Unified Access Point (AP) Administrator's Guide

More documents

Recommendations

Info

D-Link Unified Access Point Administrator’s Guide Table 7. Ethernet Settings Field Description MAC Address Shows the MAC address for the LAN interface for the Ethernet port on this access point. This is a read-only field that you cannot change. Management VLAN ID The management VLAN is the VLAN associated with the IP address you use to access the AP. The default management VLAN ID is 1. Provide a number between 1 and 4094 for the management VLAN ID. Untagged VLAN If you disable untagged VLANs, all traffic is tagged with a VLAN ID. By default all traffic on the Unified Access Point uses VLAN 1, which is the default untagged VLAN. This means that all traffic is untagged until you disable untagged VLANs, change the untagged traffic VLAN ID, or change the VLAN ID for a virtual access point (VAP) or a client using RADIUS. Untagged VLAN ID Provide a number between 1 and 4094 for the untagged VLAN ID. Traffic on the VLAN that you specify in this field will not be tagged with a VLAN ID. Connection Type If you select DHCP, the access point acquires its IP address, subnet mask, DNS, and gateway information from a DHCP server. If you select Static IP, you must enter information in the Static IP Address, Subnet Mask, and Default Gateway fields. Static IP Address Enter the static IP address in the text boxes. This field is disabled if you use DHCP as the connection type. Subnet Mask Enter the subnet mask in the text boxes. Default Gateway Enter the default gateway in the text boxes. DNS Nameservers Select the mode for the DNS. In Dynamic mode, the IP addresses for the DNS servers are assigned automatically via DHCP. (This option is only available if you specified DHCP for the Connection Type.) In Manual mode, you must assign static IP addresses to resolve domain names. NOTE: After you configure the Ethernet settings, you must click Update to apply the changes and to save the settings. Changing some access point settings might cause the AP to stop and restart system processes. If this happens, wireless clients will temporarily lose connectivity. We recommend that you change access point settings when WLAN traffic is low. 32 © 2001-2008 D-Link Corporation. All Rights Reserved.
Using the CLI to Configure Ethernet Settings 3 Installing the Access Point Use the commands in Table 8 to view and set values for the Ethernet (wired) interface. For more information about each setting, see the description for the field in Table 7. Table 8. CLI Commands for Ethernet Settings Action Command Get the DNS Name get host id Set the DNS Name set host id Get Current Settings for the Ethernet (Wired) Internal Interface For example: set host id vicky-ap get management Set the management VLAN ID set management vlan-id View untagged VLAN information get untagged-vlan Enable the untagged VLAN set untagged-vlan status up Disable the untagged VLAN set untagged-vlan status down Set the untagged VLAN ID set untagged-vlan vlan-id View the connection type get management dhcp-status Use DHCP as the connection type set management dhcp-client status up Use a Static IP as the connection set management dhcp-client status down type Set the Static IP address set management static-ip Example: set management static-ip 10.10.12.221 Set a Subnet Mask set management static-mask Example: Set the Default Gateway View the DNS Nameserver mode Dynamic= up Manual=down set management static-mask 255.0.0.0 set static-ip-route gateway Example: set static-ip-route gateway 10.254.0.1 Note that there is no need to set static-ip-route mask or staticip-route destination when setting the default gateway. In general, the static-ip-route mask should be set as the netmask for the destination net: “255.255.255.255” for a host or left as “0.0.0.0” for the default route. get host dns-via-dhcp Configuring the Ethernet Interface 33
Page 1 and 2: Unified Access Point (AP) Administr
