snap ethernet-based i/o units protocols and programming guide

More documents

Recommendations

Info

APPENDIX A: SNAP ETHERNET-BASED BRAIN MEMORY MAP Starting Address Length Type Description FFFF F0C0 0044 4 UI Point 1: Point Type (unsigned integer). Use 0x0000 0100 for digital inputs. Use 0x0000 0180 for digital outputs. For analog types, see table on page 19. FFFF F0C0 0048 4 UI Point 1: Point Feature (unsigned integer) Digital feature values: 0x0000 0001 for counter input (configures and starts the counter) 0x0000 0004 for simple quadrature counter input 0x0000 0041 quadrature counter input with index. For quadrature counter information, see page 21. Analog feature values: none at present To disable point features, use 0x0000 0000 FFFF F0C0 004C 4 F Point 1: Point offsets (float) FFFF F0C0 0050 4 F Point 1: Point gains (float) FFFF F0C0 0054 4 F Point 1: Point high scaling factors (float) FFFF F0C0 0058 4 F Point 1: Point low scaling factors (float) FFFF F0C0 005C 4 -- Point 1: Reserved FFFF F0C0 0060 4 F Point 1: Average filter weight. (float) FFFF F0C0 0064 4 F Point 1: Watchdog value. EU float for analog and digital. 0 = off, non-0 = on. FFFF F0C0 0068 4 B Point 1: Enable watchdog (Boolean) 0 = disable; non-0 = enable FFFF F0C0 006C 4 -- Reserved FFFF F0C0 0070 10 S-ZT Point name (Additional points follow in order on even 40 hex boundaries.) FFFF F0C0 0FC0 4 UI Point 63: Read only. Module type reported by module. FFFF F0C0 1000 4 F Point 0: Analog output lower clamp (float) FFFF F0C0 1004 4 F Point 0: Analog output upper clamp (float) FFFF F0C0 1008 4 F Point 1: Analog output lower clamp (float) FFFF F0C0 100C 4 F Point 1: Analog output upper clamp (float) (Additional points follow in order) FFFF F0C0 11FC 4 F Point 63: Analog output lower clamp (float) Last valid address for this area: FFFF F0C0 11FF 126 SNAP Ethernet-Based I/O Units Protocols and Programming Guide
Digital Events and Reactions—Read/Write (Does not apply to SNAP Simple I/O) See page 30 for information on configuring digital events and reactions. Only the first two digital event/reactions are shown in the table. Other event/reactions follow the same pattern. Starting Address Length Type Description FFFF F0D0 0000 8 M Digital event 0: Points on? (mask) FFFF F0D0 0008 8 M Digital event 0: Points off? (mask) FFFF F0D0 0010 8 M Digital reaction 0: Turn points on (mask) FFFF F0D0 0018 8 M Digital reaction 0: Turn points off (mask) FFFF F0D0 0020 8 M Digital event 0: Scratch Pad bits on? (mask) FFFF F0D0 0028 8 M Digital event 0: Scratch Pad bits off? (mask) FFFF F0D0 0030 8 M Digital reaction 0: Turn Scratch Pad bits on (mask) FFFF F0D0 0038 8 M Digital reaction 0: Turn Scratch Pad bits off (mask) FFFF F0D0 0040 8 M Digital event 1: Points on? (mask) FFFF F0D0 0048 8 M Digital event 1: Points off? (mask) FFFF F0D0 0050 8 M Digital reaction 1: Turn points on (mask) FFFF F0D0 0058 8 M Digital reaction 1: Turn points off (mask) FFFF F0D0 0060 8 M Digital event 1: Scratch Pad bits on? (mask) FFFF F0D0 0068 8 M Digital event 1: Scratch Pad bits off? (mask) FFFF F0D0 0060 8 M Digital reaction 1: Turn Scratch Pad bits on (mask) FFFF F0D0 0068 8 M Digital reaction 1: Turn Scratch Pad bits off (mask) (Other digital event/reactions follow in order on even 40 hex boundaries.) Last valid address for this area: FFFF F0D0 FFFF SNAP Ethernet-Based I/O Units Protocols and Programming Guide 127
Page 1 and 2:
SNAP ETHERNET-BASED I/O UNITS PROTO
Page 3 and 4:
