Datalogic Heron Software Configuration Manual - The Barcode ...

More documents

Recommendations

Info

Enter Configuration Exit and Save Configuration Ì$+;Î ADVANCED FORMATTING Ì$-Î No Match Result clear data - no transmission ÌHO0pÎ transmit data using standard format ÌHO1sÎ This selection determines the action to be taken when codes read do not conform to the advanced format requisites (no match). • Codes not matching can be ignored, cleared from memory and not transmitted. • Codes not matching can be transmitted using the Standard formatting (Headers, Code Length, Code ID, Terminators). 106
REFERENCES 4 4 REFERENCES 4.1 USB-COM AND RS232 PARAMETERS 4.1.1 Handshaking Hardware handshaking: (RTS/CTS) The RTS line is activated by the decoder before transmitting a character. Transmission is possible only if the CTS line (controlled by the Host) is active. Signals at EIA levels RTS TX Transmitted data Transmitted data CTS Host busy RTS/CTS handshaking Software handshaking: (XON/XOFF) During transmission, if the Host sends the XOFF character (13 Hex), the decoder interrupts the transmission with a maximum delay of one character and only resumes when the XON character (11 Hex) is received. Transmitted data Transmitted data TX RX XOFF Host busy XON Host ready XON/XOFF handshaking 107
Page 1:
HAND-HELD DEVICES II Software Confi
Page 4 and 5:
DATALOGIC S.p.A. Via Candini 2 4001
Page 6 and 7:
Num Lock...........................
Page 8 and 9:
4.4.1 Header/Terminator Selection .
Page 10 and 11:
Sending Configuration Strings from
Page 12 and 13:
1 HHD II 1.1 STATUS INDICATORS Seve
Page 14 and 15:
2 HHD II If the Host does not suppl
Page 16 and 17:
2 HHD II USB INTERFACE USB-KBD Ì$+
Page 18 and 19:
2 HHD II 2.1.3 Wedge Interface Sele
Page 20 and 21:
2 HHD II WEDGE INTERFACE (CONTINUED
Page 22 and 23:
3 HHD II 3 CONFIGURATION Once your
Page 24 and 25:
Enter Configuration Exit and Save C
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
RS232 PARAMETERS BAUD RATE PARIT
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
PEN EMULATION OPERATING MODE MIN
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
IBM 46XX IBM DATA FORMATTING 1. R
Page 52 and 53:
DATA FORMAT NOT FOR PEN INTERFACES
Page 54 and 55:
DATA FORMAT • AIM standard identi
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67: READING PARAMETERS HAND-HELD OPERA
Page 68 and 69: Enter Configuration Exit and Save C
Page 74 and 75: DECODING PARAMETERS INK SPREAD O
Page 78 and 79: CODE SELECTION EAN/UPC FAMILY 2/
Page 98 and 99: ADVANCED FORMATTING CONCATENATION
Page 100 and 101: ADVANCED FORMATTING Exit and Save C
Page 102 and 103: ADVANCED FORMATTING ADVANCED FORMAT
Page 118 and 119: 4 HHD II 4.1.2 ACK/NACK Protocol Th
Page 120 and 121: 4 HHD II 4.2.4 Output and Idle Leve
Page 122 and 123: 4 HHD II 4.4 DATA FORMAT 4.4.1 Head
Page 124 and 125: Enter Configuration Ì$+;Î Exit an
Page 126 and 127: 4 HHD II 4.6 READING PARAMETERS 4.6
Page 128 and 129: 4 HHD II 4.6.7 Aiming System This p
Page 130 and 131: 4 HHD II 4.9 CONFIGURATION COPY COM
Page 132 and 133: 4 HHD II 4.11 FIRMWARE UPGRADES Dev
Page 134 and 135: A HHD II SERIAL CONFIGURATION STRIN
Page 136 and 137: A HHD II RS232 DESCRIPTION STRING B
Page 138 and 139: A HHD II IBM 46xx DESCRIPTION STRIN
Page 140 and 141: A HHD II READING PARAMETERS DESCRIP
Page 142 and 143: A HHD II CODE SELECTION (continued)
Page 144 and 145: A HHD II CODE SELECTION (continued)
Page 146 and 147: B HHD II UPC A with 2 ADD ON ÌFGÎ
Page 148 and 149: B HHD II 138
Page 150 and 151: HEX AND NUMERIC TABLE C HEX / NUMER
show all

Datalogic Heron Software Configuration Manual - The Barcode ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?