Electromagnetic Testing

More documents

Recommendations

Info

Test Coil Excitation The second consideration that was previously mentioned for determining the mode of operation of a test unit could be the way the probe is being energized. Figure 6.7 a typical surface riding pancake coil responses to an array of EDM notches on a calibration standard. Fig 6.8 shows a block diagram of a stepped, single frequency, phase amplitude instrument. The circuit in Fig 6.8 is capable of operating at any of the four frequency, if the four frequencies are spread over a wide range, several different test coils may be required to use the instrument over the entire range. Most modern single frequency instruments use this principle; however one variable frequency generator with a wide operating range usually replaced the four individual fixed generators. A typical frequency for such an instrument is in the low hertz range (50Hz to 100Hz) to several megahertz (8MHz to 10MHz). This large dynamic range gives these units a wide variety of possible applications. Charlie Chong/ Fion Zhang
Figure 6.7: Typical surface riding pancake coil response to an array of EDM notches on a calibration standard Charlie Chong/ Fion Zhang
Page 1 and 2:
Electromagnetic Testing Study Guide
Page 3 and 4:
E&P Applications Charlie Chong/ Fio
Page 5 and 6:
Charlie Chong/ Fion Zhang
Page 7 and 8:
乱七八糟 - 随看随记 C
Page 9 and 10:
Page 11 and 12:
Charlie Chong/ Fion Zhang http://ww
Page 13 and 14:
IVONA TTS Capable. Charlie Chong/ F
Page 15 and 16:
EDDY CURRENT an Overview Descriptio
Page 17 and 18:
Tangential Probe Charlie Chong/ Fio
Page 19 and 20:
Electromagnetic Testing Advantages
Page 21 and 22:
Factors Affecting Eddy Current Resp
Page 23 and 24:
from this it can be seen that depth
Page 25 and 26:
http://www.eng.morgan.edu/~hubert/I
Page 27 and 28:
Robotic Charlie Chong/ Fion Zhang
Page 29 and 30:
Measurement Techniques (EN!) a) Abs
Page 31 and 32:
Figure 1.1 Arago’s Experiment Cha
Page 33 and 34:
Oersted discovered the presence of
Page 35 and 36:
Figure 1.3: Induced current electro
Page 37 and 38:
Charlie Chong/ Fion Zhang http://en
Page 39 and 40:
Charlie Chong/ Fion Zhang http://en
Page 41 and 42:
The law of physics describing the p
Page 43 and 44:
Charlie Chong/ Fion Zhang http://hy
Page 45 and 46:
Magnetic Force The magnetic field B
Page 47 and 48:
Generation of Eddy Currents When a
Page 49 and 50:
Factors Affecting Inductance There
Page 51 and 52:
COIL LENGTH: All other factors bein
Page 53 and 54:
Coil Inductance L An approximation
Page 55 and 56:
Note the direction of the primary c
Page 57 and 58:
Generation of Eddy Current With a p
Page 59 and 60:
Charlie Chong/ Fion Zhang Permeabil
Page 61 and 62:
A Dual Variable inductors Figure 1:
Page 63 and 64:
Figure 3: Here is another inductor
Page 65 and 66:
Figure 4: The two inductors on this
Page 67 and 68:
Grundig radio satellit 750 ■ http
Page 69 and 70:
Figure 1.7: Phasor Diagram of Coil
Page 71 and 72:
Current Density The distribution of
Page 73 and 74:
Figure 1.8: Relative eddy current d
Page 75 and 76:
Relative Magnetic Permeability Perm
Page 77 and 78:
It should be observed at this point
Page 79 and 80:
δ = (π x 100 x 10 3 x 4 x π x 0.
Page 81 and 82:
Using 1.35 mm as depth x from surfa
Page 83 and 84:
Standard Depth for Different Conduc
Page 85 and 86:
Current (?) Lagging Voltage lagging
Page 87 and 88:
σº∙πμ■δ∝∞ωΩθ√ρβ
Page 89 and 90:
Figure 1.9 should be used as a rela
Page 91 and 92:
Figure 1.8: Relative eddy current d
Page 93 and 94:
Q.1.1 Generation of eddy currents d
Page 95 and 96:
Q.1.5 Eddy current generated a test
