Datalogic Heron Software Configuration Manual - The Barcode ...

More documents

Recommendations

Info

1 HHD II 1.1 STATUS INDICATORS Several status indicators are available depending on the type of reader: LEDs, Beeper, and Good Read Spot (for CCD Long Range readers only). They signal several operating conditions which are described in the tables below. H = high tone L = low tone READER START-UP Beeper 1 L L L L H H H H long tones H L H L OFF Meaning Parameters loaded correctly Parameter loading error, reading or writing error in the non volatile memory Hardware error in EEPROM No beeper performed when illuminator line is kept high at power on. READER CONFIGURATION Beeper 1 H H H H L L L L L H H H H Meaning correct entry in Configuration mode good read of a command command read error exit from Configuration mode READER DATA ENTRY Beeper 1 LED Good Read Spot Meaning one beep 2 ON ON correct read of a code in normal mode OFF OFF ready to read a code 1 2 only the Beeper Intensity command can modify these signals. the data entry good read tone is user-configurable with all the Beeper commands in the Reading Parameters section. 2
INITIAL SETUP 2 2 INITIAL SETUP 2.1 INTERFACE SELECTION Follow the procedure to configure the interface required by your application • USB Interface • RS232 Interface • Wedge Interface • Pen Emulation Interface • IBM 46xx Interface 2.1.1 USB Interface Configuration The USB interface is compatible with: - Windows 98 (and later) - Mac OS 8.0 (and later) - IBM POS for Windows - 4690 Operating System The USB interface is compatible with: Windows 98 (and later) Mac OS 8.0 (and later) IBM POS for Windows 4690 Operating System START-UP As with all USB devices, upon connection, the Host performs several checks by communicating with the USB device. During this phase the LED on the device blinks and normal operations are suspended. Two basic conditions must be met before the USB device is ready to read codes, the correct USB driver must be loaded and sufficient power must be supplied to the reader. For all systems, the correct USB driver for the default USB-KBD interface is included in the Host Operating System and will either be loaded automatically or will be suggested by the O.S. and should therefore be selected from the dialog box (the first time only). If the Host supplies sufficient power to the reader, the start-up phase ends correctly, the LED stops blinking and the reader emits the beep OK signal. 3
Page 1: HAND-HELD DEVICES II Software Confi
Page 4 and 5: DATALOGIC S.p.A. Via Candini 2 4001
Page 6 and 7: Num Lock...........................
Page 8 and 9: 4.4.1 Header/Terminator Selection .
Page 10 and 11: Sending Configuration Strings from
Page 14 and 15: 2 HHD II If the Host does not suppl
Page 16 and 17: 2 HHD II USB INTERFACE USB-KBD Ì$+
Page 18 and 19: 2 HHD II 2.1.3 Wedge Interface Sele
Page 20 and 21: 2 HHD II WEDGE INTERFACE (CONTINUED
Page 22 and 23: 3 HHD II 3 CONFIGURATION Once your
Page 24 and 25: Enter Configuration Exit and Save C
Page 30 and 31: RS232 PARAMETERS BAUD RATE PARIT
Page 44 and 45: PEN EMULATION OPERATING MODE MIN
Page 50 and 51: IBM 46XX IBM DATA FORMATTING 1. R
Page 52 and 53: DATA FORMAT NOT FOR PEN INTERFACES
Page 54 and 55: DATA FORMAT • AIM standard identi
Page 62 and 63:
Enter Configuration Exit and Save C
Page 64 and 65:
Page 66 and 67:
READING PARAMETERS HAND-HELD OPERA
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
DECODING PARAMETERS INK SPREAD O
Page 76 and 77:
Page 78 and 79:
CODE SELECTION EAN/UPC FAMILY 2/
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
ADVANCED FORMATTING CONCATENATION
Page 100 and 101:
ADVANCED FORMATTING Exit and Save C
Page 102 and 103:
ADVANCED FORMATTING ADVANCED FORMAT
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
4 HHD II 4.1.2 ACK/NACK Protocol Th
Page 120 and 121:
4 HHD II 4.2.4 Output and Idle Leve
Page 122 and 123:
4 HHD II 4.4 DATA FORMAT 4.4.1 Head
Page 124 and 125:
Enter Configuration Ì$+;Î Exit an
Page 126 and 127:
4 HHD II 4.6 READING PARAMETERS 4.6
Page 128 and 129:
4 HHD II 4.6.7 Aiming System This p
Page 130 and 131:
4 HHD II 4.9 CONFIGURATION COPY COM
Page 132 and 133:
4 HHD II 4.11 FIRMWARE UPGRADES Dev
Page 134 and 135:
A HHD II SERIAL CONFIGURATION STRIN
Page 136 and 137:
A HHD II RS232 DESCRIPTION STRING B
Page 138 and 139:
A HHD II IBM 46xx DESCRIPTION STRIN
Page 140 and 141:
A HHD II READING PARAMETERS DESCRIP
Page 142 and 143:
A HHD II CODE SELECTION (continued)
Page 144 and 145:
A HHD II CODE SELECTION (continued)
Page 146 and 147:
B HHD II UPC A with 2 ADD ON ÌFGÎ
Page 148 and 149:
B HHD II 138
Page 150 and 151:
HEX AND NUMERIC TABLE C HEX / NUMER
show all

Datalogic Heron Software Configuration Manual - The Barcode ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?