Datalogic Heron Software Configuration Manual - The Barcode ...

More documents

Recommendations

Info

A HHD II READING PARAMETERS DESCRIPTION STRING Hand-Held Operation software trigger BK0 hardware trigger BK1 automatic BK2 always on BK3 hardware trigger ready BK4 Stand Operation software trigger BU1 hardware trigger BU3 automatic BU0 always on BU2 Hardware Trigger Signal trigger active level BA0 trigger active pulse BA1 Trigger-off Timeout (s) BD00 - BD99 FLASH ON (100 ms) BB001 - BB099 FLASH OFF (100 ms) BB101 - BB199 Reads per Cycle one read BC0 multiple reads BC1 Safety Time (100 ms) BE00 - BE99 Beeper Intensity beeper off BG0 low intensity BG1 medium intensity BG2 high intensity BG3 Beeper Tone tone 1 BH0 tone 2 BH1 tone 3 BH2 tone 4 BH3 Beeper Type monotone BJ0 bitonal BJ1 Beeper Length long BI0 short BI1 Good Read Spot Duration disable BV0 short BV1 medium BV2 long BV3 Stand Recognition Beep disable Ba0 enable Ba1 Automatic Operation Aiming Light disable Bb0 enable Bb1 Aiming System disable BX0 300 ms BX1 500 ms BX2 1 sec BX3 130
HOST CONFIGURATION STRINGS A DECODING PARAMETERS DESCRIPTION STRING Ink-spread disable AX0 enable AX1 Overflow control disable AW1 enable AW0 Interdigit control disable AV0 enable AV1 Decoding Safety one read ED0 two reads ED1 three reads ED2 four reads ED3 PuzzleSolver TM disable AU0 enable AU1 CODE SELECTION DESCRIPTION STRING DISABLE ALL FAMILY CODES AZ0 EAN/UPC disable EAN/UPC family AA0 EAN 8/EAN 13/UPC A/UPC E without ADD ON AA1 with ADD ON AA5 with and without ADD ON AA8 EAN 8/EAN 13 without ADD ON AA3 with ADD ON 2 ONLY AAK with ADD ON 5 ONLY AAL with ADD ON 2 AND 5 AA6 UPC A/UPC E without ADD ON AA4 with ADD ON 2 ONLY AAM with ADD ON 5 ONLY AAN with ADD ON 2 AND 5 AA7 EAN 8 check digit transmission disable AAG0 enable AAG1 EAN 13 check digit transmission disable AAH0 enable AAH1 UPC A check digit transmission disable AAI0 enable AAI1 UPC E check digit transmission disable AAJ0 enable AAJ1 conversions UPC E to UPC A AAA UPC E to EAN 13 AAB UPC A to EAN 13 AAC EAN 8 to EAN 13 AAD 131
Page 1:
HAND-HELD DEVICES II Software Confi
Page 4 and 5:
DATALOGIC S.p.A. Via Candini 2 4001
Page 6 and 7:
Num Lock...........................
Page 8 and 9:
4.4.1 Header/Terminator Selection .
Page 10 and 11:
Sending Configuration Strings from
Page 12 and 13:
1 HHD II 1.1 STATUS INDICATORS Seve
Page 14 and 15:
2 HHD II If the Host does not suppl
Page 16 and 17:
2 HHD II USB INTERFACE USB-KBD Ì$+
Page 18 and 19:
2 HHD II 2.1.3 Wedge Interface Sele
Page 20 and 21:
2 HHD II WEDGE INTERFACE (CONTINUED
Page 22 and 23:
3 HHD II 3 CONFIGURATION Once your
Page 24 and 25:
Enter Configuration Exit and Save C
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
RS232 PARAMETERS BAUD RATE PARIT
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
PEN EMULATION OPERATING MODE MIN
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
IBM 46XX IBM DATA FORMATTING 1. R
Page 52 and 53:
DATA FORMAT NOT FOR PEN INTERFACES
Page 54 and 55:
DATA FORMAT • AIM standard identi
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
READING PARAMETERS HAND-HELD OPERA
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
DECODING PARAMETERS INK SPREAD O
Page 76 and 77:
Page 78 and 79:
CODE SELECTION EAN/UPC FAMILY 2/
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91: Enter Configuration Exit and Save C
Page 98 and 99: ADVANCED FORMATTING CONCATENATION
Page 100 and 101: ADVANCED FORMATTING Exit and Save C
Page 102 and 103: ADVANCED FORMATTING ADVANCED FORMAT
Page 118 and 119: 4 HHD II 4.1.2 ACK/NACK Protocol Th
Page 120 and 121: 4 HHD II 4.2.4 Output and Idle Leve
Page 122 and 123: 4 HHD II 4.4 DATA FORMAT 4.4.1 Head
Page 124 and 125: Enter Configuration Ì$+;Î Exit an
Page 126 and 127: 4 HHD II 4.6 READING PARAMETERS 4.6
Page 128 and 129: 4 HHD II 4.6.7 Aiming System This p
Page 130 and 131: 4 HHD II 4.9 CONFIGURATION COPY COM
Page 132 and 133: 4 HHD II 4.11 FIRMWARE UPGRADES Dev
Page 134 and 135: A HHD II SERIAL CONFIGURATION STRIN
Page 136 and 137: A HHD II RS232 DESCRIPTION STRING B
Page 138 and 139: A HHD II IBM 46xx DESCRIPTION STRIN
Page 142 and 143: A HHD II CODE SELECTION (continued)
Page 144 and 145: A HHD II CODE SELECTION (continued)
Page 146 and 147: B HHD II UPC A with 2 ADD ON ÌFGÎ
Page 148 and 149: B HHD II 138
Page 150 and 151: HEX AND NUMERIC TABLE C HEX / NUMER
show all

Datalogic Heron Software Configuration Manual - The Barcode ...

Create successful ePaper yourself

Delete template?

Save as template?