Dinamap Pro Series Operation Manual - Ardus Medical, Inc.

More documents

Recommendations

Info

**a • ***e .:::::t:. a**me*oe • :gg::gp 53’ Rear Panel Connections 1 2 3 4 5 6 Battery compartment cover: Retains and protects internal battery Mains input: Used to connect to AC power supply External power socket: To be used with approved Critikon AC-DC power converter ONLY Inactive temperature cable storage: Inactive temperature probe cable attaches here (Models 200 and 400) Pole clamp: Used to clamp monitor to pole or stand Data interface connector: Host communications port (15 way D-type RS-232 serial port) for use only with equipment conforming to IEC 601-1, configured to comply with IEC 601-l-l 16
Getting Started I 15 16 I 17 18 Front Panel Controls and Indicators 7 Systolic pressure display: 3-digit red LED indicates measured systolic BP in mmHg 8 Active temperature probe holster: Temperature probe that is being used stored here (Models 200 and 400) 9 Diastolic pressure display: 3-digit red LED indicates measured diastolic BP in mmHg 10 Temperature probe cover storage: Box of probe covers stored here (Models 200 and 400) 11 Inactive temperature probe holster: Extra temperature probe can be stored here (Models 200 and 400) 12 Temperature display: 4-digit red LED indicates measured temperature (Models 200 and 400) 13 “C “F display: Indicates whether temperature is being displayed in degrees Celsius or Fahrenheit (Models 200 and 400)
Page 1 and 2: DlNAMAP@ PRO Series 100-400 Monitor
Page 3 and 4: Contents Introduction .............
Page 5 and 6: About the DINAMAP PRO Monitor DINAM
Page 7 and 8: Introduction Place the PRO Monitor
Page 9 and 10: Getting Started Unpacking the Monit
Page 11: Getting Started integrity can only
Page 15 and 16: Getting Started Switching the Monit
Page 17 and 18: Any time the paper is loaded, the p
Page 19 and 20: Using the Monitor Noninvasive Blood
Page 21 and 22: Using the Monitor the limb distal t
Page 23 and 24: Using the Monitor Procedures 1. Con
Page 25 and 26: Manual Mode Using the Monitor @ To
Page 27 and 28: Using the Monitor arterial pressure
Page 29 and 30: 4. Using the Monitor When the deter
Page 31 and 32: Using the Monitor If you select the
Page 33 and 34: 2 Using the Monitor Following the d
Page 35 and 36: • Excessive patient motion may be
Page 37 and 38: • Try to keep the patient still,
Page 39 and 40: Menu Tree ” ) 1 Stat 1 1 Main 1 S
Page 41 and 42: Rotor Rotating the rotor causes opt
Page 43 and 44: Notes • The Print button appears
Page 45 and 46: , / _> BPM SYS DIA MAP cl 15 cl 50
Page 47 and 48: TIME SYS DIA MAP BPM II:37 ___ ___
Page 49 and 50: SpO, Button (Models 300 and 400) Se
Page 51 and 52: 20 : 21 11 24-Aug-1999 .; 1 , Hour,
Page 53 and 54: Clinician Menu * ___*’ .>I i _I P
Page 55 and 56: Trend. Selection of this button dis
Page 57 and 58: Error and Warning Messages The erro
Page 59 and 60: Monitor mode Max: 42.2” C; 108.0
Page 61 and 62: Dimensions Weight, Including Batter
Page 63 and 64:
7. Appendix B Alarm Codes All alarm
Page 65 and 66:
Procedural and Error Alarm Codes Al
Page 67 and 68:
Procedural and Error Alarm Codes (c
Page 69 and 70:
‘al3h3 8ugeJadO 3!seg ayl s~oys a
Page 71 and 72:
-1 Appendix D Compatibility Table a
Page 73 and 74:
. Do not clean with isopropyl alcoh
Page 75 and 76:
Appendix F disposable sensors or th
Page 77:
Appendix F Batteries Caution: Do no
show all

Dinamap Pro Series Operation Manual - Ardus Medical, Inc.

Create successful ePaper yourself

Delete template?

Save as template?