ADAM 4000 Series

More documents

Recommendations

Info

Data Formats and I/O Ranges B.3.2 Percent of Span The Percent of Span format is employed by setting bits 0 and 1 of the data format/slew rate/checksum parameter to 01. This format consists of a “+” or “-” sign, three decimal digits, a decimal point and two decimal digits. Data is presented as the value sent of the output signal relative to the span of the output (percent of span). The maximum resolution is 0.2% of span (5 µA for the 0 to 20 mA output range) and the desired output value is 10 mA the format of the Analog Data Out command is as follows: #01+050.00 (cr) indicating that the output is at 50% of span. The decimal point is fixed. B.3.3 Hexadecimal This format is selected by setting bits 0 and 1 of the data format/slew rate/ checksum parameter to 10. ASCII’s condensed hexadecimal representation of data allows and provides high resolution, quick communication and easy conversion to computercompatible integer format. The format consists of a 3-character hexadecimal string representing a 12-bit binary value. The resolution for the 0 to 20 mA output range equals .025% of span, which is 5 µA. The corresponding value for 000 is 0 mA; likewise, the value FFF corresponds to 20 mA. B-14 ADAM 4000 Series User's Manual
B.4 Analog Output Ranges Range Code (hex) Input Range Description 30 0to20mA 31 4to20mA 32 0to10V Data Formats Maximum Specitied Signal Minimum Specitied Signal Appendix B Output Resolution Engineering Unite 20.000 00.000 5 A % of FSR +100.00 +000.00 5 A Hexadecimal Binary FFF 000 5 A Engineering Unite 20.000 04.000 5 A % of FSR +100.00 +000.00 5 A Hexadecimal Binary FFF 000 5 A Engineering Unite 20.000 00.000 2.442 mA % of FSR +100.00 +000.00 2.442 mA Hexadecimal Binary FFF 000 2.442 mA Appendix B Data Formats and I/O Ranges B-15
Page 1:
ADAM 4000 Series Data Acquisition M
Page 4 and 5:
Table of Contents Chapter 1 Introdu
Page 6 and 7:
B.2 Analog Input Ranges ...........
Page 8 and 9:
Introduction 1.1 Overview The ADAM
Page 10 and 11:
Introduction The RS-485 network, to
Page 12 and 13:
Installation Guideline This chapter
Page 14 and 15:
Installation Guideline Assume that
Page 16 and 17:
Installation Guideline 2.2 Basic co
Page 18 and 19:
Installation Guideline To change th
Page 20 and 21:
Installation Guideline Changing Bau
Page 22 and 23:
Installation Guideline 2.5 Applicat
Page 24 and 25:
Installation Guideline Programming
Page 26 and 27:
Installation Guideline 2-16 ADAM 40
Page 28 and 29:
I/O Modules 3.1 ADAM-4011/4011D/401
Page 30 and 31:
I/O Modules Function Description fo
Page 32 and 33:
I/O Modules ADAM-4011D Figure 3-2 A
Page 34 and 35:
I/O Modules 3-8 ADAM 4000 Series Us
Page 36 and 37:
I/O Modules Figure 3-8 Digital Outp
Page 38 and 39:
I/O Modules ADAM-4015 6-channel RTD
Page 40 and 41:
I/O Modules Technical specification
Page 42 and 43:
I/O Modules Alarm signalling Strain
Page 44 and 45:
I/O Modules Application Wiring 3-18
Page 46 and 47:
I/O Modules 3.3 ADAM-4017/4017+/401
Page 48 and 49:
I/O Modules ADAM-4017 DATA ACQUISIT
Page 50 and 51:
I/O Modules Jumper setting 1. JP9 a
Page 52 and 53:
I/O Modules ADAM-4018M DATA ACQUISI
Page 54 and 55:
Page 56 and 57:
I/O Modules Application Wiring 11 1
Page 58 and 59:
I/O Modules 3.4 ADAM-4019 8-channel
Page 60 and 61:
Page 62 and 63:
I/O Modules ADAM-4021 3-36 ADAM 400
Page 64 and 65:
I/O Modules 3.6 ADAM-4050/4051/4052
Page 66 and 67:
I/O Modules ADAM-4051 Figure 3-32 A
Page 68 and 69:
Page 70 and 71:
I/O Modules Number of Output Channe
Page 72 and 73:
