-LAB Lab 5. Co
Page 39 and 40: FIGURE 5-4: LAB 5 COMPARATOR VOLTAG
Page 41: FIGURE 5-5: LAB 5 BASIC PROGRAM FLO
Page 45 and 46: To configure the A/D module, the fo
Page 47 and 48: 6.3 THE LAB The first code transiti
Page 49 and 50: FIGURE 6-5: LAB 6 PROGRAM FLOW The
Page 51 and 52: 7.1 OBJECTIVE 7.2 PRE-LAB Lab 7. Pu
Page 53 and 54: FIGURE 7-3: OUTPUT COMPARE BLOCK DI
Page 55 and 56: LEDs are on the following ports: LE
Page 57 and 58: 8.1 OBJECTIVE 8.2 PRE-LAB Lab 8. Ex
Page 59 and 60: 8.2.7 Serial Peripheral Interface (
Page 61 and 62: 8.3 THE LAB 8.3.1 Objective Write a
Page 63 and 64: 9.1 OBJECTIVE 9.2 PRE-LAB Lab 9. Po
Page 65 and 66: FIGURE 9-1: PIC24FJ256GB110 FAMILY
Page 67 and 68: 9.3 THE LAB 9.2.7 Microchip XLP Tec
Page 69 and 70: 10.1 OBJECTIVE 10.2 THE LAB Lab 10.
Page 71 and 72: INTRODUCTION TO MICROCONTROLLERS LA
Page 73 and 74: A.3 STEP THREE: CREATE NEW PROJECT

Introduction to Microcontrollers Lab Manual - Microchip

Create successful ePaper yourself

Delete template?

Save as template?