Therma-Tru Slim-Line Sliding Patio Door Assembly and Installation

More documents

Recommendations

Info

C INTERIOR CASING ATTACHMENT Interior casing may be attached to the Slim-Line frame in either of the following ways. An air nailer can be used to fasten the interior casing to the Slim-Line frame using 0.050” x 1-½" wire brad nails through the casing and fiberglass frame. For maximum holding power, ensure that nails are installed through anchor blocks located within frame profiles. Locations are shown below for standard two-panel systems. For manual application, we suggest using 4d-1-½" finish nails. They can be used to secure interior casing to the frame. Pre-drilled pilot holes (1/16" dia.) are recommended to avoid splitting casing or frame. Ensure that nails are installed through anchor blocks for maximum holding power. 5" 5" 1" 5" 6 1/4" System Center Line 5" Lock Center Line 39 6 1/4" 5" 5" 5"
D TRIPLE SYSTEM INFORMATION The intention of this section is to clarify the differences between a triple mulled and triple continuous Slim-Line Patio Door System. Handing Configurations for a Mulled Triple: FLF (Fixed, Left Hand Active, Fixed) FRF (Fixed, Right Hand Active, Fixed) LFF* (Left Hand Active, Fixed, Fixed) FFR* (Fixed, Fixed, Right Hand Active) Handing Configurations for a Continuous Triple: LFF (Left Hand Active, Fixed, Fixed) FFR (Fixed, Fixed, Right Hand Active) * When ordering a LFF or FFR patio door the continuous configuration will be used as the automatic default. If a LFF or FFR is needed in a mulled configuration it can be ordered as a double and a multiple extension system and then joined in the field. Please note that the overall width of a mulled system is different then that of a continuous system. Another significant difference between a mulled triple and a continuous triple is the packaging. A triple continuous system will be shipped in two uni-boxes and a long frame box. In comparison, a mulled system will ship in just two boxes. TRIPLE CONTINUOUS PATIO DOOR LFF SHOWN 40 TRIPLE MULLED PATIO DOOR FRF SHOWN
Page 1 and 2: Therma-Tru Slim-Line Sliding Patio
Page 3 and 4: ® The following packages are neede
Page 5 and 6: 3 ATTACH HEAD TO JAMBS 4 DRIP CAP I
Page 7 and 8: 5 4 APPLY SILICONE SEALANT TO BOTTO
Page 9 and 10: 9 10 PLUMB SIDE JAMBS Jambs must be
Page 11 and 12: 13 15 INSTALL ANCHOR TO THE INACTIV
Page 13 and 14: 19 20 ATTACH ACTIVE WEATHERSTRIP CA
Page 15 and 16: 24 25 INSTALL KEEPER Align keeper t
Page 17 and 18: 28 29 SLIDING SCREEN DOOR Refer to
Page 19 and 20: 1A 2A Assembly NOTE: A large work a
Page 21 and 22: 5A APPLY SEALANT TO SILL Apply a co
Page 23 and 24: 10A 11A ATTACH M.E.U. TO TWO PANEL
Page 25 and 26: Transom Transom ® The following pa
Page 27 and 28: 4B ATTACH TRANSOM TO PATIO UNIT A.
Page 29 and 30: 6B INDEPENDENT INSTALLATION Turn to
Page 31 and 32: 1C FRAME ASSEMBLY Proceed to page 3
Page 33 and 34: 7C INSERT PANEL BUMPER Insert panel
Page 35 and 36: 1D FRAME ASSEMBLY STEPS 1 -11 Proce
Page 37 and 38: 7D PASSIVE HANDLE INSTALL A. Assemb
Page 39: A B JAMB EXTENSION INFORMATION The
Page 43 and 44: R.H. = Replacement Height SL = Side
Page 45: 1687 Woodlands Dr. Maumee, OH 43537

Therma-Tru Slim-Line Sliding Patio Door Assembly and Installation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?