snap ethernet-based i/o units protocols and programming guide

More documents

Recommendations

Info

APPENDIX A: SNAP ETHERNET-BASED BRAIN MEMORY MAP Starting Address Length Type Description FFFF F03A 8210 4 UI Port B, position 0: End-of-message characters. (Additional ports follow in order on even 10 hex boundaries.) FFFF F03A 8400 1 UI Position 0: Module mode of operation (0 = 2-wire; 1 = 4-wire) FFFF F03A 8401 1 UI Position 1: Module mode of operation (0 = 2-wire; 1 = 4-wire) Last valid address for this area: FFFF F03A 840F (Additional modules follow in order.) Serial Module and Port Numbers For quick reference, the following table shows serial modules and ports, their default IP port numbers, and their starting memory map addresses, beginning with FFFF F03A 8000. Module Port Default IP Port Memory Map Address Module Port Default IP Port 112 SNAP Ethernet-Based I/O Units Protocols and Programming Guide Memory Map Address 0 A 22500 8000 8 A 22516 8100 0 B 22501 8010 8 B 22517 8110 1 A 22502 8020 9 A 22518 8120 1 B 22503 8030 9 B 22519 8130 2 A 22504 8040 10 A 22520 8140 2 B 22505 8050 10 B 22521 8150 3 A 22506 8060 11 A 22522 8160 3 B 22507 8070 11 B 22523 8170 4 A 22508 8080 12 A 22524 8180 4 B 22509 8090 12 B 22525 8190 5 A 22510 80A0 13 A 22526 81A0 5 B 22511 80B0 13 B 22527 81B0 6 A 22512 80C0 14 A 22528 81C0 6 B 22513 80D0 14 B 22529 81D0 7 A 22514 80E0 15 A 22530 81E0 7 B 22515 80F0 15 B 22531 81F0
Wiegand Serial Module Configuration—Read/Write (Does not apply to SNAP Simple I/O) Use this area to configure SNAP Wiegand serial communication modules on the rack. Only a few modules and ports are shown in the table. Other ports and modules on the rack follow the same pattern. See the table on page 114 for a list of module and port numbers. For important information on using these modules, see Opto 22 form 1191, SNAP Serial Communication Module User’s Guide. Starting Address Length Type Description FFFF F03A 8500 4 UI Wiegand module 0: Loader version number FFFF F03A 8504 4 UI Wiegand module 0: Firmware (kernel) version number FFFF F03A 8508 4 UI Wiegand module 1: Loader version number FFFF F03A 850C 4 UI Wiegand module 1: Firmware (kernel) version number (Modules 2–15 follow in order.) FFFF F03A 8600 4 UI Port A on Wiegand module in position 0 on the rack: IP port number for access to serial port. Default is 22500. FFFF F03A 8604 4 UI Port A, position 0: Data format (O for Opto format, 26, 30, 32, 34, 35, 36, 37, 40, or C for custom format) FFFF F03A 8608 4 UI Port A, position 0: Total length of data in the transmission FFFF F03A 860C 4 UI Port A, position 0: First bit of the site code FFFF F03A 8610 4 UI Port A, position 0: Length of the site code, in bits FFFF F03A 8614 4 UI Port A, position 0: First bit of the badge code (should be the next bit after the site code) FFFF F03A 8618 4 UI Port A, position 0: Length of the badge code, in bits FFFF F03A 861C 24 -- Pad for alignment FFFF F03A 8640 4 UI Port B on Wiegand module in position 0 on the rack: IP port number for access to serial port. Default is 22501. FFFF F03A 8644 4 UI Port B, position 0: Data format (O for Opto format, 26, 30, 32, 34, 35, 36, 37, 40, or C for custom format) FFFF F03A 8648 4 UI Port B, position 0: Total length of data in the transmission FFFF F03A 864C 4 UI Port B, position 0: First bit of the site code FFFF F03A 8650 4 UI Port B, position 0: Length of the site code, in bits FFFF F03A 8654 4 UI Port B, position 0: First bit of the badge code (should be the next bit after the site code) FFFF F03A 8658 4 UI Port B, position 0: Length of the badge code, in bits SNAP Ethernet-Based I/O Units Protocols and Programming Guide 113