Page 97 and 98:
Q.1.9 Refer to Figure1.9 using exam
Page 99 and 100:
Chapter 2 The Coil Arrangements Cha
Page 101 and 102:
Probe coils and probe coil forms ca
Page 103 and 104:
Encircling Coils Encircling coil, o
Page 105 and 106:
Discussion Subject; Encircling Coil
Page 107 and 108:
Bobbin Coils Bobbin coil, inside di
Page 109 and 110:
Figure 2.5: Test coil configuration
Page 111 and 112:
Differential coils Differential coi
Page 113 and 114:
Figure 2.6: External reference diff
Page 115 and 116:
Figure 2.7: Hybrid coil (through tr
Page 117 and 118:
Additional Coil Characteristics Coi
Page 119 and 120:
Q.2.1 Differential coils are usuall
Page 121 and 122:
Q.2.6 An absolute coil measurement
Page 123 and 124:
The Answers Charlie Chong/ Fion Zha
Page 125 and 126:
As discussed earlier test coil desi
Page 127 and 128:
Demonstration model of a moving iro
Page 129 and 130:
Thus, the resistance of a 10 ft len
Page 131 and 132:
SPECIFIC RESISTANCE OR RESISTIVITY
Page 133 and 134:
Problem: What is the resistance of
Page 135 and 136:
The inductance of a multilayer air
Page 137 and 138:
Example: A coil whose dimensions ar
Page 139 and 140:
Example: Using the 32 μH coil calc
Page 141 and 142:
Impedance To explain the addition o
Page 143 and 144:
Maximum transfer of power is accomp
Page 145 and 146:
Rectangular Notation Because reacta
Page 147 and 148:
Vectors With Polar Notations. Stand
Page 149 and 150:
Rectangular Notation - Prefix “j
Page 151 and 152:
Imaginary Component In “rectangul
Page 153 and 154:
Imaginary Charlie Chong/ Fion Zhang
Page 155 and 156:
To convert from rectangular to pola
Page 157 and 158:
More Reading on Polar & Rectangular
Page 159 and 160:
Eddy current coils with included im
Page 161 and 162:
Permeability and Shielding Effects
Page 163 and 164:
Another technique of shielding uses
Page 165 and 166:
Saturation Approach Another coil de
Page 167 and 168:
Figure 3.5: Magnetic bias probe Cha
Page 169 and 170:
Materials must be chemically compat
Page 171 and 172:
Q.3.1 A coil's resistance is determ
Page 173 and 174:
Q.3.7 The Q or merit of a coil is d
Page 175 and 176:
Page 177 and 178:
Jackfruit Tree Charlie Chong/ Fion
Page 179 and 180:
Electrical Conductivity σ In elect
Page 181 and 182:
As previously discussed, conductivi
Page 183 and 184:
Figure 4.1; Conductivity curve Char
Page 185 and 186:
The coil's inductive reactance is r
Page 187 and 188:
Effects of Heat Treatment on Conduc
Page 189 and 190:
Permeability Permeability of any ma
Page 191 and 192:
When increases in the magnetizing f
Page 193 and 194:
Skin Effect Charlie Chong/ Fion Zha
Page 195 and 196:
Discussion Subject: Response to the
Page 197 and 198:
Lift Off Electromagnetic coupling b
Page 199 and 200:
Fill factor will always be a number
Page 201 and 202:
Figure 4.4: Fill factor ratios When
Page 203 and 204:
Example: Calculate the resultant lo
Page 205 and 206:
Figure 1.8 is again useful to illus
Page 207 and 208:
Signal-to-Noise Ratio Signal-to-noi
Page 209 and 210:
Page 211 and 212:
Q.4.4 A (?) prime factor affecting
Page 213 and 214:
Q.4.10 Temperature changes, vibrati
Page 215 and 216:
Test Frequencies It is the responsi
Page 217 and 218:
Single Frequency Systems Unfortunat
Page 219 and 220:
Eddy Current Density Since the sens
Page 221 and 222:
Applicable Scenario Eddy Current De
Page 223 and 224:
Standard Depth δ Formula The depth
Page 225 and 226:
Example 1: As an example of how thi
Page 227 and 228:
Frequency Selection - Ferromagnetic
Page 229 and 230:
A frequency can always selected to
Page 231 and 232:
Figure 5.1(a) shows the effect on p
