HP Server Migration Pack – Universal Edition User Guide - Index of

More documents

Recommendations

Info

4. If the destination server is booted to the SMP Boot CD and the destination agent is launched, select Destination server is already booted with boot CD. Enter the four-part IP address for the destination server (that was identified when booting the destination server), and then click Next. Using SMP Universal for server migration 48
5. If the destination server is not booted to the SMP Boot CD and the destination agent is not launched, select Boot destination server automatically. Enter the four-part iLO IP address and the iLO administrative credentials, and then click Boot Destination Server. 6. Click Launch iLO and then open the remote console to provide onscreen information, such as language, IP address, and so on to launch the SMP Agent on the destination server. To cancel the booting job, click Cancel Booting. After the boot job finishes, a new textbox appears. Enter the destination four-part IP address that is acquired after the destination agent is launched on the destination server, and then click Next. 7. Test the network connections and latency between the source-to-destination server and the application-station-to-destination server. The results of a 2-second test appear initially. 8. Select a test time in the lower portion of the wizard screen to perform additional tests, and then click Test. The following test times are available: ○ 2 seconds ○ 5 seconds ○ 10 seconds ○ 30 seconds ○ 60 seconds If the source-to-destination or application-station-to-destination connection cannot be established, then the Next button is disabled. Ensure that ports 51125 and 51126 are open between source and destination servers. If the source-to-destination or application-station-to-destination connection is established, but the network reports a transfer speed below 250 kbps, then the Next button is disabled. If the source-to-destination or application-station-to-destination connection is established and the network test reports a transfer speed of at least 250 kbps, then the Next button is enabled. Using SMP Universal for server migration 49
Page 1 and 2: HP Server Migration Pack - Universa
Page 3 and 4: Contents 1 Introduction............
Page 5 and 6: Microsoft DNS Server might not map
Page 7 and 8: 1 Introduction Server Migration Pac
Page 9 and 10: Supported destination ProLiant serv
Page 11 and 12: Firewalls The Microsoft Windows® f
Page 13 and 14: ProLiant Support Pack IMPORTANT: Th
Page 15 and 16: Source servers The physical or virt
Page 17 and 18: 4. Read the license agreement. Sele
Page 19 and 20: Changing the default SMP Universal
Page 21 and 22: • VMware ESX Server 3.0.1 • VMw
Page 23 and 24: To deploy the SMP Universal Agent t
Page 25 and 26: 3. In the IP Address, User Name, an
Page 27 and 28: 3. To launch the SMP Source Agent,
Page 29 and 30: Manually booting a physical destina
Page 31 and 32: 6. If the application is unable to
Page 33 and 34: 6. You can set the duplex settings
Page 35 and 36: SMP Universal overview screen After
Page 37 and 38: 4 Licensing SMP Universal licensing
Page 39 and 40: SMP 2.x and P2P license conversion
Page 41 and 42: Using License Migration Tool to mig
Page 43 and 44: Concurrent and queued migrations Co
Page 45 and 46: 8. Disable all applications and bac
Page 47: 3. Select the volumes to be migrate
Page 51 and 52: 10. Map source disks to destination
Page 53 and 54: 13. Review and confirm the migratio
Page 55 and 56: 9. If necessary, convert basic disk
Page 57 and 58: HP SMP Universal application statio
Page 59 and 60: Volumes on dynamic disks are migrat
Page 61 and 62: This screen appears for HP Integrat
Page 63 and 64: − If the destination virtual mach
Page 65 and 66: If you are migrating to a non-embed
Page 67 and 68: 8. Click Next. 9. Select the post-m
Page 69 and 70: 11. Review the migration progress d
Page 71 and 72: Virtual-to-virtual migrations A vir
Page 73 and 74: Performing a V2V migration CAUTION:
Page 75 and 76: 4. Enter the four-part IP address o
Page 77 and 78: This screen appears for HP integrat
Page 79 and 80: If you are migrating to a non-embed
Page 81 and 82: 8. Click Next. 9. Select the post-m
Page 85 and 86: Virtual-to-ProLiant migrations A vi
Page 87 and 88: Performing a V2P migration CAUTION:
Page 89 and 90: The table on the lower part of the
Page 91 and 92: NOTE: If the application-station-to
Page 93 and 94: 11. Select the following migration
Page 97 and 98: ○ Configuration of the HBA BIOS.
Page 99 and 100:
3. If in step 1 of a migration alre
Page 101 and 102:
4. If a security alert appears, the
Page 103 and 104:
○ From All Systems page in the HP
Page 105 and 106:
2. Click the Software tab, and then
Page 107 and 108:
5. To begin the installation, click
Page 109 and 110:
3. To install the PSP on the local
Page 111 and 112:
6 Viewing migration logs To view mi
Page 113 and 114:
8 Troubleshooting This section iden
Page 115 and 116:
6. For all Emulex HBA devices seen
Page 117 and 118:
Deploy Agent task to Windows fails
Page 119 and 120:
Drives do not display on the migrat
Page 121 and 122:
For Windows 2000 Server systems: 1.
Page 123 and 124:
Corrective action is required for s
Page 125 and 126:
Supported storage controllers displ
Page 127 and 128:
For Windows 2000 1. From the Contro
Page 129 and 130:
1. Restart the SMP Universal Agent
Page 131 and 132:
• Obtain the latest SmartStart Re
Page 133 and 134:
Glossary console operating system (
Page 135 and 136:
do not display on migrated operatin
Page 137 and 138:
R related products, 13 requirements
show all

HP Server Migration Pack – Universal Edition User Guide - Index of

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?