Datalogic Heron Software Configuration Manual - The Barcode ...

More documents

Recommendations

Info

Enter Configuration Exit and Save Configuration Ì$+;Î READING PARAMETERS Ì$-Î SAFETY TIME safety time ÌBE&Î Limits same code consecutive reading. Read 2 numbers in the range 00-99: 00 = no same code consecutive reading until reader is removed (no decoding) for at least 400 ms. 01-99 = timeout from .1 to 9.9 seconds before a consecutive read on same code. safety time = 0.5 sec See par. 4.6.5 for details. BEEPER INTENSITY beeper off * ÌBG0ZÎ low intensity ÌBG1]Î medium intensity ÌBG2`Î high intensity ÌBG3cÎ * This sets the beeper OFF for data entry, while for all other beeper signals it has the meaning “very low intensity”. The Beeper Intensity parameter is effective for all operating conditions described in par. 1.1. 60
Enter Configuration Exit and Save Configuration Ì$+;Î READING PARAMETERS Ì$-Î BEEPER TONE tone 1 ÌBH0\Î tone 3 ÌBH2bÎ tone 2 ÌBH1_Î tone 4 ÌBH3eÎ BEEPER TYPE monotone ÌBJ0`Î bitonal ÌBJ1cÎ BEEPER LENGTH long ÌBI0^Î short ÌBI1aÎ 61
Page 1:
HAND-HELD DEVICES II Software Confi
Page 4 and 5:
DATALOGIC S.p.A. Via Candini 2 4001
Page 6 and 7:
Num Lock...........................
Page 8 and 9:
4.4.1 Header/Terminator Selection .
Page 10 and 11:
Sending Configuration Strings from
Page 12 and 13:
1 HHD II 1.1 STATUS INDICATORS Seve
Page 14 and 15:
2 HHD II If the Host does not suppl
Page 16 and 17:
2 HHD II USB INTERFACE USB-KBD Ì$+
Page 18 and 19:
2 HHD II 2.1.3 Wedge Interface Sele
Page 20 and 21: 2 HHD II WEDGE INTERFACE (CONTINUED
Page 22 and 23: 3 HHD II 3 CONFIGURATION Once your
Page 24 and 25: Enter Configuration Exit and Save C
Page 30 and 31: RS232 PARAMETERS BAUD RATE PARIT
Page 44 and 45: PEN EMULATION OPERATING MODE MIN
Page 50 and 51: IBM 46XX IBM DATA FORMATTING 1. R
Page 52 and 53: DATA FORMAT NOT FOR PEN INTERFACES
Page 54 and 55: DATA FORMAT • AIM standard identi
Page 66 and 67: READING PARAMETERS HAND-HELD OPERA
Page 74 and 75: DECODING PARAMETERS INK SPREAD O
Page 78 and 79: CODE SELECTION EAN/UPC FAMILY 2/
Page 98 and 99: ADVANCED FORMATTING CONCATENATION
Page 100 and 101: ADVANCED FORMATTING Exit and Save C
Page 102 and 103: ADVANCED FORMATTING ADVANCED FORMAT
Page 118 and 119: 4 HHD II 4.1.2 ACK/NACK Protocol Th
Page 120 and 121:
4 HHD II 4.2.4 Output and Idle Leve
Page 122 and 123:
4 HHD II 4.4 DATA FORMAT 4.4.1 Head
Page 124 and 125:
Enter Configuration Ì$+;Î Exit an
Page 126 and 127:
4 HHD II 4.6 READING PARAMETERS 4.6
Page 128 and 129:
4 HHD II 4.6.7 Aiming System This p
Page 130 and 131:
4 HHD II 4.9 CONFIGURATION COPY COM
Page 132 and 133:
4 HHD II 4.11 FIRMWARE UPGRADES Dev
Page 134 and 135:
A HHD II SERIAL CONFIGURATION STRIN
Page 136 and 137:
A HHD II RS232 DESCRIPTION STRING B
Page 138 and 139:
A HHD II IBM 46xx DESCRIPTION STRIN
Page 140 and 141:
A HHD II READING PARAMETERS DESCRIP
Page 142 and 143:
A HHD II CODE SELECTION (continued)
Page 144 and 145:
A HHD II CODE SELECTION (continued)
Page 146 and 147:
B HHD II UPC A with 2 ADD ON ÌFGÎ
Page 148 and 149:
B HHD II 138
Page 150 and 151:
HEX AND NUMERIC TABLE C HEX / NUMER
show all

Datalogic Heron Software Configuration Manual - The Barcode ...

Create successful ePaper yourself

Delete template?

Save as template?