Page 233 and 234:
Figure 5.1: Effects of frequency ch
Page 235 and 236:
Figure 5.2: Normalized impedance di
Page 237 and 238:
Figure 5.3: Impedance variations ca
Page 239 and 240:
Figure 5.4: Impedance variations ca
Page 241 and 242:
Multiparameter Techniques It become
Page 243 and 244:
Multiparameter Techniques - Multipl
Page 245 and 246:
First, a frequency is selected to g
Page 247 and 248:
More Reading on Characteristic Para
Page 249 and 250:
Figure 1: Eddy Current Testing Char
Page 251 and 252:
Figure 2: Types of Probes Charlie C
Page 253 and 254: Surface (Pancake) Probes Surface pr
Page 255 and 256: Encircling Probes Encircling probes
Page 257 and 258: Design of eddy current probes In mo
Page 259 and 260: In brief, probe design is usually d
Page 261 and 262: Analytical Approach (Pc & f g ) Ana
Page 263 and 264: RECENT TRENDS IN EDDY CURRENT PROBE
Page 265 and 266: Pressurized Heavy Water Reactors (P
Page 267 and 268: The Answers Charlie Chong/ Fion Zha
Page 269 and 270: Q.5.4 Calculate the limit frequency
Page 271 and 272: Q.5.7 Primary resistance is subtrac
Page 273 and 274: Q5.9 A 25% deep crack open to the n
Page 275 and 276: Chapter 6 Instrument Systems Charli
Page 277 and 278: Eddy Current Instrumentation Most o
Page 279 and 280: Figure 6.1: Internal functions of t
Page 281 and 282: Chernobyl Nuclear Power Plant Charl
Page 283 and 284: Figure 6.2: Four types of simple ed
Page 285 and 286: Figure 6.2(b) shows an impedance br
Page 287 and 288: Figure 6.2(d) illustrates a balanci
Page 289 and 290: Eddy current testing - Signal Analy
Page 291 and 292: Impedance Testing With impedance ma
Page 293 and 294: Phase Analysis Testing - Vector Poi
Page 295 and 296: Phase Analysis Testing - Ellipse As
Page 297 and 298: Figure 6.4: Cathode ray tube displa
Page 299 and 300: Figure 6.5: Screen image of a linea
Page 301 and 302: Impedance Plane Testing - Mode of O
Page 303: Figure 6.6: Null balance instrument
Page 307 and 308: For deep subsurface crack detection
Page 309 and 310: Multiple circuits are used througho
Page 311 and 312: This type of digital instrumentatio
Page 315 and 316: Read Out Mechanisms - Audio Alarms
Page 317 and 318: An qualitative meter response could
Page 319 and 320: Figure 6.13: A qualitative analog m
Page 321 and 322: Read Out Mechanisms - Cathode Ray T
Page 323 and 324: Figure 6.14: Numerical readouts/dig
Page 325 and 326: Read Out Mechanisms - Computer Eddy
Page 329 and 330: Probe Delivery System Instead of mo
Page 331 and 332: Chapter 6 Review Questions Charlie
Page 333 and 334: Q.6.1 Signal preparation is usually
Page 335 and 336: Q.6.7 Amplitude gates provide a tec
Page 337 and 338: Chapter 7 Eddy Current Applications
Page 339 and 340: Discontinuity Detection The theoret
Page 341 and 342: Heat Exchanger Charlie Chong/ Fion
Page 349 and 350: Heat Exchanger TSP Charlie Chong/ F
Page 351 and 352: Heat Exchanger TSP Charlie Chong/ F
Page 353 and 354: Figure 7.2: Phase-to-depth calibrat
Page 355 and 356:
The geometry of real discontinuitie
Page 357 and 358:
Figure 7.5: A multifrequency applic
Page 359 and 360:
Aerospace Applications Charlie Chon
Page 361 and 362:
The reference specimen and its asso
Page 363 and 364:
Dimensional Measurements Dimensiona
Page 365 and 366:
Figure 7.6: A single frequency hard
Page 367 and 368:
Conductivity Measurements Conductiv
Page 369 and 370:
Alloy Sorting Alloy sorting can als
Page 371 and 372:
In addition, it is advisable to hav
Page 373 and 374:
Answers Charlie Chong/ Fion Zhang
Page 375 and 376:
Q.7.4 Using multifrequency techniqu
Page 377 and 378:
Q.7.7 Response to multilayer varyin
