Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Parameter Index and Modbus addresses<br />
Code Page Name Unit<br />
LI* Logical inputs<br />
LI2 60 Logic input 2 -<br />
LI3 60 Logic input 3 -<br />
Lo 47<br />
OIt 57<br />
OId 56<br />
OSd 59<br />
OSt 58<br />
Logic Output relays<br />
status<br />
Overcurrent time<br />
delay<br />
Overcurrent<br />
threshold<br />
Over voltage<br />
threshold<br />
Under voltage time<br />
delay<br />
(1) Modbus code = Soft starter message<br />
example : oFF on the soft starter will be equivalent to "0" with Modbus protocol (remote command)<br />
* : parameter visible only with Modbus<br />
Modbus<br />
code and<br />
Adjustment<br />
Range (1)<br />
d0: Input 1. 0 – open, 1 – closed.<br />
d1: Input 2.<br />
d2: Input 3.<br />
d3...d15: Reserved<br />
0 = Strt<br />
1 = rUn<br />
2 = 2nd<br />
3 = EtF<br />
4 = rSt<br />
5 = FAn<br />
6 = FI<br />
7 = LIL<br />
2 = 2nd<br />
3 = EtF<br />
4 = rSt<br />
5 = FAn<br />
6 = FI<br />
7 = LIL<br />
Description<br />
start:for a 3-wire control<br />
run:for a 2-wire control<br />
2nd set of parameters<br />
external detected fault<br />
remote reset<br />
fan control<br />
trip inhibition<br />
forced local command<br />
2nd set of parameters<br />
external detected fault<br />
remote reset<br />
fan control<br />
trip inhibition<br />
forced local command<br />
d0: Relay 1. 0 – not energized, 1 - energized<br />
d1: Relay 2<br />
d2...d15: reserved<br />
s 0 to 50 s<br />
%<br />
ofIn<br />
%<br />
of Uln<br />
100 to 300, by<br />
increment of 5<br />
PG* Proportional gain % 0 to 100%<br />
PHL 58<br />
Phase loss<br />
detection<br />
PHr 57 Phase sequence -<br />
PtC 59<br />
PTC probes motor<br />
monitoring<br />
5 with Modbus = 0.5s<br />
50 with Modbus = 5.0s<br />
Modbus<br />
address<br />
261<br />
Factory<br />
setting<br />
72 rUn<br />
73 rSt<br />
262<br />
51 0.5<br />
- 50 200<br />
110 to 125 - 60 120<br />
s 1 to 10 - 61 2<br />
-<br />
-<br />
0 = oFF<br />
1 = On<br />
0 = 123<br />
1 = 321<br />
2 = oFF<br />
0 = oFF<br />
1 = On<br />
This parameter is reserved<br />
for expert mode.<br />
Active when SSC = On<br />
off<br />
on<br />
123<br />
321<br />
off<br />
off<br />
on<br />
37 60<br />
57 On<br />
56 oFF<br />
62 oFF<br />
User<br />
setting<br />
79
Change language