Therma-Tru Slim-Line Sliding Patio Door Assembly and Installation

More documents

Recommendations

Info

4D 5D INSERT PANEL BUMPER Insert panel bumper into innermost channel in head jamb, butting end of bumper against stationary side jamb. Seat panel bumper flush with head jamb. 6D INSTALL ASTRAGAL & KEEPER Assemble the parts shown below to the astragal with 4 #10 - 32 x 1 1/4" PPH SS MS. Install the top and bottom of the astragal and work towards the center. Note the notched portion goes at the bottom of the slab. Take caution to align the astragal with the bottom of the panel. #10-32 x 1 1/4" PPH SS MS Keeper 35 Panel Bumper Nylon Strike Spacer Astragal Interior Side Side Jamb SS Strike Backer Head Jamb Panel Bumper NOTE: IF NEEDED THE BUMPER CAN BE CUT DOWN FROM ITS ORIGINAL LENGTH OF SIX INCHES TO FOUR AND A HALF INCHES. THIS WILL ALLOW FOR A WIDER ENTRANCE. HANDLE AND MORTISE LOCK INSTALLATION Follow steps 21 - 23 then 25 - 27 to complete the handle and mortise lock installation.
7D PASSIVE HANDLE INSTALL A. Assemble handle to escutcheon plate according to the hand of the door, with two hex screws. The curve of the handle should slope toward the center of the slab it is being installed into. Tighten securely to prevent loosening during operation. B. The black foam gasket should be installed under the exterior escutcheon plate. This piece will prevent water infiltration. C. Insert through pin into escutcheon plate. D. Place exterior handle on door aligning holes in panel. 8D Escutcheon ALIGN INTERIOR HANDLE Handle 36 Exterior A. Assemble handle to escutcheon plate according to the hand of the door, with two hex screws. The curve of the handle should slope toward the center of the door. Tighten securely to prevent loosening during operation. B. If desired, the thumb knob can be changed to different positions when in the locked and unlocked positions. To do this, remove the screw in the stem of the thumb turn. Next, rotate the adaptor so the desired threaded hole in the adaptor lines up with a hole in the thumb turn stem. C. Place interior handle over latch aligning holes in panel. D. Fasten handles together with (2) phillips pan head colored screws. Tighten the mounting screws to complete the installation. NOTE: USE CAUTION NOT TO OVER TIGHTEN SCREWS. Gasket (2) 2" Phillips Pan Head Colored Screws
Page 1 and 2: Therma-Tru Slim-Line Sliding Patio
Page 3 and 4: ® The following packages are neede
Page 5 and 6: 3 ATTACH HEAD TO JAMBS 4 DRIP CAP I
Page 7 and 8: 5 4 APPLY SILICONE SEALANT TO BOTTO
Page 9 and 10: 9 10 PLUMB SIDE JAMBS Jambs must be
Page 11 and 12: 13 15 INSTALL ANCHOR TO THE INACTIV
Page 13 and 14: 19 20 ATTACH ACTIVE WEATHERSTRIP CA
Page 15 and 16: 24 25 INSTALL KEEPER Align keeper t
Page 17 and 18: 28 29 SLIDING SCREEN DOOR Refer to
Page 19 and 20: 1A 2A Assembly NOTE: A large work a
Page 21 and 22: 5A APPLY SEALANT TO SILL Apply a co
Page 23 and 24: 10A 11A ATTACH M.E.U. TO TWO PANEL
Page 25 and 26: Transom Transom ® The following pa
Page 27 and 28: 4B ATTACH TRANSOM TO PATIO UNIT A.
Page 29 and 30: 6B INDEPENDENT INSTALLATION Turn to
Page 31 and 32: 1C FRAME ASSEMBLY Proceed to page 3
Page 33 and 34: 7C INSERT PANEL BUMPER Insert panel
Page 35: 1D FRAME ASSEMBLY STEPS 1 -11 Proce
Page 39 and 40: A B JAMB EXTENSION INFORMATION The
Page 41 and 42: D TRIPLE SYSTEM INFORMATION The int
Page 43 and 44: R.H. = Replacement Height SL = Side
Page 45: 1687 Woodlands Dr. Maumee, OH 43537

Therma-Tru Slim-Line Sliding Patio Door Assembly and Installation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?