3000 Series Articulator and Quick Mount Face-Bow ... - Whip Mix

More documents

Recommendations

Info

Fig. 53 Note: Set each condylar guide to 30° on the condylar inclination scale in preparation for attaching the face-bow assembly to the upper frame of the articulator. Fig. 54 Tighten the black clamp knob while pressing the condylar guide assembly against the upper frame of the articulator. Fig. 55 Set each progressive side shift guide setting to the “0” mark and tighten the side shift locking screw. Fig. 56 Place clean Mounting Plates on the upper and lower frames. The Quick Magnetic Mounting System is shown here. 22
Fig. 57 Place metal disk into plastic mounting plate and attach to articulator. If using standard screw-type mounting plates, firmly tighten the #8508 Mounting Plate knob when securing a mounting plate to the articulator. Fig. 58 Two screw-type mounting plates are available. Plastic #8580B Mounting Plates are an economical alternative to metal mounting plates. They are designed to be utilized for one case. Metal mounting plates are rigid and reusable. The articulator is now ready to have the face-bow secured to its upper frame. II. Placing A Direct Mounting Face-Bow On The Articulator Fig. 59 Slide the plastic nasion relator assembly to the patients left, away from the center of the horizontal crossbar of the facebow if this has not already been done. Loosen the center thumb screw on the top of the face-bow. Note: A rubber band properly positioned aids in manipulation. If using the original metal face-bow, loosen the three thumb screws on top of the face-bow. 23
Page 1 and 2: 3000 Series Articulator and Quick M
Page 3 and 4: CONTENTS INTRODUCTION 5 OBTAINING F
Page 5 and 6: INTRODUCTION WHIP MIX Articulators
Page 7 and 8: Fig. 5 Loosen the #8604 Thumb Screw
Page 9 and 10: Fig. 13 Inspect the registration fo
Page 11 and 12: Fig. 20 Tighten the center #8604 Th
Page 13 and 14: V. Obtaining Interocclusal Records
Page 15 and 16: Fig. 34 Remove and examine the cent
Page 17 and 18: Fig. 41 Manipulate the mandible int
Page 20 and 21: DIRECT Mounting THE MAXILLARY Cast
Page 24 and 25: Fig. 60 Hold the face-bow in one ha
Page 26 and 27: Fig. 68 The #28706 Face-Bow Fork Su
Page 28 and 29: INDIRECT Mounting THE MAXILLARY Cas
Page 30 and 31: I. Preparing The Face-Bow And Artic
Page 32 and 33: III. Mounting The Maxillary Cast Fi
Page 34 and 35: Fig. 97 Place the articulator upsid
Page 36 and 37: Setting The Condylar Guidance Of Th
Page 38 and 39: Fig. 112 Tighten the #2432 Clamp Kn
Page 40 and 41: SeTTING THE CONDYLAR GUIDANCE OF TH
Page 42 and 43: Fig. 127 To prevent possible wearin
Page 44 and 45: III. Preparing Face-Bow Armamentari
Page 46 and 47: VI. Preparing The Articulator For M
Page 48 and 49: VIII. Mounting The Mandibular Cast
Page 50 and 51: Fig. 159 Set condylar inclinations
Page 52 and 53: Interchangeability With The Model 3
Page 54 and 55: Maintenance The Whip Mix Model 3040
Page 56 and 57: Model 3140 Articulator # PART# QTY.
Page 58 and 59: model 9600 face-bow For Direct Moun
Page 60 and 61: MODELS 9275/ 9285/9295 FACE-BOWS FO
Page 62 and 63: NOTES _____________________________
Page 64: For additional information, contact

3000 Series Articulator and Quick Mount Face-Bow ... - Whip Mix

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?