Page 379 and 380:
Chapter 8 Other Electromagnetic Tec
Page 381 and 382:
Some other technologies that have b
Page 383 and 384:
Alternating current field measureme
Page 385 and 386:
Figure 8.1 shows the basic principl
Page 387 and 388:
ACFM Principle Charlie Chong/ Fion
Page 389 and 390:
ACFM Z X Bx =magnetic flux componen
Page 391 and 392:
Page 393 and 394:
The technique in its simplest form
Page 395 and 396:
Page 397 and 398:
Magnetic Flux Leakage Testing Prima
Page 399 and 400:
Figure 8.2: Equipment for magnetic
Page 401 and 402:
Magnetic Flux Leakage Testing Charl
Page 403 and 404:
The most commonly used inservice in
Page 405 and 406:
Magnetic Saturation Charlie Chong/
Page 407 and 408:
The magnetization curve is not retr
Page 409 and 410:
Magnetic Flux Leakage Testing Charl
Page 411 and 412:
Magnetic Flux Leakage The basic pri
Page 413 and 414:
Magnetic Flux Leakage Magnetic Flux
Page 415 and 416:
Special hybrid (driver/pick up) coi
Page 417 and 418:
At distances in excess of two tube
Page 419 and 420:
Figure 8.4: Remote field testing en
Page 421 and 422:
Remote-Field Energy Zones - in remo
Page 423 and 424:
Remote-Field Zone Transition Zone C
Page 425 and 426:
RFT - Flux distribution in pipe (a)
Page 427 and 428:
Remote Field Zone - The third defin
Page 429 and 430:
Amplitude (voltage) - The remote fi
Page 431 and 432:
RFT Charlie Chong/ Fion Zhang http:
Page 433 and 434:
The Remote Field Technique is an el
Page 435 and 436:
Remote Field Eddy Current Technique
Page 437 and 438:
More Reading: RFT Remote Field Test
Page 439 and 440:
These eddy currents, in turn, produ
Page 441 and 442:
The Zones Direct Couple Zone The re
Page 443 and 444:
RFT Probes Probes for inspection of
Page 445 and 446:
RFT Signal Interpretation The signa
Page 447 and 448:
RFT Reference Standards Reference s
Page 449 and 450:
Page 451 and 452:
Q.8.4 A generally accepted definiti
Page 453 and 454:
Q.8.8 The region of intense electro
Page 455 and 456:
Chapter 9 Eddy Current Procedures,
Page 457 and 458:
American Society for Testing and Ma
Page 459 and 460:
Military Standard The United States
Page 461 and 462:
EDDY CURRENT INSPECTION OF NONFERRO
Page 463 and 464:
. Probe positioning and feeding sha
Page 465 and 466:
3. Tube Inspection General (Refer t
Page 467 and 468:
F. INSPECTION RESULTS AND DOCUMENTA
Page 469 and 470:
G. REFERENCES The following documen
Page 471 and 472:
Page 473 and 474:
Q.9.4 Military Standards are design
Page 475 and 476:
Q.9.10 The system in QA3 is calibra
Page 477 and 478:
More Reading http://www.allaboutcir
Page 479 and 480:
Discussion Subject: discuss on the
Page 481 and 482:
Page 483 and 484:
Inspection from the Tube OD Most AS
Page 485 and 486:
Approximately 25 years ago, the AST
Page 487 and 488:
One additional advantage of OD ECT
Page 489 and 490:
The baseline eddy current test The
Page 491 and 492:
There is no standard accept/reject
Page 493 and 494:
Pulsed Eddy Currents Systems Charli
Page 495 and 496:
Although still an active research f
Page 497 and 498:
LOI (Lift-Off point of Intersection
Page 499 and 500:
Gap Point : Similar to the LOI, the
Page 501 and 502:
Driving Coil Charlie Chong/ Fion Zh
Page 503 and 504:
Hall effect sensors In opposition t
Page 505 and 506:
Crack Detection using Pulsed Eddy C
Page 507 and 508:
Fig. 1 (a) ARMANDA - Automated scan
Page 509 and 510:
Fig. 2. Images of the Eddy current
Page 511 and 512:
Reading 2: 4.9.2.3 Pulsed Eddy Curr
Page 513 and 514:
Good Luck Charlie Chong/ Fion Zhang
show all

Electromagnetic Testing

Create successful ePaper yourself

Delete template?

Save as template?