Dinamap Pro Series Operation Manual - Ardus Medical, Inc.

More documents

Recommendations

Info

Product Compliance The DINAMAP@ PRO Monitor is classified in the following categories for compliance with IEC 601-l : • Class • Transportable I, internally powered • For continuous operation • Not suitable for use in the presence of flammable anesthetics • Not for use in the presence of an oxygen-enriched atmosphere (oxygen tent) • Type BF applied parts • IPXl, degree of protection against ingress of water • Sterilization/Disinfection, see Appendix F @ C QD us DINAMAP@ PRO MONITOR CLASSIFIED WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL AND OTHER SPECIFIED HAZARDS ONLY IN ACCORDANCE WITH CAN/CSA C22.2 NO. 601 .l . ALSO EVALUATED TO IEC-601-2-30. CC 0086 This product conforms with the essential requirements of the Medical Device Directive. Accessories without the CE mark are not guaranteed to meet the Essential Requirements of the Medical Device Directive. 10
Getting Started Unpacking the Monitor and Accessories Before attempting to use the PRO Monitor, take a few minutes to become acquainted with the Monitor and its accessories. Unpack the items carefully, and check them against the contents checklist enclosed in one of the accessory boxes. This is also a good time to check for any damage or shortage. If there is a problem or shortage, contact Critikon. It is recommended that all the packaging be retained, in case the Monitor must be returned for service in the future. Power Sources The PRO Monitor is designed to operate from either an internal lead-acid battery, AC mains or an IEC 601-l compliant DC power source (see Appendix A). For replacement rechargeable batteries, please refer to the Service section of this manual. The Monitor contains five fuses. Two AC line input fuses are mounted internally and are replaceable only by qualified service personnel. The remaining three fuses are autoresetable and mounted within the Monitor. These fuses protect the low voltage DC input, the battery, and the +5 V output on the host port connector. Powering the Monitor Before the PRO Monitor is used for the first time, the battery should be charged in the Monitor for at least 8 hours. Refer to the illustration of the rear panel connections. Looking at the rear of the PRO Monitor, remove the battery compartment cover. Insert the rechargeable battery into the compartment so that the battery terminals fit into the power clips at the bottom of the compartment. Then replace the cover. Insert the power cord plug into the mains external power socket (2) and plug into an AC outlet. Refer to the illustration of the front panel controls and indicators. With mains or externat DC power connected, the green external power indicator LED (14) will light to indicate that external power is being applied and that the battery is charging. If the battery is not inserted, the external
Page 1 and 2: DlNAMAP@ PRO Series 100-400 Monitor
Page 3 and 4: Contents Introduction .............
Page 5 and 6: About the DINAMAP PRO Monitor DINAM
Page 7: Introduction Place the PRO Monitor
Page 11 and 12: Getting Started integrity can only
Page 13 and 14: Getting Started I 15 16 I 17 18 Fro
Page 15 and 16: Getting Started Switching the Monit
Page 17 and 18: Any time the paper is loaded, the p
Page 19 and 20: Using the Monitor Noninvasive Blood
Page 21 and 22: Using the Monitor the limb distal t
Page 23 and 24: Using the Monitor Procedures 1. Con
Page 25 and 26: Manual Mode Using the Monitor @ To
Page 27 and 28: Using the Monitor arterial pressure
Page 29 and 30: 4. Using the Monitor When the deter
Page 31 and 32: Using the Monitor If you select the
Page 33 and 34: 2 Using the Monitor Following the d
Page 35 and 36: • Excessive patient motion may be
Page 37 and 38: • Try to keep the patient still,
Page 39 and 40: Menu Tree ” ) 1 Stat 1 1 Main 1 S
Page 41 and 42: Rotor Rotating the rotor causes opt
Page 43 and 44: Notes • The Print button appears
Page 45 and 46: , / _> BPM SYS DIA MAP cl 15 cl 50
Page 47 and 48: TIME SYS DIA MAP BPM II:37 ___ ___
Page 49 and 50: SpO, Button (Models 300 and 400) Se
Page 51 and 52: 20 : 21 11 24-Aug-1999 .; 1 , Hour,
Page 53 and 54: Clinician Menu * ___*’ .>I i _I P
Page 55 and 56: Trend. Selection of this button dis
Page 57 and 58: Error and Warning Messages The erro
Page 59 and 60:
Monitor mode Max: 42.2” C; 108.0
Page 61 and 62:
Dimensions Weight, Including Batter
Page 63 and 64:
7. Appendix B Alarm Codes All alarm
Page 65 and 66:
Procedural and Error Alarm Codes Al
Page 67 and 68:
Procedural and Error Alarm Codes (c
Page 69 and 70:
‘al3h3 8ugeJadO 3!seg ayl s~oys a
Page 71 and 72:
-1 Appendix D Compatibility Table a
Page 73 and 74:
. Do not clean with isopropyl alcoh
Page 75 and 76:
Appendix F disposable sensors or th
Page 77:
Appendix F Batteries Caution: Do no
show all

Dinamap Pro Series Operation Manual - Ardus Medical, Inc.

Create successful ePaper yourself

Delete template?

Save as template?