Download - heidenhain - DR. JOHANNES HEIDENHAIN GmbH

More documents

Recommendations

Info

Qty. Description ID 1 Adapter cable (extension) 17/17-pin (Mot.Enc.) see chapter 4.7.1 340302-xx 1 Adapter cable 17/15-pin; 3 m see chapter 4.7.1 332115-03 1 Adapter cable 17/25-pin; 0.3 m (assignment converter) see chapter 4.7.1 509667-N3 1 Adapter cable 17/25-pin; 0.3 m (assignment converter) see chapter 4.7.1 509666-N3 1 Adapter cable 17/15-pin; 0.3 m see chapter 4.7.1 510616-N3 1 Voltage controller 5 V Pos.Enc. see chapter 4.7.1 370225-01 1 Voltage controller 5 V Mot.Enc. see chapter 4.7.1 370224-01 1 Adapter cable (extension) 17-pin (Pos.Enc. assignment) see chapter 4.7.1 323897-xx DRIVE-CLiQ * 1 Connecting cable SIEMENS DRIVE-CLiQ line MOTION-CONNECT 759314-01 * DRIVE-CLiQ is a registered trademark of the SIEMENS Aktiengesellschaft March 2011 General 13
14 HEIDENHAIN ATS Software Operating Instructions
Page 1 and 2: Operating Instructions ATS Software
Page 3 and 4: 4.3.1 Cable adapter for EnDat 2.2.
Page 5 and 6: 1.2 Safety Precautions Note Observe
Page 7 and 8: 1.4 IK 215 Adjusting and Testing Pa
Page 9 and 10: 1.7 PWM 20 Encoder Diagnostic Kit ,
Page 11: Qty. Description ID ExI 11xx/13xx a
Page 15 and 16: 2.3 Installing the ATS Software 2.4
Page 17 and 18: 18 HEIDENHAIN ATS Software Operatin
Page 19 and 20: 3.2 Connect Encoder Connect the en
Page 21 and 22: 3.2.1 Automatic encoder identificat
Page 23 and 24: If the ATS software has found a dif
Page 25 and 26: In the Encoder selection box, click
Page 27 and 28: Typical error message of purely ser
Page 29 and 30: 3.3 Basic Functions Note Display an
Page 31 and 32: Status display Each time position d
Page 33 and 34: Detailed display of encoder status
Page 35 and 36: Open the directory tree "Parameters
Page 37 and 38: Detailed display of encoder status
Page 39 and 40: Connection to EIB interface electro
Page 41 and 42: Note The warning in the Encoder sta
Page 43 and 44: Clear incremental counter Equate fu
Page 45 and 46: The bit length may vary and depends
Page 47 and 48: 2. Non EnDat-compliant datum shift
Page 49 and 50: Press the "function-specific view"
Page 51 and 52: 2. Editing in the datum shift windo
Page 53 and 54: The green annulus represents the to
Page 55 and 56: 3.3.3 Display encoder memory Callin
Page 57 and 58: Load encoder configuration from enc
Page 59 and 60: Apply encoder configuration Functio
Page 61 and 62: Binary value display Hexadecimal va
Page 63 and 64:
Setting write protection for memory
Page 65 and 66:
The log window ("Protocol") appears
Page 67 and 68:
3.3.5 Voltage display Voltage: Disp
Page 69 and 70:
Temperature sensor 1: External sens
Page 71 and 72:
Double-click "Absolute/incremental
Page 73 and 74:
If the deviation span is extremely
Page 75 and 76:
At the beginning of the Diagnostic
Page 77 and 78:
3.5.3.1 Open Loop function Click O
Page 79 and 80:
When you click the "Encoder paramet
Page 81 and 82:
3.5.4.2 Closed Loop function Click
Page 83 and 84:
3.6.1 Configure hardware 1 PCI bus
Page 85 and 86:
3.6.3 Manage product keys In additi
Page 87 and 88:
3.6.4 Display software version To d
Page 89 and 90:
3.7.1 Exl Check Function Step 1: Co
Page 91 and 92:
Step 2: Checking the scanning gap
Page 93 and 94:
Explanation on mounting quality: Th
Page 95 and 96:
3.7.2 ExI mounting function Step 1:
Page 97 and 98:
Step 2: Adjusting the scanning gap
Page 99 and 100:
The tolerance range must be reached
Page 101 and 102:
The encoder is aligned manually by
Page 103 and 104:
3.9 Supported Interfaces 3.9.1 SSI,
Page 105 and 106:
3.9.2 FANUC and MITSUBISHI The soft
Page 107 and 108:
The information transferred via DRI
Page 109 and 110:
Display of encoder parameters The m
Page 111 and 112:
p10101: This parameter defines the
Page 113 and 114:
4.2 EnDat 2.1 / 2.2 with Incrementa
Page 115 and 116:
4.2.3 Connecting the PWM 20/IK 215
Page 117 and 118:
4.2.5 Connecting the PWM 20/IK 215
Page 119 and 120:
4.3.2 Cable adapter for APE 3xx and
Page 121 and 122:
4.5 FANUC 4.5.1 Measuring the FANUC
Page 123 and 124:
4.7 SSI 4.7.1 Connecting the PWM 20
Page 125 and 126:
5.3 Pin Layout of PCB Connector of
Page 127 and 128:
5.5 FANUC Pin Layout 128 HEIDENHAIN
Page 129 and 130:
130 HEIDENHAIN ATS Software Operati
Page 131:
132 HEIDENHAIN ATS Software Operati
show all

Download - heidenhain - DR. JOHANNES HEIDENHAIN GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?