Page 1 and 2:
SNAP ETHERNET-BASED I/O UNITS PROTO
Page 3 and 4:
Table of Contents Chapter 1: Introd
Page 5 and 6:
Non-velocity Algorithms............
Page 7 and 8:
Disconnecting......................
Page 9 and 10:
Data Logging Configuration—Read/W
Page 11 and 12:
Chapter 1 Introduction CHAPTER 1 We
Page 13 and 14:
About this Guide CHAPTER 1: INTRODU
Page 15 and 16:
For Help CHAPTER 1: INTRODUCTION If
Page 17 and 18:
FEATURE CHAPTER 1: INTRODUCTION Ema
Page 19 and 20:
CHAPTER 1: INTRODUCTION This task C
Page 21 and 22:
CHAPTER 2 Chapter 2 Overview of Pro
Page 23 and 24:
Referencing SNAP I/O Points CHAPTER
Page 25 and 26:
Analog and Digital Systems (N Brain
Page 27 and 28:
Digital-Only Systems The following
Page 29 and 30:
I/O Point Types CHAPTER 2: OVERVIEW
Page 31 and 32:
CHAPTER 2: OVERVIEW OF PROGRAMMING
Page 33 and 34:
Watchdog (Digital and Analog Points
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Streaming Data CHAPTER 2: OVERVIEW
Page 47 and 48:
Logging Data Area Number of Bytes I
Page 49 and 50:
Using PID Loops What is a PID? CHAP
Page 51 and 52:
Equations Common to All Algorithms
Page 53 and 54:
Page 55 and 56:
CHAPTER 3 Chapter 3 Using the SNAP
Page 57 and 58:
CHAPTER 3: USING THE SNAP ETHERNET
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Environment Visual Basic 6 Internet
Page 65 and 66:
MemMap Example Code CHAPTER 3: USIN
Page 67 and 68:
Page 69 and 70:
Page 71 and 72: Return Values CHAPTER 3: USING THE
Page 73 and 74: IsOpenDone V Close V Return Values
Page 75 and 76: Digital Point Methods CHAPTER 3: US
Page 77 and 78: SetDigBankOnMask V [in] long nPts63
Page 79 and 80: Analog Bank Methods CHAPTER 3: USIN
Page 81 and 82: GetStatusWatchdogTime [out] long pn
Page 83 and 84: CHAPTER 3: USING THE SNAP ETHERNET
Page 85 and 86: CHAPTER 3: USING THE SNAP ETHERNET
Page 87 and 88: GetLastStreamStandardBlock (ActiveX
Page 89 and 90: CHAPTER 4 Chapter 4 Using the IEEE
Page 91 and 92: CHAPTER 4: USING THE IEEE 1394-BASE
Page 93 and 94: Bytes 0-3 Bytes 4-7 Bytes 8-11 Byte
Page 95 and 96: Bytes 0-3 Bytes 4-7 Bytes 8-11 The
Page 97 and 98: Bytes 0-3 Bytes 4-7 Bytes 8-11 Byte
Page 99 and 100: Read and clear latches for individu
Page 101 and 102: Scaling CHAPTER 4: USING THE IEEE 1
Page 103 and 104: Read and Write Packet Structure Par
Page 109 and 110: CHAPTER 5 Chapter 5 Advanced Modbus
Page 111 and 112: CHAPTER 5: ADVANCED MODBUS PROGRAMM
Page 113 and 114: APPENDIX A Appendix A SNAP Ethernet
Page 115 and 116: Status Area Read—Read Only This i
Page 117 and 118: Date and Time Configuration—Read/
Page 119 and 120: Security Configuration—Read/Write
Page 121: Serial Module Configuration—Read/
Page 125 and 126: SNMP Configuration—Read/Write (Do
Page 127 and 128: Starting Address Length Type Descri
Page 131 and 132: Digital Point Read—Read Only NOTE
Page 133 and 134: Analog Point Read—Read Only See
Page 135 and 136: Analog and Digital Point Configurat
Page 137 and 138: Digital Events and Reactions—Read
Page 141 and 142: Analog Point Calculation and Set—
Page 143 and 144: Analog Read and Clear/Restart—Rea
Page 149 and 150: Serial Event Configuration—Read/W
Page 157 and 158: Data Log—Read/Write (Does not app
Page 159 and 160: Appendix B Table of Offsets Introdu
Page 161 and 162: Module Point (Decimal) Point (Hex)
Page 163 and 164: Index A access, setting up SNMP sec
Page 165 and 166: error codes IEEE 1394-based protoco
Page 167 and 168: O off-latch, 20 offset, 24 IEEE 139
show all

snap ethernet-based i/o units protocols and programming guide

Create successful ePaper yourself

Delete template?

Save as template?