snap ethernet-based i/o units protocols and programming guide
snap ethernet-based i/o units protocols and programming guide
snap ethernet-based i/o units protocols and programming guide
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
I/O Point Types<br />
CHAPTER 2: OVERVIEW OF PROGRAMMING<br />
The following table lists values for I/O point types. Default types are shaded. If a point differs<br />
from the default, use the values in the table to configure the point.<br />
Point Type SNAP Module<br />
Part Number<br />
Digital Points<br />
Value<br />
(Hex)<br />
Digital Input Any SNAP digital input 100<br />
Digital Output Any SNAP digital output 180<br />
Analog Input Points<br />
0 to 20 mA Input SNAP-AIMA, SNAP-AIMA-i,<br />
SNAP-AIMA-iSRC, SNAP-AIMA-4<br />
4 to 20 mA Input SNAP-AIMA, SNAP-AIMA-i,<br />
SNAP-AIMA-iSRC, SNAP-AIMA-4<br />
-20 mA to +20 mA Input SNAP-AIMA, SNAP-AIMA-i,<br />
SNAP-AIMA-iSRC, SNAP-AIMA-4<br />
0 to 10 Amps RMS Input SNAP-AIARMS, SNAP-AIPM (point 2 only) 47<br />
-25 mV to +25 mV Input SNAP-AITM2, SNAP-AITM2-i, SNAP-AIMV2-4 43<br />
-50 mV to +50 mV Input SNAP-AITM2, SNAP-AITM2-i, SNAP-AIMV2-4 09<br />
-75 mV to +75 mV Input SNAP-AITM, SNAP-AITM-i, SNAP-AIMV-4 44<br />
-150 mV to +150 mV Input SNAP-AITM, SNAP-AITM-i, SNAP-AIMV-4 42<br />
0 to 5 V Input SNAP-AIV, SNAP-AIV-i, SNAP-AIV-4 06<br />
0 to 10 V Input SNAP-AIV, SNAP-AIV-i, SNAP-AIV-4 07<br />
-5 V to +5 V Input SNAP-AIV, SNAP-AIV-i, SNAP-AIV-4 0B<br />
-10 V to +10 V Input SNAP-AIV, SNAP-AIV-i, SNAP-AIV-4 0C<br />
0 to 250 V RMS Input SNAP-AIVRMS, SNAP-AIPM (point 1 only) 46<br />
Temperature Input (ICTD) SNAP-AICTD, SNAP-AICTD-4 04<br />
Resistance (Thermistor) Input, 0–40 K ohms SNAP-AIR40K-4 4A<br />
Resistance (Thermistor) Input, 0–200 K ohms SNAP-AIR40K-4 4B<br />
Resistance (Thermistor) Input, 0–10 K ohms SNAP-AIR40K-4 4C<br />
Resistance (Thermistor) Input, 0–5 K ohms SNAP-AIR40K-4 4D<br />
100 Ohm Platinum 3-wire RTD (-200° to 850° C) SNAP-AIRTD 0A<br />
100 Ohm Nickel 3-wire RTD (-60° to 250° C) SNAP-AIRTD 2E<br />
120 Ohm Nickel 3-wire RTD (-80° to 260° C) SNAP-AIRTD 30<br />
Type E Thermocouple (-270° to 1,000° C) SNAP-AITM 13<br />
Type J Thermocouple (-210° to 1,200° C) SNAP-AITM 05<br />
SNAP Ethernet-Based I/O Units Protocols <strong>and</strong> Programming Guide 19<br />
02<br />
03<br />
40