Valent_IOM_Controls - RJI-Sales.com

More documents

Recommendations

Info

Cooling Cooling SP Displays the current cooling setpoint that the unit will control the supply air temperature to when in cooling mode. View Only Compressor 1 Command Represents the commanded state of Compressor 1, Digital Output 2 of the controller. View Only Compressor 2 Command Represents the commanded state of Compressor 2, Digital Output 3 of the controller. View Only Compressor 3 Command Represents the commanded state of Compressor 3, Digital Output 4 of the controller. View Only Compressor 4 Command Represents the commanded state of Compressor 4, Digital Output 5 of the controller. View Only H/L PC -A Represents the status of Universal Input 9. The high pressure cutout and low pressure cutout for circuit A, are wired in series. When tripped, the high pressure cutout requires manual reset, press the red button on the switch to reset. The low pressure cutout is automatically reset when the pressure is above the mechanical limit of the switch. The pressure cutout switches are located in the compressor section of the unit. View Only Range: Normal, Alarm H/L PC -B Represents the status of Universal Input 10. The high pressure cutout and low pressure cutout for circuit B, are wired in series. When tripped, the high pressure cutout requires manual reset, press the red button on the switch to reset. The low pressure cutout is automatically reset when the pressure is above the mechanical limit of the switch. The pressure cutout switches are located in the compressor section of the unit. View Only Range: Normal, Alarm Reheat Pct The capacity (in percentage) being delivered by the hot gas reheat valves and coil if installed. Hot gas reheat is controlled by dehumidification logic and in cooling mode to maintain the supply air temperature at setpoint. View Only Reheat Ena Displays the status of the hot gas reheat loop enable. True when compressor 1 is enabled, not in shutdown, and unit is not in heating mode: Occupied dehumidification operation or Unoccupied dehumidification operation or Unit is cooling and supply temperature is below supply air setpoint. View Only Digital Pct The output in percentage of analog output 6 controlling the loaded and unloaded percentage of the digital scroll compressor. View Only Digital Scroll Priority This point allows the selection between temperature and humidity priority digital scroll operation during dehumidification. 13. Temperature 14. Humidity Editable Default: Temperature CWVLV Action Used to change the operation of the modulating cooling output that controls the chilled water valve (if applicable). In Direct Action the output delivers 0VDC at 0% and 10VDC at 100% cooling capacity. In Reverse Action the output delivers 10VDC at 0% and 0VDC at 100% cooling capacity. Editable Range: Direct Action, Reverse Action Default: Direct Action Chilled Wtr Vlv Pct Represents signal controlling the chilled water valve on analog output 6. View Only CW Coil LL Stpt Displays and edits the coil temperature that when below will shut the unit down to protect the chilled water coil. Editable Range: -20-60°F Default: 36°F Controls V2 IOM 24 May 2011 Part Number 474626
CW FRZ Protect Used to disable the chilled water coil freeze protection. Should only be disabled if the chilled water coil is adequately protected from freezing. 15. Enabled 16. Disabled Editable Default: Enabled Amb Clg LockedOn Displays the status of the ambient cooling lock on. The units first stage cooling source is locked on once the outside air temperature gets above the cooling lockin setpoint. View Only Crnt Lockon Tmp Displays the outside air temperature that when reached will lock the units first stage of cooling on. View Only Controls V2 IOM 25 May 2011 Part Number 474626
