Valent_IOM_Controls - RJI-Sales.com

More documents

Recommendations

Info

Table of Contents Safety ............................................................................................................................................................................................... 3 Special Design Requests ............................................................................................................................................................... 3 Warranty Documentation ............................................................................................................................................................... 4 I/O Configuration............................................................................................................................................................................. 5 Universal Inputs............................................................................................................................................................................ 5 Digital Outputs ............................................................................................................................................................................ 10 Analog Outputs........................................................................................................................................................................... 11 LCD Settings ................................................................................................................................................................................. 12 Basic Functions .......................................................................................................................................................................... 13 Advance Adjustment................................................................................................................................................................... 17 Setpoint Descriptors ................................................................................................................................................................... 18 Universal Maintenance Tool (UMT) Settings.............................................................................................................................. 45 Basic Functions .......................................................................................................................................................................... 47 Advanced Functions ................................................................................................................................................................... 49 NDIO Network ............................................................................................................................................................................ 53 BACnet IP Communication Guide............................................................................................................................................. 102 BACnet IP Points List ............................................................................................................................................................... 104 BACnet MSTP Communication Guide ...................................................................................................................................... 107 BACnet MSTP Points List......................................................................................................................................................... 109 LonTalk Communication Guide................................................................................................................................................. 112 LonTalk Points List ................................................................................................................................................................... 113 Web User Interface (Web UI) Installation and Operation ........................................................................................................ 116 Initial Setup............................................................................................................................................................................... 116 Basic Functions ........................................................................................................................................................................ 121 Advanced Functions ................................................................................................................................................................. 123 Sequence of Control................................................................................................................................................................... 124 Controls V2 IOM 2 May 2011 Part Number 474626
Safety WARNING: Improper installation, adjustment, service, maintenance, or alteration can cause property damage, personal injury, or loss of life. Installation, startup, and service must be performed by a qualified installer, service agency, or gas supplier. The customer must provide proper equipment and fully-trained installers to follow local safety requirements when receiving, installing, or servicing equipment. Consult all local building, electrical, occupational safety, and gas codes. Lock out all power supplies before servicing the unit to prevent accidental startup. All fan blades should be secured to prevent wind rotation. Remove any restrictive device before restoring power. The Clean Air Act of 1990 bans the intentional venting of refrigerant (CFC and HCFC) as of July 1, 1992. Approved methods of recovery, recycling, or reclaiming refrigerant must be followed. Fines and/or incarceration may be levied for non-compliance. Special Design Requests VPR, VPRE, VPRP and VPRX units are occasionally built with special features requested by the customer. This manual does not reflect any Special Design Requests and only covers standard options. Controls V2 IOM 3 May 2011 Part Number 474626
Page 1: Instruction, Operation, and Mainten
Page 5 and 6: I/O Configuration Universal Inputs
Page 7 and 8: 34 Point Module Supply Air Temperat
Page 9 and 10: Pressure Sensor Circuit B (Universa
Page 11 and 12: Analog Outputs 34 Point Module Modu
Page 13 and 14: Basic Functions Menu Commands The b
Page 15 and 16: Scheduling Adjustment IMPORTANT Int
Page 17 and 18: Advance Adjustment IP Address Adjus
Page 19 and 20: Op Mode Displays the operating mode
Page 21 and 22: Status Supply Air Temp Measured by
Page 23 and 24: Dampers Outside Air Damper Position
Page 25 and 26: CW FRZ Protect Used to disable the
Page 27 and 28: Manual Override Output Control Used
Page 29 and 30: Modulating Heat Used to override th
Page 31 and 32: Temperature Setpoints Occupied Spac
Page 33 and 34: Leaving Coil Setpt Used during dehu
Page 35 and 36: Stndby Humid SP Displays and sets t
Page 37 and 38: CO2 Control CO2 Setpoint The setpoi
Page 39 and 40: Air Flow Measuring AFMS K Factor Th
Page 41 and 42: Night Purge Ena Select whether the
Page 43 and 44: BACnet IP Enable Comm The unit is s
Page 45 and 46: Universal Maintenance Tool (UMT) Se
Page 47 and 48: Basic Functions Unit Status Select
Page 49 and 50: Advanced Functions Station Copier F
Page 51 and 52: Copying a Station from the Controll
Page 53 and 54:
File Transfer Client Use the file t
Page 55 and 56:
Supply Air Temperature Low Alarm Di
Page 57 and 58:
J Should only be changed under the
Page 59 and 60:
Cooling Lockout Setpoint The OAT th
Page 61 and 62:
air temperature in cooling mode and
Page 63 and 64:
Damper Setup 100% OA Damper Positio
Page 65 and 66:
Outside Dewpoint Setpoint Combined
Page 67 and 68:
Economizer PID Setpoint The offset
Page 69 and 70:
Heat Pump Setpoints Air Cooled Heat
Page 71 and 72:
Pressure Emergency Time The amount
Page 73 and 74:
Heat Pump Setup Head Pressure AO Di
Page 75 and 76:
Heat Wheel Cycle Delay Time The min
Page 77 and 78:
Minimum Heat Wheel Speed Displays a
Page 79 and 80:
Overheat Offset Space Temp Defines
Page 81 and 82:
Heat Enable Command, Modulating Hea
Page 83 and 84:
Hot Gas Reheat Hot Gas Reheat Enabl
Page 85 and 86:
Manual Overrides Output Control Use
Page 87 and 88:
Modulating Heat Percentage Used to
Page 89 and 90:
Sensors AFMS Sensor Measured by the
Page 91 and 92:
Raw AFMS Input Measured with a pres
Page 93 and 94:
Setpoints and Schedules Cool Down E
Page 95 and 96:
Optimized Start This point will be
Page 97 and 98:
Standby Occupied Standby Cooling Se
Page 99 and 100:
Space Static PID Integral Fan Shoul
Page 101 and 102:
Supply Fan Start VFD Speed Displays
Page 103 and 104:
4. When all changes are complete, s
Page 105 and 106:
Analog Values (continued) Instance
Page 107 and 108:
BACnet MSTP Communication Guide The
Page 109 and 110:
BACnet MSTP Points List Analog Valu
Page 111 and 112:
Binary Values Instance Object Type
Page 113 and 114:
LonTalk Points List Inputs Name NvI
Page 115 and 116:
Name NvIndex Direction SnvtType Des
Page 117 and 118:
5. Right-click on the identified Lo
Page 119 and 120:
Login Instructions To access the JE
Page 121 and 122:
Basic Functions Setpoint Adjustment
Page 123 and 124:
Advanced Functions TCP/IP Configura
Page 125 and 126:
3.2. Internal time clock in micropr
Page 127 and 128:
2.5. Energy Recovery (Plate) 1. Upo
Page 129 and 130:
dehumidification possible, but allo
Page 131 and 132:
3.3. Occupied mode disabled. 3.4. E
Page 133 and 134:
7. ECONOMIZER 7.1. Economizer mode
Page 135:
Valent® is a business of Unison Co
show all

Valent_IOM_Controls - RJI-Sales.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?