cmd6686gx manual - RTD Embedded Technologies, Inc.

More documents

Recommendations

Info

Entering the BIOS Setup • Apply power to the system • Repeatedly press the DEL key to enter setup • Another way applies if you have a floppy attached. When the floppy is accessed for the first time (a sound will come from the floppy) press the DEL key once. 52
Default Configuration In addition to the Setup configuration stored on the board, the cpuModule has a permanent default configuration. The system will resort to using this default if an error occurs when accessing the EPROM which holds the Setup on the module. The default configuration is listed below. BIOS Default Configuration Function Default selection IDE Interface 0 Master Auto detect IDE Interface 0 Slave Auto detect IDE Interface 1 Master Auto detect IDE Interface 1 Slave Auto detect Boot device Floppy then hard disk BIOS Extension Disabled Floppy Drive 1 3.5" 1.44 Meg Floppy Drive 2 not installed Serial port 1 RS232 at 3F8H Serial port 2 RS232 at 2F8H Parallel Port LPT1 at 378H Keyboard Enabled if connected USB Enable if connected Fail safe boot rom Enabled NOTE! Boards are shipped with fail safe boot rom enable. See the chapter on Configuring the cpuModule (BIOS setup) in Disabling Fail Safe Boot ROM for the method to disable it. When Fail Safe Boot ROM is enabled the system will boot to it exclusively. 53
Page 1: CMD6686GX cpuModule TM User’s Man
Page 4 and 5: Revision History 99.03.30 New 99.07
Page 6 and 7: Parallel Port Control .............
Page 8 and 9: The CMD6686GX cpuModule The PC/104
Page 10 and 11: Solid State Disk Socket • SSD soc
Page 13 and 14: CHAPTER 2: GETTING STARTED For many
Page 15 and 16: CN17 USB Connector 10 pin For a com
Page 17 and 18: Cable Kits For maximum flexibility,
Page 19 and 20: Connecting the utility cable The Mu
Page 21 and 22: Connecting to the PC/104 Bus The PC
Page 23 and 24: Booting to Boot Block Flash with Fa
Page 25: For More Information This chapter h
Page 28: I/O Connections The cpuModule comes
Page 31 and 32: CMD6686GX Connector Locations NOTE!
Page 33 and 34: Facing the connector pins, the pino
Page 35 and 36: Facing the serial port’s connecto
Page 37 and 38: Serial Port 2, CN8 The second seria
Page 39 and 40: Connector CN8 in RS-422/485 Mode 5
Page 41 and 42: Parallel Port Connector, CN6 21 BSY
Page 43 and 44: Keyboard Connector Pins on CN5 Pin
Page 45 and 46: USB Connector,CN17 Two USB ports ar
Page 47 and 48: The following table lists signals o
Page 49 and 50: PC/104 Bus Signals MASTER* I During
Page 51: CHAPTER 4: CONFIGURING THE CPUMODUL
Page 55 and 56: Installing SSD Memory This section
Page 57 and 58: Main Menu Setup Fields The followin
Page 59 and 60: BIOS Features Setup The following i
Page 61 and 62: Cyrix 6x86/MII CPUID BIOS Features
Page 63 and 64: Power Management Setup Fields The f
Page 65 and 66: Power Management Setup Fields IRQ t
Page 67 and 68: PNP/PCI Configuration Setup Fields
Page 69 and 70: Integrated Peripherals Setup Fields
Page 71: Exit Setup Fields The following is
Page 74 and 75: Memory Map The module addresses mem
Page 76 and 77: 2 Only one of the I/O addresses sho
Page 78 and 79: The RTD Enhanced Award BIOS The RTD
Page 80 and 81: Cannot initialize controller. Make
Page 82 and 83: RTD Enhanced Award BIOS POST Codes
Page 84 and 85: RTD Enhanced Award BIOS POST Codes
Page 86 and 87: Bypassing the Stored Configuration
Page 88 and 89: Watchdog Timer Control The cpuModul
Page 90 and 91: Parallel Port Control The parallel
Page 92 and 93: Storing Applications On-board The c
Page 95 and 96: BIOS Extension Devices You can use
Page 97: Directly Accessing the Solid State
Page 100 and 101: Jumpers Many cpuModule options are
Page 102 and 103:
JP2 2-pin jumper Open (no terminati
Page 104 and 105:
686GX233 or 686GX300 Processor Ther
Page 106 and 107:
Common Problems and Solutions The f
Page 108 and 109:
two hard drives will not work, but
Page 110 and 111:
How to Obtain Technical Support If
Page 112 and 113:
112
Page 114:
Real Time Devices USA, Inc. P.O. Bo
show all

cmd6686gx manual - RTD Embedded Technologies, Inc.

Create successful ePaper yourself

Delete template?

Save as template?