appendix 1 - Victor Technologies

More documents

Recommendations

Info

E. Air Line Regulator Bracket(s) Replacement NOTE There are two Air Line Regulator Brackets in this unit and both are replaced using this same procedure. 1. Remove the nut securing the Air Line Regulator to the mounting bracket. 2. Remove the four screws securing the Air Line Regulator Bracket to the Rear Panel. 3. Remove bracket from unit. 4. Install the replacement Air Line Regulator Bracket by reversing the above procedure. F. Air Line Regulator(s) Replacement NOTE This unit has two Air Line Regulators - one for plasma gas and one for secondary gas. This procedure applies to both Regulators. 1. Remove the Right Side Panel per Section 5.04-A. 2. Disconnect the gas input hose from the inert B fitting input located on the right side of the Air Line Regulator Assembly. Gas Pressure Regulator Filter Assemblies A-02327 Gas Input Input Hoses 3. Remove the four screws securing the Regulator to the Rear Panel. 4. Pull the Air Line Regulator away from the Rear Panel far enough to disconnect the plumbing joint between the Reducer and Elbow Fitting. 5. Remove the Regulator from the 2 inch brass nipple connected to the Solenoid Assembly. 6. Remove the elbow fitting from the old assembly. 7. Install the replacement Air Line Regulator Assembly by reversing the above procedure, keeping in mind the following: Apply pipe thread sealant to the fitting before reassembling. REPLACEMENT PROCEDURES 5-18 Manual 0-2697
6.01 Introduction SECTION 6: PARTS LISTS A. Parts List Breakdown The parts lists provide a breakdown of all replaceable components. Parts Lists are organized as follows: Section 6.03 Major External Replacement Parts Section 6.04 Access Panel Replacement Parts Section 6.05 Left Side Center Chassis Replacement Parts Section 6.06 Right Side Center Chassis Replacement Parts Section 6.07 Base Component Replacement Parts Section 6.08 Rear Panel Replacement Parts Section 6.09 Options and Accessories NOTE Parts listed without item numbers are not shown, but may be ordered by the catalog number shown. B. Returns If a product must be returned for service, contact your authorized distributor. Materials returned without proper authorization will not be accepted. C. Product Improvements Improvements to the product since release is denoted by a revision letter(s) located on the data tag of the unit. There are old style and new style data tags that may be encounted. The old style data tag has the revision letter(s) at the end of the serial number. The new style data tag has the revision letter(s) in an area marked 'Rev'. The parts lists may include references to the revision letter(s) for parts that are different between revisions. 6.02 Ordering Information Order replacement parts by catalog number and complete description of the part or assembly, as listed in the parts list for each type item. Also include the model and serial number of the torch. Address all inquiries to your authorized distributor. Manual 0-2697 6-1 PARTS LISTS
Page 1:
PLASMA CUTTING POWER SUPPLY PAK Mas
Page 4 and 5:
TABLE OF CONTENTS SECTION 1: GENERA
Page 7 and 8: SECTION 1: GENERAL INFORMATION 1.01
Page 9 and 10: 6. ANSI Standard Z49.2, FIRE PREVEN
Page 11 and 12: ultra-violets très forts. Ces rayo
Page 13 and 14: 1.07 Declaration of Conformity Manu
Page 15 and 16: SECTION 2: INTRODUCTION 2.01 Scope
Page 17 and 18: SECTION 3: DESCRIPTION 3.01 Scope o
Page 19 and 20: 15. Weight Power Supply with Torch:
Page 21 and 22: 4.01 Introduction SECTION 4: SERVIC
Page 23 and 24: The Logic PC Board controls the tim
Page 25 and 26: cut being more square than the othe
Page 27 and 28: Set the Power Supply RUN/SET switch
Page 29 and 30: 4. Clogged coolant filter and/or in
Page 31 and 32: a. Check continuity per appropriate
Page 33 and 34: NOTE Art may differ from actual uni
Page 35 and 36: H. Temperature Circuit Test The Pow
Page 37 and 38: ange, check between the two output
Page 39 and 40: SECTION 5: REPLACEMENT PROCEDURES 5
Page 41 and 42: C. Work Cable Replacement 1. Remove
Page 43 and 44: 5.06 Left Side Center Chassis Parts
Page 45 and 46: I. FET/Heatsink Assembly Replacemen
Page 47 and 48: G. Coolant Reservoir Replacement CA
Page 49 and 50: 9. Carefully slide the rear panel o
Page 51 and 52: M. Current Sense PC Board Assembly
Page 53 and 54: E. Motor (M5) / Fan / Pump Replacem
Page 55: 7. Remove rear panel from unit by c
Page 59 and 60: 6.04 Access Panel Replacement Parts
Page 61 and 62: 3 2 4 6 10 9 9 1 Manual 0-2697 6-5
Page 63 and 64: 12 1 5 4 3 17 10 11 21 10 Manual 0-
Page 65 and 66: 9 A-02278 3 11 10 20 6 5 23x4274 Ma
Page 67 and 68: 11 10 4 15 5 9 11 6 10 4 15 5 9 A-0
Page 69 and 70: APPENDIX 1: INPUT WIRING REQUIREMEN
Page 71 and 72: Pot/LED PC Board Signals APPENDIX 3
Page 73 and 74: J3-10 +12 vdc J3-11 Active Low Sign
Page 75 and 76: J9-1 36 VAC (b) from Logic PC Board
Page 77 and 78: J13-1 Active Low Start signal (Torc
Page 79 and 80: E1 E2 E7 E8 Component Side of PC Bo
Page 81 and 82: FET PC Board Signals (Upper and Low
Page 83 and 84: APPENDIX 11: CURRENT SENSOR PC BOAR
Page 85 and 86: APPENDIX 13: RECOMMENDED ROUTINE MA
Page 87 and 88: NOTE Transformer T3 in earlier prod
Page 89 and 90: NOTE Transformer T3 in earlier prod
Page 91: Art # A-04328
show all

appendix 1 - Victor Technologies

Create successful ePaper yourself

Delete template?

Save as template?