Datalogic Heron Software Configuration Manual - The Barcode ...

More documents

Recommendations

Info

ADVANCED FORMATTING Exit and Save Configuration Ì$-Î 2 Code 2 code ID ÌEK1hÎ Read the code type from the Code Identifier Table beginning in Appendix B. code length ÌEL1jÎ Read a number in the range 01-99 from the Hex/Numeric Table. 3 Concatenation Result Code ID use code 1 ID ÌEN0kÎ use code 2 ID ÌEN1nÎ Since you can concatenate codes from different families, you must select the Code ID character of the resulting code. The Code ID character will be sent in the output message only if it is enabled according to the Code Identifier selection (Datalogic, AIM, or Custom). 4 Concatenation Timeout timeout ÌEJ3Î Read two numbers in the range 00 to 99 00= no timeout 01-99 = timeout from 1 to 99 seconds Define the timeout, which determines the valid waiting period between the two codes, in order to accept concatenation. If the timeout expires, the resulting action will be based on the following selection. 90
ADVANCED FORMATTING Exit and Save Configuration Ì$-Î 5 Transmission after Timeout no code transmitted after timeout ÌEM0iÎ only code 1 transmitted (if read) after timeout ÌEM1lÎ only code 2 transmitted (if read) after timeout ÌEM2oÎ either code 1 or code 2 transmitted after timeout ÌEM3rÎ 91
Page 1:
HAND-HELD DEVICES II Software Confi
Page 4 and 5:
DATALOGIC S.p.A. Via Candini 2 4001
Page 6 and 7:
Num Lock...........................
Page 8 and 9:
4.4.1 Header/Terminator Selection .
Page 10 and 11:
Sending Configuration Strings from
Page 12 and 13:
1 HHD II 1.1 STATUS INDICATORS Seve
Page 14 and 15:
2 HHD II If the Host does not suppl
Page 16 and 17:
2 HHD II USB INTERFACE USB-KBD Ì$+
Page 18 and 19:
2 HHD II 2.1.3 Wedge Interface Sele
Page 20 and 21:
2 HHD II WEDGE INTERFACE (CONTINUED
Page 22 and 23:
3 HHD II 3 CONFIGURATION Once your
Page 24 and 25:
Enter Configuration Exit and Save C
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
RS232 PARAMETERS BAUD RATE PARIT
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
PEN EMULATION OPERATING MODE MIN
Page 46 and 47:
Page 48 and 49:
Page 50 and 51: IBM 46XX IBM DATA FORMATTING 1. R
Page 52 and 53: DATA FORMAT NOT FOR PEN INTERFACES
Page 54 and 55: DATA FORMAT • AIM standard identi
Page 56 and 57: Enter Configuration Exit and Save C
Page 66 and 67: READING PARAMETERS HAND-HELD OPERA
Page 74 and 75: DECODING PARAMETERS INK SPREAD O
Page 78 and 79: CODE SELECTION EAN/UPC FAMILY 2/
Page 98 and 99: ADVANCED FORMATTING CONCATENATION
Page 102 and 103: ADVANCED FORMATTING ADVANCED FORMAT
Page 104 and 105: ADVANCED FORMATTING Exit and Save C
Page 118 and 119: 4 HHD II 4.1.2 ACK/NACK Protocol Th
Page 120 and 121: 4 HHD II 4.2.4 Output and Idle Leve
Page 122 and 123: 4 HHD II 4.4 DATA FORMAT 4.4.1 Head
Page 124 and 125: Enter Configuration Ì$+;Î Exit an
Page 126 and 127: 4 HHD II 4.6 READING PARAMETERS 4.6
Page 128 and 129: 4 HHD II 4.6.7 Aiming System This p
Page 130 and 131: 4 HHD II 4.9 CONFIGURATION COPY COM
Page 132 and 133: 4 HHD II 4.11 FIRMWARE UPGRADES Dev
Page 134 and 135: A HHD II SERIAL CONFIGURATION STRIN
Page 136 and 137: A HHD II RS232 DESCRIPTION STRING B
Page 138 and 139: A HHD II IBM 46xx DESCRIPTION STRIN
Page 140 and 141: A HHD II READING PARAMETERS DESCRIP
Page 142 and 143: A HHD II CODE SELECTION (continued)
Page 144 and 145: A HHD II CODE SELECTION (continued)
Page 146 and 147: B HHD II UPC A with 2 ADD ON ÌFGÎ
Page 148 and 149: B HHD II 138
Page 150 and 151:
HEX AND NUMERIC TABLE C HEX / NUMER
show all

Datalogic Heron Software Configuration Manual - The Barcode ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?