Page 1 and 2: Instruction, Operation, and Mainten
Page 3 and 4: Safety WARNING: Improper installati
Page 5 and 6: I/O Configuration Universal Inputs
Page 7 and 8: 34 Point Module Supply Air Temperat
Page 9 and 10: Pressure Sensor Circuit B (Universa
Page 11 and 12: Analog Outputs 34 Point Module Modu
Page 13 and 14: Basic Functions Menu Commands The b
Page 15 and 16: Scheduling Adjustment IMPORTANT Int
Page 17 and 18: Advance Adjustment IP Address Adjus
Page 19 and 20: Op Mode Displays the operating mode
Page 21 and 22: Status Supply Air Temp Measured by
Page 23: Dampers Outside Air Damper Position
Page 27 and 28: Manual Override Output Control Used
Page 29 and 30: Modulating Heat Used to override th
Page 31 and 32: Temperature Setpoints Occupied Spac
Page 33 and 34: Leaving Coil Setpt Used during dehu
Page 35 and 36: Stndby Humid SP Displays and sets t
Page 37 and 38: CO2 Control CO2 Setpoint The setpoi
Page 39 and 40: Air Flow Measuring AFMS K Factor Th
Page 41 and 42: Night Purge Ena Select whether the
Page 43 and 44: BACnet IP Enable Comm The unit is s
Page 45 and 46: Universal Maintenance Tool (UMT) Se
Page 47 and 48: Basic Functions Unit Status Select
Page 49 and 50: Advanced Functions Station Copier F
Page 51 and 52: Copying a Station from the Controll
Page 53 and 54: File Transfer Client Use the file t
Page 55 and 56: Supply Air Temperature Low Alarm Di
Page 57 and 58: J Should only be changed under the
Page 59 and 60: Cooling Lockout Setpoint The OAT th
Page 61 and 62: air temperature in cooling mode and
Page 63 and 64: Damper Setup 100% OA Damper Positio
Page 65 and 66: Outside Dewpoint Setpoint Combined
Page 67 and 68: Economizer PID Setpoint The offset
Page 69 and 70: Heat Pump Setpoints Air Cooled Heat
Page 71 and 72: Pressure Emergency Time The amount
Page 73 and 74: Heat Pump Setup Head Pressure AO Di
Page 75 and 76:
Heat Wheel Cycle Delay Time The min
Page 77 and 78:
Minimum Heat Wheel Speed Displays a
Page 79 and 80:
Overheat Offset Space Temp Defines
Page 81 and 82:
Heat Enable Command, Modulating Hea
Page 83 and 84:
Hot Gas Reheat Hot Gas Reheat Enabl
Page 85 and 86:
Manual Overrides Output Control Use
Page 87 and 88:
Modulating Heat Percentage Used to
Page 89 and 90:
Sensors AFMS Sensor Measured by the
Page 91 and 92:
Raw AFMS Input Measured with a pres
Page 93 and 94:
Setpoints and Schedules Cool Down E
Page 95 and 96:
Optimized Start This point will be
Page 97 and 98:
Standby Occupied Standby Cooling Se
Page 99 and 100:
Space Static PID Integral Fan Shoul
Page 101 and 102:
Supply Fan Start VFD Speed Displays
Page 103 and 104:
4. When all changes are complete, s
Page 105 and 106:
Analog Values (continued) Instance
Page 107 and 108:
BACnet MSTP Communication Guide The
Page 109 and 110:
BACnet MSTP Points List Analog Valu
Page 111 and 112:
Binary Values Instance Object Type
Page 113 and 114:
LonTalk Points List Inputs Name NvI
Page 115 and 116:
Name NvIndex Direction SnvtType Des
Page 117 and 118:
5. Right-click on the identified Lo
Page 119 and 120:
Login Instructions To access the JE
Page 121 and 122:
Basic Functions Setpoint Adjustment
Page 123 and 124:
Advanced Functions TCP/IP Configura
Page 125 and 126:
3.2. Internal time clock in micropr
Page 127 and 128:
2.5. Energy Recovery (Plate) 1. Upo
Page 129 and 130:
dehumidification possible, but allo
Page 131 and 132:
3.3. Occupied mode disabled. 3.4. E
Page 133 and 134:
7. ECONOMIZER 7.1. Economizer mode
Page 135:
Valent® is a business of Unison Co
show all

Valent_IOM_Controls - RJI-Sales.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?