Valent_IOM_Controls - RJI-Sales.com

More documents

Recommendations

Info

Leaving Coil LL Setpt Compressors will start to stage off if the coil temperature drops below this temperature in cooling mode. Editable Range: 30-50°F Default: 42°F Optimized Start This point will be set to true automatically when the optimized start stop enable is set to OSS Enable. This point allows users to select whether the unit will allow optimized start functionality. Optimized start will optimally calculate the start time based on historical data including: space temperature, space setpoint, outside air temperature. 45. true 46. false (default) Editable Optimized Stop This point will be set to true automatically when the optimized start stop enable is set to OSS Enable. This point allows users to select whether the unit will allow optimized stop functionality. Optimized stop will optimally calculate the stop time based on historical data including: space temperature, space setpoint, outside air temperature. 47. true 48. false (default) Editable Optimized SS Ena Allows user to select whether the unit will allow optimized start stop functionality. Optimized start stop will optimally calculate the start and stop time based on historical data including: space temperature, space setpoint, outside air temperature. 49. Enabled 50. Disabled (default) Editable Alarm 1. Critical Alarms Only Only alarms that shut down the unit will trigger the alarm output. • Supply Air Temperature High Alarm • Supply Air Temperature Low Alarm • Supply Air Temperature Failed Alarm • Unit Shutdown Input • Duct Static High Limit • Supply Fan Status Alarm 2. Moderate Alarms All of the alarms above plus these additional alarms will trigger the alarm output. • High/Low Press Cutout -A • High/Low Press Cutout -B • HP Circuit A Press Cutout • HP Circuit A Press Cutout • Exhaust Fan Status Alarm 3. All Alarms All of the units alarms will trigger the alarm output. • Rotation Sensor • Filter Alert Max Exh VFD Spd Displays and edits the maximum speed for the exhaust fan. Depending on the exhaust fan sequence, the exhaust fan will track the supply fan, the outside air damper, or to maintain a space static. Regardless of the sequence the exhaust fan VFD will never be controlled to a speed of greater than this percentage. Range: 50-110% Default: 50% Controls V2 IOM 42 May 2011 Part Number 474626
BACnet IP Enable Comm The unit is sent out with the BACnet comm. disabled, and will need to be set to enabled in order for the controller to start communicating via BACnet. Once changed to Enabled and all other BACnet setting have been changed to their desired values, the controller will need to be rebooted for these settings to come into effect. 51. Disabled (default) 52. Enabled Editable Object ID A BACnet method to identify a particular object within a device, using a combination of its object type and an instance number (unique for that type, within that device). In the case of the single Device Object (type) per BACnet device, it must have a unique instance number across the BACnet internetwork on which it is installed. Editable Range: 0-4,194,302 Default: 11 Network Number Displays and edits the network number that the controller is currently set up on. Editable Range: 0-65,534 Default: 1 BACnet MSTP Enable Comm The unit is sent out with the BACnet comm. disabled, and will need to be set to enabled in order for the controller to start communicating via BACnet. Once changed to Enabled and all other BACnet setting have been changed to their desired values, the controller will need to be rebooted for these settings to come into effect. 53. Disabled (default) 54. Enabled Editable Object ID A BACnet method to identify a particular object within a device, using a combination of its object type and an instance number (unique for that type, within that device). In the case of the single Device Object (type) per BACnet device, it must have a unique instance number across the BACnet internetwork on which it is installed. Editable Range: 0-4,194,302 Default: 11 Network Number Displays and edits the network number that the controller is currently set up on. Editable Range: 0-65,534 Default: 1 MSTP Address Set the Mstp Address to a unique BACnet MAC address on that MSTP trunk, in decimal, with valid range from 0 (default) to 127. Each BACnet device on the MS/TP network segment must have a unique MAC address. Editable Range: 0-127 Default: 1 Baud Rate The controller supports all MSTP baud rates, from 9600 to 76,800 kbps Editable Range: 9600 to 76,800 kbps Default: 9600 Controls V2 IOM 43 May 2011 Part Number 474626