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Table of Contents Viewing Neighbori
Page 7 and 8: List of Figures List of Figures Fig
Page 9 and 10: List of Tables List of Tables Table
Page 11 and 12: About This Document About This Docu
Page 13 and 14: About This Document Figure 1 shows
Page 15 and 16: Overview of the D-Link Access Point
Page 17 and 18: SpectraLink Voice Priority (SVP) 1
Page 19 and 20: Preparing to Install the Access Poi
Page 21 and 22: Table 2. AP Default Settings Featur
Page 23 and 24: 2 Preparing to Install the Access P
Page 25 and 26: Installing the Access Point 3 This
Page 27 and 28: 3 Installing the Access Point 2. Co
Page 29 and 30: 3 Installing the Access Point 7. If
Page 31: Configuring the Ethernet Interface
Page 35 and 36: 3 Installing the Access Point Using
Page 37 and 38: 3 Installing the Access Point Once
Page 39 and 40: Configuring Access Point Security T
Page 41 and 42: 4 Configuring Access Point Security
Page 45 and 46: None Static WEP IEEE 802.1X WPA Per
Page 47 and 48: Table 11. Static WEP 4 Configuring
Page 53 and 54: Table 14. WPA Enterprise 4 Configur
Page 55 and 56: Managing the Access Point 5 This ch
Page 57 and 58: Using the 802.11h Wireless Mode The
Page 59 and 60: 5 Managing the Access Point Table 1
Page 61 and 62: Table 16. Radio Settings 5 Managing
Page 63 and 64: To set up multiple virtual access p
Page 65 and 66: Table 17. VAP Configuration 5 Manag
Page 67 and 68: 5 Managing the Access Point Table 1
Page 69 and 70: Configuring Access Point Services 6
Page 71 and 72: 6 Configuring Access Point Services
Page 73 and 74: Packet Bursting for Better Performa
Page 75 and 76: Configuring QoS Settings 6 Configur
Page 77 and 78: Table 22. QoS Settings Field Descri
Page 79 and 80: Table 22. QoS Settings Field Descri
Page 81 and 82: Maintaining the Access Point 7 This
Page 83 and 84:
Saving the Current Configuration to
Page 85 and 86:
Rebooting the Access Point 7 Mainta
Page 87 and 88:
Configuring the Access Point for Ma
Page 89 and 90:
Table 24. Managed Access Point 8 Co
Page 91 and 92:
Viewing Access Point Status 9 This
Page 93 and 94:
9 Viewing Access Point Status your
Page 95 and 96:
9 Viewing Access Point Status Enabl
Page 97 and 98:
Table 27. Transmit/Receive Statisti
Page 99 and 100:
Table 29 describes the information
Page 101 and 102:
Wireless Client Settings and RADIUS
Page 103 and 104:
A Wireless Client Settings and RADI
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Choose Open To use this type of sec
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
3 A Wireless Client Settings and RA
Page 117 and 118:
Page 119 and 120:
5. Click Finish. A Wireless Client
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
CLI for AP Configuration B In addit
Page 127 and 128:
1. Start your SSH application. (We
Page 129 and 130:
The rest of the command line contai
Page 131 and 132:
B CLI for AP Configuration Example
Page 133 and 134:
Table 33. Interface Naming Conventi
Page 135 and 136:
Status Table 34. Basic Setting Comm
Page 137 and 138:
Table 36. Ethernet Setting Commands
Page 139 and 140:
Table 38. Radio Setting Commands Ac
Page 141 and 142:
Index to 4. DLINK-AP# set interface
Page 143 and 144:
B CLI for AP Configuration and so o
Page 145 and 146:
1. Set the Security Mode DLINK-AP#
Page 147 and 148:
Table 40. Managed Access Point Comm
Page 149 and 150:
Time B CLI for AP Configuration The
Page 151 and 152:
Table 46. CLI Class Instances has n
Page 153 and 154:
Glossary 0-9 A B C D E F G H I J K
Page 155 and 156:
over layer 2 switched networks. It
Page 157 and 158:
detection whereas with CSMA/CA the
Page 159 and 160:
H HTTP The Hypertext Transfer Proto
Page 161 and 162:
Lease Time The Lease Time specifies
Page 163 and 164:
inspected by each node. The node to
Page 165 and 166:
wireless local area network. It is
Page 167 and 168:
W WAN A Wide Area Network (WAN) is
show all

Unified Access Point (AP) Administrator's Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?