Dinamap Pro Series Operation Manual - Ardus Medical, Inc.

More documents

Recommendations

Info

3. 4. • Place the sensor so that the opposite each other. LEDs and the photodiode are Plug the SpOz sensor into the Sp02 sensor extension cable. Then plug the SpOZ sensor extension cable into the SpOz sensor connector (18). <strong>Pro</strong>ceed with monitoring. SpOz determinations run continuously and can run simultaneously with other measurements. . . , .; 38
• Excessive patient motion may be making SpOz function to find a pulse pattern. • The sensor may be damaged. • The patient’s perfusion may be too low to allow the function to measure saturation and pulse rate. SOLUTION: Check the patient. • If possible, keep the patient still; check whether the SpOz sensor is applied securely and properly, and replace it if necessary; move the sensor to a new site; or use a disposable adhesive sensor that may tolerate more motion. • Replace the sensor. PROBLEM: The SpO2 value or the pulse rate changes rapidly; the puise amplitude bar is erratic. CAUSE: . Excessive patient motion may be making it impossible for the SpOz function to find a pulse pattern. • An electrosurgical unit (ESU) may be interfering with performance. SOLUTION: Check the patient. Using the Monitor Troubleshooting This section discusses potential difficulties and suggestions for resolving them. If the difficulty persists, contact a qualified service person or your local Critikon representative. The service manual, which is for use by qualified service personnel provides additional troubleshooting information. PROBLEM: The pulse amplitude bar indicates a pulse, but no oxygen saturation or pulse rate values appear on the screen. CAUSE: it impossible for the SpOz • If possible, keep the patient still; check whether the sensor is applied securely and properly, and replace it if necessary; move the sensor to a new site; use a sensor that tolerates more motion. Y- ” i LI 39
Page 1 and 2: DlNAMAP@ PRO Series 100-400 Monitor
Page 3 and 4: Contents Introduction .............
Page 5 and 6: About the DINAMAP PRO Monitor DINAM
Page 7 and 8: Introduction Place the PRO Monitor
Page 9 and 10: Getting Started Unpacking the Monit
Page 11 and 12: Getting Started integrity can only
Page 13 and 14: Getting Started I 15 16 I 17 18 Fro
Page 15 and 16: Getting Started Switching the Monit
Page 17 and 18: Any time the paper is loaded, the p
Page 19 and 20: Using the Monitor Noninvasive Blood
Page 21 and 22: Using the Monitor the limb distal t
Page 23 and 24: Using the Monitor Procedures 1. Con
Page 25 and 26: Manual Mode Using the Monitor @ To
Page 27 and 28: Using the Monitor arterial pressure
Page 29 and 30: 4. Using the Monitor When the deter
Page 31 and 32: Using the Monitor If you select the
Page 33: 2 Using the Monitor Following the d
Page 37 and 38: • Try to keep the patient still,
Page 39 and 40: Menu Tree ” ) 1 Stat 1 1 Main 1 S
Page 41 and 42: Rotor Rotating the rotor causes opt
Page 43 and 44: Notes • The Print button appears
Page 45 and 46: , / _> BPM SYS DIA MAP cl 15 cl 50
Page 47 and 48: TIME SYS DIA MAP BPM II:37 ___ ___
Page 49 and 50: SpO, Button (Models 300 and 400) Se
Page 51 and 52: 20 : 21 11 24-Aug-1999 .; 1 , Hour,
Page 53 and 54: Clinician Menu * ___*’ .>I i _I P
Page 55 and 56: Trend. Selection of this button dis
Page 57 and 58: Error and Warning Messages The erro
Page 59 and 60: Monitor mode Max: 42.2” C; 108.0
Page 61 and 62: Dimensions Weight, Including Batter
Page 63 and 64: 7. Appendix B Alarm Codes All alarm
Page 65 and 66: Procedural and Error Alarm Codes Al
Page 67 and 68: Procedural and Error Alarm Codes (c
Page 69 and 70: ‘al3h3 8ugeJadO 3!seg ayl s~oys a
Page 71 and 72: -1 Appendix D Compatibility Table a
Page 73 and 74: . Do not clean with isopropyl alcoh
Page 75 and 76: Appendix F disposable sensors or th
Page 77: Appendix F Batteries Caution: Do no

Dinamap Pro Series Operation Manual - Ardus Medical, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?