appendix 1 - Victor Technologies

More documents

Recommendations

Info

E19 E17 E18 E18 E19 XFMR SEC - OUTPUT + OUTPUT E1 E17 APPENDIX 9: FET PC BOARD LAYOUT E15 E14 MAIN XFMR PRI MAIN XFMR PRI MAIN XFMR SEC E16 FET PCB ASSY 10 1 E16 J6 J6 E15 Component Side Of PC Board E14 E14 E15 Solder Side Of PC Board APPENDIX A-12 Manual 0-2697 E16 E17 E18 E19 T3 A-00479
FET PC Board Signals (Upper and Lower Assemblies) J6-1 +12 vdc from the Gate Drive Board upper J7-1 Lower J8-1 J6-2 +12 vdc RTN from the Gate Drive Board upper J7-2 Lower J8-2 J6-3 PWM Output from the Gate Drive Board upper J7-3 Lower J8-3 J6-4 PWM Output RTN J6-2 from the Gate Drive Board upper J7-4 Lower J8-4 J6-5 PRI CURRENT SENSE to the Gate Drive Board upper J7-5 Lower J8-5 J6-6 PRI CURRENT SENSE RTN to the Gate Drive Board upper J7-6 Lower J8-6 J6-7 SEC CURRENT SENSE to the Gate Drive Board upper J7-7 Lower J8-7 J6-8 SEC CURRENT SENSE RTN to the Gate Drive Board upper J7-8 Lower J8-8 J6-9 OVER TEMP RTN to the Gate Drive Board upper J7-9 Lower J8-9 J6-10 Active Low OVER TEMP Signal to the Gate Drive Board upper J7-10 Lower J8-10 E1 HEATSINK GND To HEAT SINK E14 MAIN XFMR PRI to MAIN XFMR PRI E14 E15 MAIN XFMR PRI to MAIN XFMR PRI E15 E16 MAIN XFMR SEC from MAIN XFMR SEC E16 E17 OUTPUT (-) to OUTPUT INDUCTOR L1 E18 OUTPUT (+) to Current Sense Transformer and E8 on Output Board E19 MAIN XFMR SEC from MAIN XFMR SEC E19 Manual 0-2697 A-13 APPENDIX
Page 1:
PLASMA CUTTING POWER SUPPLY PAK Mas
Page 4 and 5:
TABLE OF CONTENTS SECTION 1: GENERA
Page 7 and 8:
SECTION 1: GENERAL INFORMATION 1.01
Page 9 and 10:
6. ANSI Standard Z49.2, FIRE PREVEN
Page 11 and 12:
ultra-violets très forts. Ces rayo
Page 13 and 14:
1.07 Declaration of Conformity Manu
Page 15 and 16:
SECTION 2: INTRODUCTION 2.01 Scope
Page 17 and 18:
SECTION 3: DESCRIPTION 3.01 Scope o
Page 19 and 20:
15. Weight Power Supply with Torch:
Page 21 and 22:
4.01 Introduction SECTION 4: SERVIC
Page 23 and 24:
The Logic PC Board controls the tim
Page 25 and 26:
cut being more square than the othe
Page 27 and 28:
Set the Power Supply RUN/SET switch
Page 29 and 30: 4. Clogged coolant filter and/or in
Page 31 and 32: a. Check continuity per appropriate
Page 33 and 34: NOTE Art may differ from actual uni
Page 35 and 36: H. Temperature Circuit Test The Pow
Page 37 and 38: ange, check between the two output
Page 39 and 40: SECTION 5: REPLACEMENT PROCEDURES 5
Page 41 and 42: C. Work Cable Replacement 1. Remove
Page 43 and 44: 5.06 Left Side Center Chassis Parts
Page 45 and 46: I. FET/Heatsink Assembly Replacemen
Page 47 and 48: G. Coolant Reservoir Replacement CA
Page 49 and 50: 9. Carefully slide the rear panel o
Page 51 and 52: M. Current Sense PC Board Assembly
Page 53 and 54: E. Motor (M5) / Fan / Pump Replacem
Page 55 and 56: 7. Remove rear panel from unit by c
Page 57 and 58: 6.01 Introduction SECTION 6: PARTS
Page 59 and 60: 6.04 Access Panel Replacement Parts
Page 61 and 62: 3 2 4 6 10 9 9 1 Manual 0-2697 6-5
Page 63 and 64: 12 1 5 4 3 17 10 11 21 10 Manual 0-
Page 65 and 66: 9 A-02278 3 11 10 20 6 5 23x4274 Ma
Page 67 and 68: 11 10 4 15 5 9 11 6 10 4 15 5 9 A-0
Page 69 and 70: APPENDIX 1: INPUT WIRING REQUIREMEN
Page 71 and 72: Pot/LED PC Board Signals APPENDIX 3
Page 73 and 74: J3-10 +12 vdc J3-11 Active Low Sign
Page 75 and 76: J9-1 36 VAC (b) from Logic PC Board
Page 77 and 78: J13-1 Active Low Start signal (Torc
Page 79: E1 E2 E7 E8 Component Side of PC Bo
Page 83 and 84: APPENDIX 11: CURRENT SENSOR PC BOAR
Page 85 and 86: APPENDIX 13: RECOMMENDED ROUTINE MA
Page 87 and 88: NOTE Transformer T3 in earlier prod
Page 89 and 90: NOTE Transformer T3 in earlier prod
Page 91: Art # A-04328
show all

appendix 1 - Victor Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?