User Guide and Manual for Project Canary

More documents

Recommendations

Info

3.5: Dashboard Tab: Graphs The “Graphs” link on the Dashboard page brings up a popup window that looks like this on a typical data center server: The graphs for a typical Sun Ray (or other multiuser) server look quite different: User Guide and Manual for Project Canary Page 20
Each of the graphs shown in the previous images are clickable and will bring up another popup window with a zoomed-in view of that particular graph. Raw datafiles are available by clicking the “Raw Data Files” link or User Guide and Manual for Project Canary Page 21
Page 1 and 2: User Guide and Manual for Project C
Page 3 and 4: Chapter 1: Project Canary Overview.
Page 5 and 6: 4.13: Graph PID[s] Report..........
Page 7 and 8: 4. /usr/bin/uptime 5. /usr/bin/prst
Page 9 and 10: client being monitored. A ten minut
Page 11 and 12: On this page, one sees a basic guid
Page 13 and 14: Here one can access the various rep
Page 15 and 16: By default, servers are grouped int
Page 17 and 18: As shown above, clicking on a “Ca
Page 19: This page shows when the Project Ca
Page 23 and 24: Scrolling down on the page will rev
Page 25 and 26: Below is a graph taken from a typic
Page 27 and 28: The Blue line shows how many iterat
Page 29 and 30: This graph shows how many interrupt
Page 31 and 32: On a Sun Ray server with multiple u
Page 33 and 34: using it. If the red CPU utilizatio
Page 35 and 36: A Sun Ray server or diskless workst
Page 37 and 38: perform cross-architecture communic
Page 39 and 40: The X-axis shows the number of proc
Page 41 and 42: These statistics are collected from
Page 43 and 44: Note again, there are spikes at nig
Page 45 and 46: The network appears to be fairly sp
Page 47 and 48: From this graph, it would appear th
Page 49 and 50: The Data Center server is not runni
Page 51 and 52: Since the data center server is not
Page 53 and 54: The graph above shows that the data
Page 55 and 56: As the previous graphs have shown,
Page 57 and 58: Older versions of Sun Ray Server So
Page 59 and 60: When clicking on the Reports Tab, o
Page 61 and 62: The above is an example. To create
Page 63 and 64: From this screen, one must select a
Page 65 and 66: As described previously, this table
Page 67 and 68: This report is identical to the “
Page 69 and 70: The CPU Load (animated) report show
Page 71 and 72:
systems administrator is advised to
Page 73 and 74:
There are four reports on various c
Page 75 and 76:
As described earlier in this docume
Page 77 and 78:
As with all reports available from
Page 79 and 80:
This graph is useful to see if the
Page 81 and 82:
This chart is useful for monitoring
Page 83 and 84:
As shown above, users who have logi
Page 85 and 86:
From the graph shown on the previou
Page 87 and 88:
as CDE and GNOME which have been se
Page 89 and 90:
4.11.4: Total Resident Memory Consu
Page 91 and 92:
4.11.6: Total CPU Minutes Used for
Page 93 and 94:
4.11.8: Percentage of memory consum
Page 95 and 96:
4.11.10: Total resident memory cons
Page 97 and 98:
4.11.12: Total CPU minutes consumed
Page 99 and 100:
4.11.14: Percentage of server memor
Page 101 and 102:
Also note the power-user at the end
Page 103 and 104:
4.11.18: Total CPU minutes for all
Page 105 and 106:
The CPU Profiles report page looks
Page 107 and 108:
Note that peaks and valleys appear
Page 109 and 110:
As with the automount png graph des
Page 111 and 112:
Note that while ncsd doesn't appear
Page 113 and 114:
Here on this graph, it is shown tha
Page 115 and 116:
utdsd, like other system service da
Page 117 and 118:
The main purpose of this report is
Page 119 and 120:
Overview of Project Canary Software
Page 121 and 122:
management system. A2.2: I don't wa
Page 123 and 124:
Crypto 74 Crypto Settings report 78
Page 125 and 126:
unaway processes 9, 12, 16, 23p., 6
show all

User Guide and Manual for Project Canary

Create successful ePaper yourself

Delete template?

Save as template?