Download - heidenhain - DR. JOHANNES HEIDENHAIN GmbH

More documents

Recommendations

Info

2 Commissioning 2.1 System Requirements Dual-core processor with a clock frequency > 2 GHz At least 1 GB RAM Windows XP, Vista, Win7 (32 bits) operating system Free space on hard disk > 100 MB Note 2.2 Description of the Hardware If these requirements are not met, this may lead to very slow data processing or even to error messages of the ATS software, indicating that certain functions cannot be performed. System requirements for PWM 20 or IK 215: see respective commissioning instructions To be operable, the ATS software requires a hardware platform for connection of the encoders. The ATS software is executable on HEIDENHAIN PWM 20 or IK 215. With the introduction of the ATS version 2.4 the PWM 20 entirely supersedes the IK 215. PWM 20 + ATS V2.4 feature all functions of IK 215. The improvement of the ATS software functions is focused on the PWM 20. Certain functions - such as connecting devices with DRIVE-CLiQ interface or working with the LIP 200 mounting wizard - are only possible with the PWM 20. For more information on specifications, supported interfaces, hardware installation, etc., please refer to the respective commissioning instructions. March 2011 Commissioning 15
2.3 Installing the ATS Software 2.4 Uninstalling the ATS Software A CD-ROM with the required software is among the items supplied. The current ATS software is also available for downloading at www.heidenhain.de. The software is updated regularly. To install the ATS software, insert the supplied CD into your CD-ROM drive or run the "setup.exe" file downloaded from the Internet. Follow the installation program instructions. If the setup wizard does not start automatically, please start "setup.exe" manually. Before you start the installation, please read the Release Notes. After successful completion of the installation, the icon of the ATS software is displayed on the desktop. The software can be uninstalled in different ways: Start the ATS Uninstall Routine via the corresponding Windows button. Via the "Control Panel" --> "Software" operating system function. Restart the "setup.exe" of the ATS Software; follow the installation wizard and select the "Remove" option. 16 HEIDENHAIN ATS Software Operating Instructions
Page 1 and 2: Operating Instructions ATS Software
Page 3 and 4: 4.3.1 Cable adapter for EnDat 2.2.
Page 5 and 6: 1.2 Safety Precautions Note Observe
Page 7 and 8: 1.4 IK 215 Adjusting and Testing Pa
Page 9 and 10: 1.7 PWM 20 Encoder Diagnostic Kit ,
Page 11 and 12: Qty. Description ID ExI 11xx/13xx a
Page 13: 14 HEIDENHAIN ATS Software Operatin
Page 17 and 18: 18 HEIDENHAIN ATS Software Operatin
Page 19 and 20: 3.2 Connect Encoder Connect the en
Page 21 and 22: 3.2.1 Automatic encoder identificat
Page 23 and 24: If the ATS software has found a dif
Page 25 and 26: In the Encoder selection box, click
Page 27 and 28: Typical error message of purely ser
Page 29 and 30: 3.3 Basic Functions Note Display an
Page 31 and 32: Status display Each time position d
Page 33 and 34: Detailed display of encoder status
Page 35 and 36: Open the directory tree "Parameters
Page 37 and 38: Detailed display of encoder status
Page 39 and 40: Connection to EIB interface electro
Page 41 and 42: Note The warning in the Encoder sta
Page 43 and 44: Clear incremental counter Equate fu
Page 45 and 46: The bit length may vary and depends
Page 47 and 48: 2. Non EnDat-compliant datum shift
Page 49 and 50: Press the "function-specific view"
Page 51 and 52: 2. Editing in the datum shift windo
Page 53 and 54: The green annulus represents the to
Page 55 and 56: 3.3.3 Display encoder memory Callin
Page 57 and 58: Load encoder configuration from enc
Page 59 and 60: Apply encoder configuration Functio
Page 61 and 62: Binary value display Hexadecimal va
Page 63 and 64: Setting write protection for memory
Page 65 and 66:
The log window ("Protocol") appears
Page 67 and 68:
3.3.5 Voltage display Voltage: Disp
Page 69 and 70:
Temperature sensor 1: External sens
Page 71 and 72:
Double-click "Absolute/incremental
Page 73 and 74:
If the deviation span is extremely
Page 75 and 76:
At the beginning of the Diagnostic
Page 77 and 78:
3.5.3.1 Open Loop function Click O
Page 79 and 80:
When you click the "Encoder paramet
Page 81 and 82:
3.5.4.2 Closed Loop function Click
Page 83 and 84:
3.6.1 Configure hardware 1 PCI bus
Page 85 and 86:
3.6.3 Manage product keys In additi
Page 87 and 88:
3.6.4 Display software version To d
Page 89 and 90:
3.7.1 Exl Check Function Step 1: Co
Page 91 and 92:
Step 2: Checking the scanning gap
Page 93 and 94:
Explanation on mounting quality: Th
Page 95 and 96:
3.7.2 ExI mounting function Step 1:
Page 97 and 98:
Step 2: Adjusting the scanning gap
Page 99 and 100:
The tolerance range must be reached
Page 101 and 102:
The encoder is aligned manually by
Page 103 and 104:
3.9 Supported Interfaces 3.9.1 SSI,
Page 105 and 106:
3.9.2 FANUC and MITSUBISHI The soft
Page 107 and 108:
The information transferred via DRI
Page 109 and 110:
Display of encoder parameters The m
Page 111 and 112:
p10101: This parameter defines the
Page 113 and 114:
4.2 EnDat 2.1 / 2.2 with Incrementa
Page 115 and 116:
4.2.3 Connecting the PWM 20/IK 215
Page 117 and 118:
4.2.5 Connecting the PWM 20/IK 215
Page 119 and 120:
4.3.2 Cable adapter for APE 3xx and
Page 121 and 122:
4.5 FANUC 4.5.1 Measuring the FANUC
Page 123 and 124:
4.7 SSI 4.7.1 Connecting the PWM 20
Page 125 and 126:
5.3 Pin Layout of PCB Connector of
Page 127 and 128:
5.5 FANUC Pin Layout 128 HEIDENHAIN
Page 129 and 130:
130 HEIDENHAIN ATS Software Operati
Page 131:
132 HEIDENHAIN ATS Software Operati
show all

Download - heidenhain - DR. JOHANNES HEIDENHAIN GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?