I/O Modules Figure 3-37 Digital Out
Page 74 and 75:
I/O Modules 3-48 ADAM 4000 Series U
Page 76 and 77:
I/O Modules 3.7 ADAM-4060/4068 Rela
Page 78 and 79:
I/O Modules Application Wiring The
Page 80 and 81:
I/O Modules 3.8 ADAM-4080/4080D Cou
Page 82 and 83:
Page 84 and 85:
I/O Modules Application Wiring Coun
Page 86 and 87:
Command Set 4.1 Introduction To avo
Page 88 and 89:
Command Set 4.3 I/O Module Commands
Page 90 and 91:
Command Set ADAM-4011D Command Tabl
Page 92 and 93:
Command Set ADAM-4012 Command Table
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Command Set Command Syntax Command
Page 100 and 101:
Command Set ADAM-4017+ Command Set
Page 102 and 103:
Command Set Input range and externa
Page 104 and 105:
Command Set ADAM-4018+ Command Set
Page 106 and 107:
Command Set Command Syntex Command
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Command Set ADAM-4055 Command Set T
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Command Set ADAM-4080D Command Tabl
Page 122 and 123:
Page 124 and 125:
Command Set 4-40 ADAM 4000 Series U
Page 126 and 127:
Command Set Command Syntax $AA6 Rea
Page 128 and 129:
4011, 4011D, 4012, 4013, 4015, 4016
Page 130 and 131:
4011, 4011D, 4012, 4013, 4015, 4016
Page 132 and 133:
4011, 4011D, 4012, 4013, 4015, 4016
Page 134 and 135:
4011, 4011D, 4012, 4013, 4015, 4016
Page 136 and 137:
4011, 4011D, 4012, 4013, 4015, 4016
Page 138 and 139:
4015, 4017, 4017+, 4018, 4018+, 401
Page 140 and 141:
4015, 4017, 4017+, 4018, 4018+, 401
Page 142 and 143:
4011, 4011D, 4012, 4013, 4016, 4017
Page 144 and 145:
4011, 4011D, 4012, 4013, 4015, 4016
Page 146 and 147:
4011D, 4015 $AAB Name Channel Diagn
Page 148 and 149:
4011, 4011D, 4018, 4018+, 4018M, 40
Page 150 and 151:
4015, 4019 $AA1Ci Name Single Chann
Page 152 and 153:
Command Set ADAM-4015 command codes
Page 154 and 155:
4015, 4019 $AA8Ci Name Read Single
Page 156 and 157:
4015, 4019 $AAY Name Read Watchdog
Page 158 and 159:
4015 $AAS1 Name Reload Default Cali
Page 160 and 161:
Command Set 4-76 ADAM 4000 Series U
Page 162 and 163:
Command Set 4014D $AA3 Name Read So
Page 164 and 165:
Command Set 4014D $AA5 Name Read Ta
Page 166 and 167:
Command Set 4014D $AA6(data_A)(data
Page 168 and 169:
Command Set 4014D $AA7(data_C)(data
Page 170 and 171:
Command Set 4014D $AAAV Name Enable
Page 172 and 173:
Command Set 4014D $AA9(data) Name S
Page 174 and 175:
Command Set 4018M @AACCCSDMTTTT Nam
Page 176 and 177:
Command Set 4018M @AAD Name Read Me
Page 178 and 179:
Command Set 4018M @AAT Name Read Me
Page 180 and 181:
Command Set 4018M @AAN Name Standar
Page 182 and 183:
Command Set 4018M @AARNNNN HHHH rep
Page 184 and 185:
Command Set 4018M @AAACSDHHHHTEIIII
Page 186 and 187:
Command Set 4018M 4-102 ADAM 4000 S
Page 188 and 189:
Command Set @AADI Name Read Digital
Page 190 and 191:
Command Set @AADO Name Set Digital
Page 192 and 193:
Command Set @AAEAT Name Enable Alar
Page 194 and 195:
Command Set @AAHI Name Set High Ala
Page 196 and 197:
Command Set @AADA Name Disable Alar
Page 198 and 199:
Command Set Name Read High Alarm Li
Page 200 and 201:
Command Set @AARE Name Read Event C
Page 202 and 203:
Command Set 4-118 ADAM 4000 Series
Page 204 and 205:
Command Set 4016 $AA6 Name Get Exci
Page 206 and 207:
Command Set 4016 $AAS Name Start-up
Page 208 and 209:
Command Set 4016 $AAE Name Trim Cal
Page 210 and 211:
Command Set 4016 $AAB Name Span Cal
Page 212 and 213:
Command Set 4021 %AANNTTCCFF Name C
Page 214 and 215:
Command Set 4021 %AANNTTCCFF Exampl
Page 216 and 217:
Command Set 4021 #AA Example comman
