3000 Series Articulator and Quick Mount Face-Bow ... - Whip Mix

More documents

Recommendations

Info

Fig. 127 To prevent possible wearing away of the stone casts during manipulation of the articulator, or to make a permanent record of a specific case, the natural incisal guidance may be recorded. This is done by adding a layer of self-curing resin to the #8526F Plastic Incisal Guide Table and forming the guidance path into the resin as it cures. Figure shows materials needed for fabrication of a custom incisal guide table. Fig. 128 1. Raise the incisal guide pin 1–2 mm. 2. Lubricate the rounded end of the incisal guide pin. Next, moisten the surface of the incisal guide table with 1–2 drops of self-curing acrylic monomer. 3. Mix enough acrylic to place approximately 1/4” on the top of the incisal guide table. 4. Once the acrylic is in a doughy state, place the acrylic on the table. Fig. 129 5. Carefully, close the articulator in centric position. 6. Move the upper frame of the articulator back to simulate a straight protrusive movement (end to end). 7. From centric, move the upper member of the articulator to give a straight right lateral movement. 8. Then, move the upper member of the articulator to give a straight left lateral movement. 9. Move through all intermediate excursions between the lateral and protrusive positions. Allow the acrylic to harden and trim off excess acrylic. Fig. 130 The #8533 Dovetail Incisal Block is a convenient accessory designed so a custom acrylic guide may be easily removed and can later be easily replaced. Its dovetail sides and centering screw assure the user of accurate repositioning time after time. 42
COMPLETE Denture Technique (shown on Model 2240 Articulator) I. Constructing Occlusion Rims Fig. 131 Having obtained a master cast, wax occlusion rims should be formed on well-adapted record bases (base plates) for the upper and lower arches. After examination of the upper record base in the patient’s mouth, adjust the base plate, if necessary. Contour the upper and lower occlusion rims, establish occlusal vertical dimension and plane of orientation. Fig. 132 Create wedge-shaped V indices in the wax occlusion rims. II. Preparing The Face-Bow Fork Fig. 133 Apply vinylpolysiloxane (VPS) adhesive to a properly sterilized bite fork. Note: Adhesive not mandatory when using perforated bite fork. Fig. 134 Some clinicians prefer to utilize a pronged bite fork. 43
Page 1 and 2: 3000 Series Articulator and Quick M
Page 3 and 4: CONTENTS INTRODUCTION 5 OBTAINING F
Page 5 and 6: INTRODUCTION WHIP MIX Articulators
Page 7 and 8: Fig. 5 Loosen the #8604 Thumb Screw
Page 9 and 10: Fig. 13 Inspect the registration fo
Page 11 and 12: Fig. 20 Tighten the center #8604 Th
Page 13 and 14: V. Obtaining Interocclusal Records
Page 15 and 16: Fig. 34 Remove and examine the cent
Page 17 and 18: Fig. 41 Manipulate the mandible int
Page 20 and 21: DIRECT Mounting THE MAXILLARY Cast
Page 22 and 23: Fig. 53 Note: Set each condylar gui
Page 24 and 25: Fig. 60 Hold the face-bow in one ha
Page 26 and 27: Fig. 68 The #28706 Face-Bow Fork Su
Page 28 and 29: INDIRECT Mounting THE MAXILLARY Cas
Page 30 and 31: I. Preparing The Face-Bow And Artic
Page 32 and 33: III. Mounting The Maxillary Cast Fi
Page 34 and 35: Fig. 97 Place the articulator upsid
Page 36 and 37: Setting The Condylar Guidance Of Th
Page 38 and 39: Fig. 112 Tighten the #2432 Clamp Kn
Page 40 and 41: SeTTING THE CONDYLAR GUIDANCE OF TH
Page 44 and 45: III. Preparing Face-Bow Armamentari
Page 46 and 47: VI. Preparing The Articulator For M
Page 48 and 49: VIII. Mounting The Mandibular Cast
Page 50 and 51: Fig. 159 Set condylar inclinations
Page 52 and 53: Interchangeability With The Model 3
Page 54 and 55: Maintenance The Whip Mix Model 3040
Page 56 and 57: Model 3140 Articulator # PART# QTY.
Page 58 and 59: model 9600 face-bow For Direct Moun
Page 60 and 61: MODELS 9275/ 9285/9295 FACE-BOWS FO
Page 62 and 63: NOTES _____________________________
Page 64: For additional information, contact

3000 Series Articulator and Quick Mount Face-Bow ... - Whip Mix

Create successful ePaper yourself

Delete template?

Save as template?