3000 Series Articulator and Quick Mount Face-Bow ... - Whip Mix

More documents

Recommendations

Info

VI. Preparing The Articulator For Mounting Casts Fig. 143 Many operators prefer to replace the plastic incisal guide block with an adjustable metal table, such as the #2460 Adjustable Guide Table (shown). Fig. 144 To install the adjustable guide table, remove the #8526F Plastic Incisal Guide from the articulator. Slide the adjustable table into the thumb screw slot in the lower frame of the articulator and tighten the thumb screw. Fig. 145 Adjust the position of the adjustable guide table until the chiseled end of the incisal guide pin lies directly over the scribed line on the guide table. Note: Guide pin must be set at “0” on upper member. VII. Mounting The Maxillary Cast Fig. 146 The indirect technique of mounting the maxillary cast will be demonstrated. However, the direct mounting technique may also be used to mount the maxillary edentulous cast. The transfer assembly has been removed from the face-bow and the support bar is placed into position. 46
Fig. 147 The QUICK MOUNT transfer base has been placed onto the lower member of the articulator and is held in position by the QUICK MOUNT cast support. The transfer assembly is inserted into the transfer base and the clamp is securely tightened. Fig. 148 The QUICK MOUNT cast support is adjusted until it lightly makes contact with the bottom of the bite fork. Fig. 149 The cast is placed into the occlusion rim, which is then seated into the registration on the bite fork. The assembly is now completed and ready for the addition of Whip Mix MOUNTING STONE. Fig. 150 The completed mounted maxillary cast. The transfer assembly and transfer base may be removed and the incisal guide pin replaced. 47
Page 1 and 2: 3000 Series Articulator and Quick M
Page 3 and 4: CONTENTS INTRODUCTION 5 OBTAINING F
Page 5 and 6: INTRODUCTION WHIP MIX Articulators
Page 7 and 8: Fig. 5 Loosen the #8604 Thumb Screw
Page 9 and 10: Fig. 13 Inspect the registration fo
Page 11 and 12: Fig. 20 Tighten the center #8604 Th
Page 13 and 14: V. Obtaining Interocclusal Records
Page 15 and 16: Fig. 34 Remove and examine the cent
Page 17 and 18: Fig. 41 Manipulate the mandible int
Page 20 and 21: DIRECT Mounting THE MAXILLARY Cast
Page 22 and 23: Fig. 53 Note: Set each condylar gui
Page 24 and 25: Fig. 60 Hold the face-bow in one ha
Page 26 and 27: Fig. 68 The #28706 Face-Bow Fork Su
Page 28 and 29: INDIRECT Mounting THE MAXILLARY Cas
Page 30 and 31: I. Preparing The Face-Bow And Artic
Page 32 and 33: III. Mounting The Maxillary Cast Fi
Page 34 and 35: Fig. 97 Place the articulator upsid
Page 36 and 37: Setting The Condylar Guidance Of Th
Page 38 and 39: Fig. 112 Tighten the #2432 Clamp Kn
Page 40 and 41: SeTTING THE CONDYLAR GUIDANCE OF TH
Page 42 and 43: Fig. 127 To prevent possible wearin
Page 44 and 45: III. Preparing Face-Bow Armamentari
Page 48 and 49: VIII. Mounting The Mandibular Cast
Page 50 and 51: Fig. 159 Set condylar inclinations
Page 52 and 53: Interchangeability With The Model 3
Page 54 and 55: Maintenance The Whip Mix Model 3040
Page 56 and 57: Model 3140 Articulator # PART# QTY.
Page 58 and 59: model 9600 face-bow For Direct Moun
Page 60 and 61: MODELS 9275/ 9285/9295 FACE-BOWS FO
Page 62 and 63: NOTES _____________________________
Page 64: For additional information, contact

3000 Series Articulator and Quick Mount Face-Bow ... - Whip Mix

Create successful ePaper yourself

Delete template?

Save as template?