Datalogic Heron Software Configuration Manual - The Barcode ...

More documents

Recommendations

Info

4.4.1 Header/Terminator Selection .................................................................... 112 4.4.2 Set Custom Extended Header/Terminator Keys ....................................... 113 4.5 Power Save............................................................................................... 115 4.5.1 Sleep State/USB Suspend........................................................................ 115 4.5.2 Enter Sleep Timeout ................................................................................. 115 4.5.3 Standby (only for CCD devices)................................................................ 115 4.6 Reading Parameters ................................................................................. 116 4.6.1 Hand-Held and Stand Operation............................................................... 116 4.6.2 Hardware Trigger Signal ........................................................................... 116 4.6.3 Trigger-Off Timeout................................................................................... 116 4.6.4 Reads per Cycle ....................................................................................... 116 4.6.5 Safety Time............................................................................................... 117 4.6.6 Automatic Operation Aiming Light............................................................. 117 4.6.7 Aiming System .......................................................................................... 118 4.7 Decoding Parameters ............................................................................... 118 4.7.1 Ink-Spread ................................................................................................ 118 4.7.2 Overflow Control ....................................................................................... 118 4.7.3 Interdigit Control........................................................................................ 118 4.8 Configuration Editing Commands ............................................................. 119 4.9 Configuration Copy Command.................................................................. 120 4.10 Default Parameters for POS Systems....................................................... 121 4.11 Firmware Upgrades .................................................................................. 122 A HOST CONFIGURATION STRINGS........................................................ 123 B CODE IDENTIFIER TABLE...................................................................... 135 C HEX AND NUMERIC TABLE ................................................................... 139 vi
CONFIGURATION METHODS Reading Configuration Barcodes If you wish to change the default settings, this manual provides complete configuration of your reader in an easy way: To configure your reader: 1) Open the folded page in Appendix C with the hex-numeric table and keep it open during the device configuration. 2) Read the Enter Configuration code ONCE, available at the top of each page of configuration. 3) Modify the desired parameters in one or more sections following the procedures given for each group. 4) Read the Exit and Save Configuration code ONCE, available at the top of each page of configuration. Reference notes describing the operation of the more complex parameters are given in chapter 4. Using DL Sm@rtSet DL Sm@rtSet is a Windows-based utility program providing a quick and user-friendly configuration method via the RS232 or USB-COM interfaces. It also allows upgrading the software of the connected device (see the DL Sm@rtSet User’s Manual for more details). Copy Command A previously configured reader (Master device), can be used to send its configuration directly to other readers of the same type. The particular procedure for each device is given in par. 4.9. vii
Page 1: HAND-HELD DEVICES II Software Confi
Page 4 and 5: DATALOGIC S.p.A. Via Candini 2 4001
Page 6 and 7: Num Lock...........................
Page 10 and 11: Sending Configuration Strings from
Page 12 and 13: 1 HHD II 1.1 STATUS INDICATORS Seve
Page 14 and 15: 2 HHD II If the Host does not suppl
Page 16 and 17: 2 HHD II USB INTERFACE USB-KBD Ì$+
Page 18 and 19: 2 HHD II 2.1.3 Wedge Interface Sele
Page 20 and 21: 2 HHD II WEDGE INTERFACE (CONTINUED
Page 22 and 23: 3 HHD II 3 CONFIGURATION Once your
Page 24 and 25: Enter Configuration Exit and Save C
Page 30 and 31: RS232 PARAMETERS BAUD RATE PARIT
Page 44 and 45: PEN EMULATION OPERATING MODE MIN
Page 50 and 51: IBM 46XX IBM DATA FORMATTING 1. R
Page 52 and 53: DATA FORMAT NOT FOR PEN INTERFACES
Page 54 and 55: DATA FORMAT • AIM standard identi
Page 58 and 59:
Enter Configuration Exit and Save C
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
READING PARAMETERS HAND-HELD OPERA
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
DECODING PARAMETERS INK SPREAD O
Page 76 and 77:
Page 78 and 79:
CODE SELECTION EAN/UPC FAMILY 2/
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
ADVANCED FORMATTING CONCATENATION
Page 100 and 101:
ADVANCED FORMATTING Exit and Save C
Page 102 and 103:
ADVANCED FORMATTING ADVANCED FORMAT
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
4 HHD II 4.1.2 ACK/NACK Protocol Th
Page 120 and 121:
4 HHD II 4.2.4 Output and Idle Leve
Page 122 and 123:
4 HHD II 4.4 DATA FORMAT 4.4.1 Head
Page 124 and 125:
Enter Configuration Ì$+;Î Exit an
Page 126 and 127:
4 HHD II 4.6 READING PARAMETERS 4.6
Page 128 and 129:
4 HHD II 4.6.7 Aiming System This p
Page 130 and 131:
4 HHD II 4.9 CONFIGURATION COPY COM
Page 132 and 133:
4 HHD II 4.11 FIRMWARE UPGRADES Dev
Page 134 and 135:
A HHD II SERIAL CONFIGURATION STRIN
Page 136 and 137:
A HHD II RS232 DESCRIPTION STRING B
Page 138 and 139:
A HHD II IBM 46xx DESCRIPTION STRIN
Page 140 and 141:
A HHD II READING PARAMETERS DESCRIP
Page 142 and 143:
A HHD II CODE SELECTION (continued)
Page 144 and 145:
A HHD II CODE SELECTION (continued)
Page 146 and 147:
B HHD II UPC A with 2 ADD ON ÌFGÎ
Page 148 and 149:
B HHD II 138
Page 150 and 151:
HEX AND NUMERIC TABLE C HEX / NUMER
show all

Datalogic Heron Software Configuration Manual - The Barcode ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?