Table of Contents Chapter 1: Introd
Page 5 and 6:
Non-velocity Algorithms............
Page 7 and 8:
Disconnecting......................
Page 9 and 10:
Data Logging Configuration—Read/W
Page 11 and 12:
Chapter 1 Introduction CHAPTER 1 We
Page 13 and 14:
About this Guide CHAPTER 1: INTRODU
Page 15 and 16:
For Help CHAPTER 1: INTRODUCTION If
Page 17 and 18:
FEATURE CHAPTER 1: INTRODUCTION Ema
Page 19 and 20:
CHAPTER 1: INTRODUCTION This task C
Page 21 and 22:
CHAPTER 2 Chapter 2 Overview of Pro
Page 23 and 24:
Referencing SNAP I/O Points CHAPTER
Page 25 and 26:
Analog and Digital Systems (N Brain
Page 27 and 28:
Digital-Only Systems The following
Page 29 and 30:
I/O Point Types CHAPTER 2: OVERVIEW
Page 31 and 32:
CHAPTER 2: OVERVIEW OF PROGRAMMING
Page 33 and 34:
Watchdog (Digital and Analog Points
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Streaming Data CHAPTER 2: OVERVIEW
Page 47 and 48:
Logging Data Area Number of Bytes I
Page 49 and 50:
Using PID Loops What is a PID? CHAP
Page 51 and 52:
Equations Common to All Algorithms
Page 53 and 54:
Page 55 and 56:
CHAPTER 3 Chapter 3 Using the SNAP
Page 57 and 58:
CHAPTER 3: USING THE SNAP ETHERNET
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Environment Visual Basic 6 Internet
Page 65 and 66:
MemMap Example Code CHAPTER 3: USIN
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Return Values CHAPTER 3: USING THE
Page 73 and 74:
IsOpenDone V Close V Return Values
Page 75 and 76:
Digital Point Methods CHAPTER 3: US
Page 77 and 78:
SetDigBankOnMask V [in] long nPts63
Page 79 and 80:
Analog Bank Methods CHAPTER 3: USIN
Page 81 and 82:
GetStatusWatchdogTime [out] long pn
Page 83 and 84:
Page 85 and 86: CHAPTER 3: USING THE SNAP ETHERNET
Page 87 and 88: GetLastStreamStandardBlock (ActiveX
Page 89 and 90: CHAPTER 4 Chapter 4 Using the IEEE
Page 91 and 92: CHAPTER 4: USING THE IEEE 1394-BASE
Page 93 and 94: Bytes 0-3 Bytes 4-7 Bytes 8-11 Byte
Page 95 and 96: Bytes 0-3 Bytes 4-7 Bytes 8-11 The
Page 97 and 98: Bytes 0-3 Bytes 4-7 Bytes 8-11 Byte
Page 99 and 100: Read and clear latches for individu
Page 101 and 102: Scaling CHAPTER 4: USING THE IEEE 1
Page 103 and 104: Read and Write Packet Structure Par
Page 109 and 110: CHAPTER 5 Chapter 5 Advanced Modbus
Page 111 and 112: CHAPTER 5: ADVANCED MODBUS PROGRAMM
Page 113 and 114: APPENDIX A Appendix A SNAP Ethernet
Page 115 and 116: Status Area Read—Read Only This i
Page 117 and 118: Date and Time Configuration—Read/
Page 119 and 120: Security Configuration—Read/Write
Page 121 and 122: Serial Module Configuration—Read/
Page 123 and 124: Wiegand Serial Module Configuration
Page 125 and 126: SNMP Configuration—Read/Write (Do
Page 127 and 128: Starting Address Length Type Descri
Page 131 and 132: Digital Point Read—Read Only NOTE
Page 133 and 134: Analog Point Read—Read Only See
Page 135: Analog and Digital Point Configurat
Page 141 and 142: Analog Point Calculation and Set—
Page 143 and 144: Analog Read and Clear/Restart—Rea
Page 149 and 150: Serial Event Configuration—Read/W
Page 157 and 158: Data Log—Read/Write (Does not app
Page 159 and 160: Appendix B Table of Offsets Introdu
Page 161 and 162: Module Point (Decimal) Point (Hex)
Page 163 and 164: Index A access, setting up SNMP sec
Page 165 and 166: error codes IEEE 1394-based protoco
Page 167 and 168: O off-latch, 20 offset, 24 IEEE 139
show all

snap ethernet-based i/o units protocols and programming guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?