Page 1 and 2: Instruction, Operation, and Mainten
Page 3 and 4: Safety WARNING: Improper installati
Page 5 and 6: I/O Configuration Universal Inputs
Page 7 and 8: 34 Point Module Supply Air Temperat
Page 9 and 10: Pressure Sensor Circuit B (Universa
Page 11 and 12: Analog Outputs 34 Point Module Modu
Page 13 and 14: Basic Functions Menu Commands The b
Page 15 and 16: Scheduling Adjustment IMPORTANT Int
Page 17 and 18: Advance Adjustment IP Address Adjus
Page 19 and 20: Op Mode Displays the operating mode
Page 21 and 22: Status Supply Air Temp Measured by
Page 23 and 24: Dampers Outside Air Damper Position
Page 25 and 26: CW FRZ Protect Used to disable the
Page 27 and 28: Manual Override Output Control Used
Page 29 and 30: Modulating Heat Used to override th
Page 31 and 32: Temperature Setpoints Occupied Spac
Page 33 and 34: Leaving Coil Setpt Used during dehu
Page 35 and 36: Stndby Humid SP Displays and sets t
Page 37 and 38: CO2 Control CO2 Setpoint The setpoi
Page 39 and 40: Air Flow Measuring AFMS K Factor Th
Page 41: Night Purge Ena Select whether the
Page 45 and 46: Universal Maintenance Tool (UMT) Se
Page 47 and 48: Basic Functions Unit Status Select
Page 49 and 50: Advanced Functions Station Copier F
Page 51 and 52: Copying a Station from the Controll
Page 53 and 54: File Transfer Client Use the file t
Page 55 and 56: Supply Air Temperature Low Alarm Di
Page 57 and 58: J Should only be changed under the
Page 59 and 60: Cooling Lockout Setpoint The OAT th
Page 61 and 62: air temperature in cooling mode and
Page 63 and 64: Damper Setup 100% OA Damper Positio
Page 65 and 66: Outside Dewpoint Setpoint Combined
Page 67 and 68: Economizer PID Setpoint The offset
Page 69 and 70: Heat Pump Setpoints Air Cooled Heat
Page 71 and 72: Pressure Emergency Time The amount
Page 73 and 74: Heat Pump Setup Head Pressure AO Di
Page 75 and 76: Heat Wheel Cycle Delay Time The min
Page 77 and 78: Minimum Heat Wheel Speed Displays a
Page 79 and 80: Overheat Offset Space Temp Defines
Page 81 and 82: Heat Enable Command, Modulating Hea
Page 83 and 84: Hot Gas Reheat Hot Gas Reheat Enabl
Page 85 and 86: Manual Overrides Output Control Use
Page 87 and 88: Modulating Heat Percentage Used to
Page 89 and 90: Sensors AFMS Sensor Measured by the
Page 91 and 92: Raw AFMS Input Measured with a pres
Page 93 and 94:
Setpoints and Schedules Cool Down E
Page 95 and 96:
Optimized Start This point will be
Page 97 and 98:
Standby Occupied Standby Cooling Se
Page 99 and 100:
Space Static PID Integral Fan Shoul
Page 101 and 102:
Supply Fan Start VFD Speed Displays
Page 103 and 104:
4. When all changes are complete, s
Page 105 and 106:
Analog Values (continued) Instance
Page 107 and 108:
BACnet MSTP Communication Guide The
Page 109 and 110:
BACnet MSTP Points List Analog Valu
Page 111 and 112:
Binary Values Instance Object Type
Page 113 and 114:
LonTalk Points List Inputs Name NvI
Page 115 and 116:
Name NvIndex Direction SnvtType Des
Page 117 and 118:
5. Right-click on the identified Lo
Page 119 and 120:
Login Instructions To access the JE
Page 121 and 122:
Basic Functions Setpoint Adjustment
Page 123 and 124:
Advanced Functions TCP/IP Configura
Page 125 and 126:
3.2. Internal time clock in micropr
Page 127 and 128:
2.5. Energy Recovery (Plate) 1. Upo
Page 129 and 130:
dehumidification possible, but allo
Page 131 and 132:
3.3. Occupied mode disabled. 3.4. E
Page 133 and 134:
7. ECONOMIZER 7.1. Economizer mode
Page 135:
Valent® is a business of Unison Co
show all

Valent_IOM_Controls - RJI-Sales.com

Create successful ePaper yourself

Delete template?

Save as template?