appendix 1 - Victor Technologies

More documents

Recommendations

Info

6.09 Options and Accessories Qty Description Catalog # 1 Two Stage Air Line Filter Kit Replacement Elements 7-7502 1 First Stage 9-1021 1 Second Stage 9-1022 1 Mounting Bracket CNC Interface Control Cable - Used With Shielded PCM Machine Torch 9-7535 1 25 ft (7.6 m) 8-5557 1 50 ft (15.2 m) 8-5558 1 575V Transformer Module Primary Input Power Cable, 10 ft. (3.05 m) 9-7700 1 230VAC, 2AWG, 4 COND, 600V 9-7697 1 460VAC, 6AWG, 4 COND, 600V 9-7696 1 "Y" Hose Assembly Kit 9-7827 1 Locking Caster Kit (2 Casters) 9-7868 1 Remote Pendant Control 20ft (6.1 m) - Used With Unshielded PCM Machine Torch 7-3460 PARTS LISTS 6-12 Manual 0-2697
APPENDIX 1: INPUT WIRING REQUIREMENTS Input Power Input Current Suggested Sizes (See Notes) Voltage Freq. 3-Ph 3-Ph Fuse (Amps) Wire (AWG) Wire (Canada) (Volts) (Hz) (kVA) (Amps) 3-Ph 3-Ph 3-Ph 208 50/60 28.1 78 100 2 2 220 50/60 28.6 75 100 2 2 230 50/60 29.5 74 100 2 2 240 50/60 29.9 72 90 2 2 380 50/60 29.0 44 60 6 6 415 50/60 29.5 41 60 6 6 460 50/60 29.5 37 50 6 6 575 Requires Transformer Module NOTES Refer to Local and National Codes or local authority having jurisdiction for proper wiring requirements. Cable size is de-rated based on the Duty Cycle of the equipment. The suggested sizes are based on flexible power cable with power plug installations. For hard-wired installations refer to local or national codes. Cable conductor temperature used is 167° F (75° C). Line Voltages with Suggested Circuit Protection and Wire Sizes Based on National Electric Code and Canadian Electrical Code An energy limiting fuse UL Class RK-1 (examples: BUSS LPS/LPN-RK or Gould-Shawmut AZK-A6K) should be used to minimize damage to Plasma Cutting, Welding or power distribution equipment. NEVER use replaceable element fuses like UL Class H, or "one-time" fuses like UL Class K5. Manual 0-2697 A-1 APPENDIX
Page 1:
PLASMA CUTTING POWER SUPPLY PAK Mas
Page 4 and 5:
TABLE OF CONTENTS SECTION 1: GENERA
Page 7 and 8:
SECTION 1: GENERAL INFORMATION 1.01
Page 9 and 10:
6. ANSI Standard Z49.2, FIRE PREVEN
Page 11 and 12:
ultra-violets très forts. Ces rayo
Page 13 and 14:
1.07 Declaration of Conformity Manu
Page 15 and 16:
SECTION 2: INTRODUCTION 2.01 Scope
Page 17 and 18: SECTION 3: DESCRIPTION 3.01 Scope o
Page 19 and 20: 15. Weight Power Supply with Torch:
Page 21 and 22: 4.01 Introduction SECTION 4: SERVIC
Page 23 and 24: The Logic PC Board controls the tim
Page 25 and 26: cut being more square than the othe
Page 27 and 28: Set the Power Supply RUN/SET switch
Page 29 and 30: 4. Clogged coolant filter and/or in
Page 31 and 32: a. Check continuity per appropriate
Page 33 and 34: NOTE Art may differ from actual uni
Page 35 and 36: H. Temperature Circuit Test The Pow
Page 37 and 38: ange, check between the two output
Page 39 and 40: SECTION 5: REPLACEMENT PROCEDURES 5
Page 41 and 42: C. Work Cable Replacement 1. Remove
Page 43 and 44: 5.06 Left Side Center Chassis Parts
Page 45 and 46: I. FET/Heatsink Assembly Replacemen
Page 47 and 48: G. Coolant Reservoir Replacement CA
Page 49 and 50: 9. Carefully slide the rear panel o
Page 51 and 52: M. Current Sense PC Board Assembly
Page 53 and 54: E. Motor (M5) / Fan / Pump Replacem
Page 55 and 56: 7. Remove rear panel from unit by c
Page 57 and 58: 6.01 Introduction SECTION 6: PARTS
Page 59 and 60: 6.04 Access Panel Replacement Parts
Page 61 and 62: 3 2 4 6 10 9 9 1 Manual 0-2697 6-5
Page 63 and 64: 12 1 5 4 3 17 10 11 21 10 Manual 0-
Page 65 and 66: 9 A-02278 3 11 10 20 6 5 23x4274 Ma
Page 67: 11 10 4 15 5 9 11 6 10 4 15 5 9 A-0
Page 71 and 72: Pot/LED PC Board Signals APPENDIX 3
Page 73 and 74: J3-10 +12 vdc J3-11 Active Low Sign
Page 75 and 76: J9-1 36 VAC (b) from Logic PC Board
Page 77 and 78: J13-1 Active Low Start signal (Torc
Page 79 and 80: E1 E2 E7 E8 Component Side of PC Bo
Page 81 and 82: FET PC Board Signals (Upper and Low
Page 83 and 84: APPENDIX 11: CURRENT SENSOR PC BOAR
Page 85 and 86: APPENDIX 13: RECOMMENDED ROUTINE MA
Page 87 and 88: NOTE Transformer T3 in earlier prod
Page 89 and 90: NOTE Transformer T3 in earlier prod
Page 91: Art # A-04328
show all

appendix 1 - Victor Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?