Datalogic Heron Software Configuration Manual - The Barcode ...

More documents

Recommendations

Info

2 HHD II 2.1.3 Wedge Interface Selection Read the restore default code, then read the interface selection code for your application: RESTORE DEFAULT Ì$+$*oÎ WEDGE INTERFACE IBM AT or PS/2 PCs Ì$+CP500$-aÎ IBM XT Ì$+CP503$-vÎ PC Notebook Ì$+CP505$-ÈÎ IBM SURE1 Ì$+CP506$-$Î IBM Terminal 3153 Ì$+CP504$-}Î 8
INITIAL SETUP 2 WEDGE INTERFACE (CONTINUED) IBM Terminals 31xx, 32xx, 34xx, 37xx: To select the interface for these IBM Terminals, read the correct KEY TRANSMISSION code. select the KEYBOARD TYPE if necessary (default = advanced keyboard). KEY TRANSMISSION MODE make-only keyboard Ì$+CP502$-oÎ make-break keyboard Ì$+CP501$-hÎ KEYBOARD TYPE advanced keyboard Ì$+FK1$-ÉÎ typewriter keyboard Ì$+FK0$-ÄÎ ALT MODE <strong>The</strong> following interface selection allows barcodes sent to the PC to be interpreted correctly independently from the Keyboard Nationality used. You do not need to make a Keyboard Nationality selection. (default = Num Lock Unchanged). Make sure the Num Lock key on your keyboard is ON. IBM AT - ALT mode Ì$+CP507$-+Î PC Notebook - ALT mode Ì$+CP508$-2Î 9
Page 1: HAND-HELD DEVICES II Software Confi
Page 4 and 5: DATALOGIC S.p.A. Via Candini 2 4001
Page 6 and 7: Num Lock...........................
Page 8 and 9: 4.4.1 Header/Terminator Selection .
Page 10 and 11: Sending Configuration Strings from
Page 12 and 13: 1 HHD II 1.1 STATUS INDICATORS Seve
Page 14 and 15: 2 HHD II If the Host does not suppl
Page 16 and 17: 2 HHD II USB INTERFACE USB-KBD Ì$+
Page 20 and 21: 2 HHD II WEDGE INTERFACE (CONTINUED
Page 22 and 23: 3 HHD II 3 CONFIGURATION Once your
Page 24 and 25: Enter Configuration Exit and Save C
Page 30 and 31: RS232 PARAMETERS BAUD RATE PARIT
Page 44 and 45: PEN EMULATION OPERATING MODE MIN
Page 50 and 51: IBM 46XX IBM DATA FORMATTING 1. R
Page 52 and 53: DATA FORMAT NOT FOR PEN INTERFACES
Page 54 and 55: DATA FORMAT • AIM standard identi
Page 66 and 67: READING PARAMETERS HAND-HELD OPERA
Page 68 and 69:
Enter Configuration Exit and Save C
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
DECODING PARAMETERS INK SPREAD O
Page 76 and 77:
Page 78 and 79:
CODE SELECTION EAN/UPC FAMILY 2/
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
ADVANCED FORMATTING CONCATENATION
Page 100 and 101:
ADVANCED FORMATTING Exit and Save C
Page 102 and 103:
ADVANCED FORMATTING ADVANCED FORMAT
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
4 HHD II 4.1.2 ACK/NACK Protocol Th
Page 120 and 121:
4 HHD II 4.2.4 Output and Idle Leve
Page 122 and 123:
4 HHD II 4.4 DATA FORMAT 4.4.1 Head
Page 124 and 125:
Enter Configuration Ì$+;Î Exit an
Page 126 and 127:
4 HHD II 4.6 READING PARAMETERS 4.6
Page 128 and 129:
4 HHD II 4.6.7 Aiming System This p
Page 130 and 131:
4 HHD II 4.9 CONFIGURATION COPY COM
Page 132 and 133:
4 HHD II 4.11 FIRMWARE UPGRADES Dev
Page 134 and 135:
A HHD II SERIAL CONFIGURATION STRIN
Page 136 and 137:
A HHD II RS232 DESCRIPTION STRING B
Page 138 and 139:
A HHD II IBM 46xx DESCRIPTION STRIN
Page 140 and 141:
A HHD II READING PARAMETERS DESCRIP
Page 142 and 143:
A HHD II CODE SELECTION (continued)
Page 144 and 145:
A HHD II CODE SELECTION (continued)
Page 146 and 147:
B HHD II UPC A with 2 ADD ON ÌFGÎ
Page 148 and 149:
B HHD II 138
Page 150 and 151:
HEX AND NUMERIC TABLE C HEX / NUMER
show all

Datalogic Heron Software Configuration Manual - The Barcode ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?