Datalogic Heron Software Configuration Manual - The Barcode ...

More documents

Recommendations

Info

4 HHD II 4.9 CONFIGURATION COPY COMMAND Procedure: Connect the master (correctly configured reader) and the slave (reader to be configured) together through two RS232 serial interface cables and external power supply. Accessory cables and power supply are available from your Datalogic distributor to provide this connection. RS232 Cables: CAB363 & CAB364 or CAB320 & CAB328 Power Supply: PG5 Using the slave device, read the Restore Default barcode and then the RS232 interface barcode from par. 2.1.2 of this manual or from the Quick Reference Manual. With the master device, read the Configuration Copy barcode below. Copy Configuration Ì$+ZZ0$-*Î $+ZZ0$- The configuration will be copied from the master to the slave device. The slave device signals the end of the procedure with a series of beeps. Note: The master device can be configured for any interface. 120
REFERENCES 4 4.10 DEFAULT PARAMETERS FOR POS SYSTEMS The default values for the RS232 and Data Format parameters for POS systems are listed in the following table: NIXDORF Mode A FUJITSU ICL Mode RS232 Group Baud Rate 9600 9600 9600 Parity Odd None Even Data Bits 8 8 8 Stop Bits 1 1 1 Handshaking Hardware (RTS/CTS) None RTS always on ACK/NACK Protocol Disabled Disabled Disabled FIFO Enabled Enabled Enabled Inter-Character Delay Disabled Disabled Disabled RX Timeout 9.9 sec 2 sec 9.9 sec Serial Trigger Lock Disabled Disabled Disabled Data Format Group Code Identifier Custom Custom Custom Header No Header No Header No Header Terminator CR CR CR Field Adjustment Disabled Disabled Disabled Code Length TX Not Transmitted Not Transmitted Not Transmitted Character Replacement Disabled Disabled Disabled The table below lists all the Code Identifiers available for POS systems: CODE NIXDORF Mode A FUJITSU ICL Mode UPC-A A0 A A UPC-E C0 E E EAN-8 B FF FF EAN-13 A F F Code 39 M None C [code length] Codabar N None N [code length] Code 128 K None L [code length] Interleaved 2 of 5 I None I [code length] Code 93 L None None Industrial 2 of 5 H None H [code length] UCC/EAN 128 P None L [code length] MSI/Plessey O None None Code 11 None None None 121
Page 1:
HAND-HELD DEVICES II Software Confi
Page 4 and 5:
DATALOGIC S.p.A. Via Candini 2 4001
Page 6 and 7:
Num Lock...........................
Page 8 and 9:
4.4.1 Header/Terminator Selection .
Page 10 and 11:
Sending Configuration Strings from
Page 12 and 13:
1 HHD II 1.1 STATUS INDICATORS Seve
Page 14 and 15:
2 HHD II If the Host does not suppl
Page 16 and 17:
2 HHD II USB INTERFACE USB-KBD Ì$+
Page 18 and 19:
2 HHD II 2.1.3 Wedge Interface Sele
Page 20 and 21:
2 HHD II WEDGE INTERFACE (CONTINUED
Page 22 and 23:
3 HHD II 3 CONFIGURATION Once your
Page 24 and 25:
Enter Configuration Exit and Save C
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
RS232 PARAMETERS BAUD RATE PARIT
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
PEN EMULATION OPERATING MODE MIN
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
IBM 46XX IBM DATA FORMATTING 1. R
Page 52 and 53:
DATA FORMAT NOT FOR PEN INTERFACES
Page 54 and 55:
DATA FORMAT • AIM standard identi
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
READING PARAMETERS HAND-HELD OPERA
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
DECODING PARAMETERS INK SPREAD O
Page 76 and 77:
Page 78 and 79:
CODE SELECTION EAN/UPC FAMILY 2/
Page 80 and 81: Enter Configuration Exit and Save C
Page 98 and 99: ADVANCED FORMATTING CONCATENATION
Page 100 and 101: ADVANCED FORMATTING Exit and Save C
Page 102 and 103: ADVANCED FORMATTING ADVANCED FORMAT
Page 118 and 119: 4 HHD II 4.1.2 ACK/NACK Protocol Th
Page 120 and 121: 4 HHD II 4.2.4 Output and Idle Leve
Page 122 and 123: 4 HHD II 4.4 DATA FORMAT 4.4.1 Head
Page 124 and 125: Enter Configuration Ì$+;Î Exit an
Page 126 and 127: 4 HHD II 4.6 READING PARAMETERS 4.6
Page 128 and 129: 4 HHD II 4.6.7 Aiming System This p
Page 132 and 133: 4 HHD II 4.11 FIRMWARE UPGRADES Dev
Page 134 and 135: A HHD II SERIAL CONFIGURATION STRIN
Page 136 and 137: A HHD II RS232 DESCRIPTION STRING B
Page 138 and 139: A HHD II IBM 46xx DESCRIPTION STRIN
Page 140 and 141: A HHD II READING PARAMETERS DESCRIP
Page 142 and 143: A HHD II CODE SELECTION (continued)
Page 144 and 145: A HHD II CODE SELECTION (continued)
Page 146 and 147: B HHD II UPC A with 2 ADD ON ÌFGÎ
Page 148 and 149: B HHD II 138
Page 150 and 151: HEX AND NUMERIC TABLE C HEX / NUMER
show all

Datalogic Heron Software Configuration Manual - The Barcode ...

Create successful ePaper yourself

Delete template?

Save as template?