Page 218 and 219:
Command Set 4021 $AA3 Name Trim Cal
Page 220 and 221:
Command Set 4021 $AA0 Name 4 mA Cal
Page 222 and 223:
Command Set 4021 $AA2 Name Read Con
Page 224 and 225:
Command Set 4021 $AA8 Name Current
Page 226 and 227:
Command Set 4021 $AAF Name Read Fir
Page 228 and 229:
Command Set 4021 Spec : 1. 4 CH 12-
Page 230 and 231:
Command Set 4021 About System / CH
Page 232 and 233:
Command Set 4021 I2+ I2- V2 FGND V1
Page 234 and 235:
Command Set 4021 4-150 ADAM 4000 Se
Page 236 and 237:
Command Set 4050, 4052, 4053, 4060,
Page 238 and 239:
Command Set 4050, 4052, 4053, 4060,
Page 240 and 241:
Command Set 4050, 4052, 4053, 4050,
Page 242 and 243:
Command Set 4050, 4052, 4053, 4060,
Page 244 and 245:
Command Set 4050, 4052, 4053, 4060,
Page 246 and 247:
Command Set 4050, 4052, 4053, 4060,
Page 248 and 249:
Command Set 4050, 4052, 4053, 4060,
Page 250 and 251:
Command Set 4050, 4052, 4053, 4060,
Page 252 and 253:
Command Set 4080, 4080D %AANNTTCCFF
Page 254 and 255:
Command Set 4080, 4080D $AA2 Name C
Page 256 and 257:
Command Set 4080, 4080D $AAM Name R
Page 258 and 259:
Command Set 4080, 4080D $AAB Name R
Page 260 and 261:
Command Set 4080, 4080D $AA8V Name
Page 262 and 263:
Command Set 4080, 4080D $AA9(data)
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Command Set 4080, 4080D $AA4S Name
Page 276 and 277:
Command Set 4080, 4080D $AA0H(data)
Page 278 and 279:
Command Set 4080, 4080D $AA0L(data)
Page 280 and 281:
Command Set 4080, 4080D $AA1H(data)
Page 282 and 283:
Command Set 4080, 4080D $AA1L(data)
Page 284 and 285:
Command Set 4080, 4080D 4-200 ADAM
Page 286 and 287:
Command Set Command Syntax @AAEAT E
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Calibration Analog input/output mod
Page 306 and 307:
Calibration 6. Only for ADAM 4011,
Page 308 and 309:
Calibration Module Input Range Code
Page 310 and 311:
Calibration 5. Issue an Offset Cali
Page 312 and 313:
Calibration 4. Issue the Analog Dat
Page 314 and 315:
Calibration 4. Execute the Span Cal
Page 316 and 317: Technical specifications A.1 ADAM-4
Page 318 and 319: Technical specifications A-4 ADAM 4
Page 320 and 321: Technical specifications Table A-4
Page 334 and 335: Technical specifications A-20 ADAM
Page 336 and 337: Technical specifications A.10 ADAM-
Page 338 and 339: Technical specifications Table A-14
Page 352 and 353: Technical specifications A-38 ADAM
Page 354 and 355: Data Formats and I/O Ranges B.1 Ana
Page 356 and 357: Data Formats and I/O Ranges Example
Page 358 and 359: Data Formats and I/O Ranges and sym
Page 360 and 361: Data Formats and I/O Ranges B.2 Ana
Page 362 and 363: Data Formats and I/O Ranges Range C
Page 364 and 365: Data Formats and I/O Ranges Range C
Page 368 and 369: Data Formats and I/O Ranges B-16 AD
Page 370 and 371: Technical Diagrams C.1 ADAM Dimensi
Page 372 and 373: Technical Diagrams C-4 ADAM 4000 Se
Page 378 and 379: Utility Software Main menu The main
Page 380 and 381: Utility Software The Checksum and B
Page 382 and 383: Utility Software Terminal Emulation
Page 384 and 385: Utility Software Alarm setting This
Page 386 and 387: Utility Software D-10 ADAM 4000 Ser
Page 388 and 389: RS-485 Network ADAM modules are ful
Page 390 and 391: RS-485 Network Random This is a com
Page 392 and 393: RS-485 Network Example: Each input
Page 394 and 395: RS-485 Network E.3 RS-485 Data Flow
Page 396 and 397: How to use the Checksum feature F.1
Page 398: How to use the Checksum feature Tab
show all

ADAM 4000 Series

Create successful ePaper yourself

Delete template?

Save as template?