Compact / CANopen /HMI Controller / XBT GC ... - Schneider Electric

More documents

Recommendations

Info

XBTZGCCAN CANopen master Node ID: 127 Note: If the XBTZGCCAN is installed at the beginning of the CANopen bus you have to install a terminal resistor (120 Ohm) between terminal 2 (CAN_L) and terminal 4 (CAN_H) TeSysU CANopen communication module LULC08 The communication module is connected to the CANopen fieldbus using cable. TeSysU CANopen communication module LULC08 The baudrate is set to 500 kbps. Optimized_CANopen_XBTGC/GT/GK Schneider Electric 40
The following address is used: Node ID: 5 Advantys OTB CANopen network interface module OTB1C0DM9LP The communication module is connected to the CANopen fieldbus. Advantys OTB OTB1C0DM9LP Node ID: 10 used baudrate is 500 kbps. 1. Network address (Node-ID x10) encoder wheel 2. Network address (Node-ID x1) encoder wheel 3. Transmission speed encoder wheel Optimized_CANopen_XBTGC/GT/GK Schneider Electric 41
Page 1 and 2: This document is based on European
Page 3 and 4: Important Information NOTICE Read t
Page 5 and 6: CAUTION EQUIPMENT OPERATION HAZARD
Page 7 and 8: Abbreviations Abbreviation AC CB CF
Page 9 and 10: Application Source Code Introductio
Page 11 and 12: System Introduction The system chap
Page 13 and 14: Components Hardware: Mains switch
Page 15 and 16: Installation Introduction This chap
Page 17 and 18: Field devices and motors of main ra
Page 19 and 20: Hardware General General descriptio
Page 21 and 22: Motor Circuit Breaker GV2L07 and GV
Page 23 and 24: Magelis HMI controller XBTGC2230T D
Page 25 and 26: Servo Drive Lexium 32A LXM32AD18M2
Page 27 and 28: Servo Drive Lexium 32A 1-phase LXM3
Page 29 and 30: Servo Drive Lexium 32A 1-phase LXM3
Page 31 and 32: Motor Starter TeSysU Power base LUB
Page 33 and 34: Advantys OTB expansion I/O modules
Page 35 and 36: Communication General The TVDA arch
Page 37 and 38: Lexium 32A Modbus connection Pin Si
Page 39: CANopen preassembled connection cab
Page 43 and 44: Course of Action Optimized_CANopen_
Page 45 and 46: Controller Introduction The Control
Page 47 and 48: 2 Select in the path: HMI Controlle
Page 49 and 50: 4 Select CANopen Optimized and pres
Page 51 and 52: Add CANopen Devices 1 Right click o
Page 53 and 54: TeSysU CANopen configuration 1 To c
Page 55 and 56: 2 In the Library Manager click on A
Page 57 and 58: 6 Type a name of the function or fu
Page 59 and 60: 15 The VAR_GLOBAL variables are loc
Page 61 and 62: 5 The right frame lists the selecte
Page 63 and 64: Save the Project 1 To save the proj
Page 65 and 66: 5 The actual state of the download
Page 67 and 68: 12 The results of the download to t
Page 69 and 70: 2 POU ATV312_1_Ctrl contains the co
Page 71 and 72: 5 POU TeSysU_1_Ctrl contains the co
Page 73 and 74: HMI Introduction This application u
Page 75 and 76: 3 In the Switch Settings dialog, se
Page 77 and 78: 4 The display shows the new numeric
Page 79 and 80: 8 In the OTB page the actual I/O st
Page 81 and 82: Altivar 312 Introduction Note The A
Page 83 and 84: Lexium 32A Introduction Note The LX
Page 85 and 86: 3 TeSysU CANopen communication modu
Page 87 and 88: 5 The image on the right shows the
Page 89 and 90: Appendix Detailed Component List Ha
Page 91 and 92:
Hardware-Components Pos. Qty. Descr
Page 93 and 94:
Component Features Components Compa
Page 95 and 96:
Altivar 312 variable speed drive Th
Page 97 and 98:
Advantys OTB distributed I/O OTB1CO
Page 99 and 100:
SoMachine OEM Machine Programming S
Page 101:
Contact Publisher Process & Machine
show all

Compact / CANopen /HMI Controller / XBT GC ... - Schneider Electric

Create successful ePaper yourself

Delete template?

Save as template?