SAP2000 SAP2000 Web Tutorial 1

More documents

Recommendations

Info

43. In this table note the following: Figure D-9: Table For Capacity Spectrum • Step identifies the step number in the pushover curve. • Teff is the effective period at the associated step. • βeff is the effective damping at the associated step. • Sd(C) and Sa(C) define a point on the ADRS capacity curve for the associated step. • Sd(D) and Sa(D) define a point on the single demand spectrum (variable damping) curve for the associated step. • Alpha is the factor used in converting the base shear to spectral acceleration at the associated step. • PF*φ is the factor used in converting the displacement to spectral displacement at the associated step. • To print this table, click on the File menu at the top of the table and select either Print Tables, to print to a printer, or Print Tables To File..., to print the table to a file. 44. Click the “X” in the upper right-hand corner of the table to close it. 45. Select the Base Shear vs Control Displacement option in the Plot Type area. SAP2000 Web Tutorial 1 120
46. From the File menu at the top of the Pushover Curve dialog box select Display Tables. A table similar to that shown in Figure D-10 appears. 47. In this table note the following: Figure D-10: Table For Pushover Curve • Step identifies the step number in the pushover curve. • Displacement and Base Shear define a point on the pushover curve for the associated step. B C • A-B, B-IO, IO-LS, LS-CP, CP-C, C-D, D-E, >E all identify the total number of hinges within each of these ranges on their associated forcedisplacement curves. Force IO LS CP D E • TOTAL is the total number of pushover hinges in the structure. A Displacement • To print this table, click on the File menu at the top of the table and select either Print Tables, to print to a printer, or Print Tables To File..., to print the table to a file. 48. You can also print graphic plots of the pushover curve and/or capacity spectrum curve as follows: SAP2000 Web Tutorial 1 121
Page 1 and 2:
SAP2000 ® Integrated Finite Elemen
Page 3 and 4:
DISCLAIMER CONSIDERABLE TIME, EFFOR
Page 5 and 6:
A. Introduction This tutorial is qu
Page 7 and 8:
B. Description of Building Model Th
Page 9 and 10:
Roof Level Second Floor Level Figur
Page 11 and 12:
For this model, all mass is input a
Page 13 and 14:
ä Check the Restraints box if it i
Page 15 and 16:
12. Place the mouse pointer near th
Page 17 and 18:
18. Place the mouse pointer on the
Page 19 and 20:
37. Click on the points labeled “
Page 21 and 22:
If you started the model from scrat
Page 23 and 24:
Thus click the ten locations design
Page 25 and 26:
Highlight -12 in the Y Location lis
Page 27 and 28:
26. Click anywhere on the combined
Page 29 and 30:
Figure C-14: Model After Braces Hav
Page 31 and 32:
56. To finish defining the model ge
Page 33 and 34:
• Accept the rest of the default
Page 35 and 36:
16. Highlight CONC in the Materials
Page 37 and 38:
Note: Frame sections may be selecte
Page 39 and 40:
Step 6: Assigning Groups Groups can
Page 41 and 42:
13. Click the Set Intersecting Line
Page 43 and 44:
37. From the Assign menu choose Gro
Page 45 and 46:
Step 7: Assigning Frame Sections Re
Page 47 and 48:
18. In the Frame Sections area clic
Page 49 and 50:
47. In the Frame Sections area clic
Page 51 and 52:
Step 8: Assigning Shell Sections 1.
Page 53 and 54:
Figure C-16: Frame Element Local Ax
Page 55 and 56:
Step 10: Defining Static Load Cases
Page 57 and 58:
Step 11: Assigning Frame Static Loa
Page 59 and 60:
In the Uniform Load area, type 0. C
Page 61 and 62:
Click the OK button to apply the lo
Page 63 and 64:
52. Click the Restore Previous Sele
Page 65 and 66:
Step 12: Assigning Shell Static Loa
Page 67 and 68:
Step 13: Assigning Joint Static Loa
Page 69 and 70:
Select EQX from the Load Case Name
Page 71 and 72:
Step 14: Assigning Joint Masses We
Page 73 and 74: 22. Click the Set Elements button o
Page 75 and 76: Step 16: Static and Dynamic Analysi
Page 77 and 78: 5. Use the scroll bar to review the
Page 79 and 80: Step 18: Reviewing Deformed Shapes
Page 81 and 82: Step 19: Reviewing Forces and Stres
Page 83 and 84: 18. All of the load cases in the Se
Page 85 and 86: Step 20: Performing a Steel Design
Page 87 and 88: 11. From the Select menu select Sel
Page 89 and 90: 21. Now we will confirm the unbrace
Page 91 and 92: and # represents the hinge number.
Page 93 and 94: • In the Type area select the For
Page 95 and 96: • Type 1 in the Relative Distance
Page 97 and 98: 19. Click the Save Model button on
Page 99 and 100: Figure D-2: Frame Hinge Property Da
Page 101 and 102: 12. Click the Set Elements button o
Page 103 and 104: Figure D-3: Static Pushover Case Da
Page 105 and 106: the denominator is always the yield
Page 107 and 108: • In the Options area, select GRA
Page 109 and 110: Step 5: Running the Pushover Analys
Page 111 and 112: 9. Note that the title of the windo
Page 113 and 114: force is dropped, all elements unlo
Page 115 and 116: 3. Note that the title of the windo
Page 117 and 118: Figure D-7: Pushover Curve For Push
Page 119 and 120: Figure D-8: Capacity spectrum For P
Page 121 and 122: Note: In the ADRS format, lines of
Page 123: 32. Check the Show Constant Period
Page 127: E. Final Comments This tutorial, to
show all

SAP2000 SAP2000 Web Tutorial 1

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?